Having problems with your Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum ?

I'm trying to clean the brushes under neith and trying to figure out how to take to plastic part off so that i can clean underneith. I think the brushes come out but i'm not sure how.


Answers :

The brush block wasn't made to take apart and clean. The whole block will come out, it just cames catches that hold it in place.
Repair Help & Product Troubleshooting for Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I'm trying to clean the brushes under neith and trying to figure out how to take to plastic part off so that i can clean underneith. I think the brushes come out but i'm not sure how.


The brush block wasn't made to take apart and clean. The whole block will come out, it just cames catches that hold it in place. ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

My Bissell Quicksteamer Model 1960-R won't spray cleaning solution. I have cleaned it and taken apart the whole thing. I can't find any problems. The holes are not cloged where the water comes out as I disconnected it and blew through it to be sure. The lines show water trying to go through. It is as if it doesn't have enough power to pump the water out when I squeeze the trigger. I am thinking it is the pump thing but can't find a replacement part for it.


... Bissell 1960-3 QuickSteamer Plus Upright Vacuum

I HAVE A BISSELL PROHEAT 2X HEALTY HOME, IT WORKED JUST FINE THE LAST TIME I PUT IT UP. YESTERDAY, I NOTICED THE FLOW GAUGE WAS NOT SPINNING, SO I CHECKED AND SURE ENOUGH NO WATER WAS COME OUT. I CHECKED AND ALL THE TUBS AND EVERYTHING ARE IN THE RIGHT PLACE AND HAVE LIQUID IN THEM. HAVE TRIED PRIMING CLEANING THE BRUSHES RUNNING HOT WATER THROUGH IT... HELP


Have you made sure that the tanks are seated properly and the red \012(or black) auto-load gaskets are in place. \012Check the bottom of the Water Tank and the Formula Bottle to make \012sure each has a red auto-load gasket attache ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

When I flip the switch on my sebo x1 upright, a red light comes to the brush and bag icons. However, I cleaned out the hose and checked to make sure there is no obstruction from the brush to the hose also, or from the hose to the bag. It is clear that juice is coming to the vacuum, but there is no sign of life except the two red lights.


Thanks for contacting fixya. You should pull out the bag and reset the machine. You should take all the user replaceable items. And turn it on. You will get lot of errors. Then turn the machine off. Put back all the accessor ... Sebo Automatic X1 Bagged Upright Vacuum

I have a Hoover SteamVac F5914-900 SpinScrub... The last time I used the hand tool attachment, it worked fine. Just tried to use it again, and now I only drips of water will come out of the hand sprayer, if that. I have tried prepping it for up to 15 seconds like the manual says... no luck with that. Also it is making a big puddle on the floor, probably because the brushes on the main unit keep spinning when I am trying to use the hand tool which I dont think they are supposed to do? Can a


The brushes can be turned off on most of them via a switch on the hood. There shouldn't be water coming out onto the floor unless you are pulling the trigger at that top. You probably broke this when attempting to use the tools. ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Hi, There is a high pitched whirring sound coming from lower part of the vacuum. When I tilt it toward me (while standing in the normal vacuuming stance) the sound sometimes lessens for a minute or so. I have tried the following things: -cleaned the two sponge filters -emptied the dirt receptacle -removed the roller and cleaned it -cleaned the brushes -the belt is not ragged and does not seem floppy -checked all of the airways for clogs (including removing the wheel base) Can you help?


Your looking for some dirt stuck in some thing you didn't check yet. with the roller out and the belt out of the way run it to see if it still makes the noise. if it does then you looking at the impeller or the motor bearing themselfs those bearin ... Bissell 3750 Lift Off Bagless Upright Vacuum

Vacuum brush Everytime I try to vacuum the vacuum makes a very loud noise and starts to shake. I'm thinking it is the vacuum brush because it feels like that's where the shaking is coming from. Could it be the brush?


Your suspision may be correct especially if vac is well used/older however may i suggest you turn vac over and investigate by removing the brush cover plate? then you may see what problem is?this could be debri trapped in roller/brush hous ... Kenmore 23313 Whispertone Bagged Canister Vacuum

I cleaned out my brush in the bottom front, cleaned out the small tubing going into the canister, and the canister itself. I also changed the filter.I snapped everything back into place, but Since then, it doesn't seem to have any suction and there seems to be a space between the canister and the bottom of the vacumm where the canister sits. At that area, you can feel air coming out when trying to vacumm and it just doesn't pick up, it seems to be just blowing stuff around.


You need to really look at it some thing is out of line you shooed not have\015\012any spaces in the top or bottom\015\012pull the canister back out and look at the pins that you lined up with the\015\012to ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Making high pitched squealing noise and motor is hot...cleaned out brush area and made sure hoses were free and clear too..noise is coming from the brushes because when I use just the wand, the noise disappears


... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Electrolux power nozzle, model 1692, power cuts on and off. I don't have the manual for it, but I'm trying to remove and clean the brush compartment. I removed the top, but not sure how to get to the brush. I would like to find a manual for it, because it's completely different than the one I use to have.


... Electrolux Vacuums

No suction i have a bissell lift off revolution vacuum. I have cleaned all the filters and emptied out the canister made sure that the hoses are not plugged but it will not pick up unless you use the hose. the floor brush is clean and still no suction coming from under the vacuum... could you help me please


Is there a blockage in the small hose in the bottom of the machine \015\012take of the pod and you will see the small hose, \015\012Is the main hose pushed into the bottom housing ... Bissell 37603 Upright Vacuum

I can't open it to clean it, please help! I know I have to pull the grey cover, and I have tried hard but no luck. Seems attached from the bottom, so I am not sure how it will come out. Thank you for your help.


I had the same problem. It normally opens with a little tug on the door but if you are like me and you let it fill up with a year's worth of pet hair etc., the door will jam. The only option is to ... SweepEZE 600 C-1 Canister Vacuum

Roomba Scheduler Hi, my roomba scheduler is wobbling back and forth then stopping after a few minutes. It beeps "uh oh" and the orange status light comes on. I've cleaned every part I can think of or read about. I've replaced all the brushes and filters. Any suggestions?


... iRobot 4296 Robotic Vacuum

I took the cover off the brush so I could cut off all the hair that was wrapped around it (vacuum was working fine, I just noticed the hair). I pulled the brush/spinner thing off one side, cleaned everything, popped it back in where it belonged, and tried to make sure the belt was in the proper alignment. However, when I turned the vacuum on, it makes a horrible noise like I'm sucking up rocks. What have I done wrong in putting it back together? It seemed simple...


The ends of the brush roller have to go in in a certain position.each end has a different look.make sure the match up to the seats on the roller guides and make sure the belt is centered.the belt will center itself by turning the roller by hand in on ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

I have Bissell ProHeat 2X 9300-M that I tried to use again today. Is does not dispense solution when turned to Floor Cleaning, when switched to Hose it seems to be working fine. Brushes and suction are working as well. Soap and water containers are full. I took off and replaced tanks, waited to prime the pump multiple times without success. Not sure what is going on.


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

Little green machine pro heat pet the collection tank wasn't collection and dirty water was coming out of the bottom. i took it apart, cleaned it up and put a new "duckbill" gasket in. then it quit spraying, but i think i got that working again. now after i spray and get a good foam on the carpet, i switch to suction and it seems very weak. i can see the water moving (trickling) from the head into the hose but it is not reaching the collection tank -- actually, i am not sure where its goin


... Bissell THE BISSELL LITTLE GREEN MACHINE Vacuum

Bissell 8920 proheat x2 brushes not turning i only noticed this after i finished cleaning.. or kinda cleaning because of the brushes ntot turning.. water comes out fine suction is fine but its not scrubbing so its not as clean as it could be. manual part works well water coming out hot. I did take it apart and cleaned off all the hairs in hopes maybe that was it.. put it together still nothing.. No idea how the belts should look onit and i cant find a picture or a video showing how belts look o


Hello,\015\012\015\012Here's a link to a very helpful video that shows you step by step on how to access and replace the belt on your machine. When the brushes stop spinning, but the rest of the machine works fine, this is a tell-tale ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Roomba Discovery My Roomba turns on and moves but the brushes won't turn. Someone told me that I had forgotten to put in the yellow and black end bearings, but I did. Help, I miss my Roomba I have a Roomba 530, I have had it for 2 weeks and really loved it. I have followed all the cleaning instructions etc.. Then the Roomba wanted it's brushes cleaning "please clean Roombas brushes" So thinking that something was stuck I removed and cleaned the brushes, (yellow tabs on and in place by the way)


I read somewhere that you need to clear the software in case there is a glitch. To do this, take the battery out and then, simultaneously hold down the "spot" and "clean" buttons for 30 seconds. Replace battery. This has worked for my Discovery model ... Roomba Robotic Floor Bagless Vacuum

I have a DC07 and the brush wasn't rotating and I had no suction at the brush but perfect suction through the hose. I noticed a large build up of dog hair around the brush so I took off the cover plate and removed all the hair, cleaned inside the floor/brush housing and cleaned out the hose. I also cleaned the filter and removed the other air access cover and made sure that they were clear. I put everything back and the brush still doesn't turn and there is still no suction through the bottom


Hi and welcome to FixYa. I am Kelly. \015\012\015\012Here is a link that can assist you in your quest for the missing suction: \015\012\015\012 ... Dyson DC07 Bagless Upright Cyclonic Vacuum

I was vacuuming my room and all of a sudden I hear this loud noise, then notice the roller brush isn't spinning. Thinking too much hair was caught I separated it from the rod and hose to clean it out, but noticed that the roller brush didn't move at all while I was cleaning it. I've cleaned the brush before and it would roll around with little effort, but this time I couldn't move it at all. After removing hair and string I put the vacuum back together and started it up, but the noise continued,


It sounds like if the rod is clean then there is debree inside the roller where the rod fits in too. ... Hoover Platinum Cyclonic Bagless Canister Vacuum With Power Nozzle

Now that I just fixed my Lux Legacy canister vacuum, I need help on my other Electrolux Regency Series upright! The vacuum works fine but the rotating brush does not work and the brush motor does not turn on. Tried cleaning the brush and hitting hte reset button to no avail. This upright has a triple setting switch and I checked the each of the wires seem to be attached. Tried rotating the brush by hand and it would not budge. Was going to "encourage" the brush to turn with a set of articula


There are a couple rectangular holes on the bottom of the power nozzle, beside the wheels. These have tabs in them that need released with a standard screwdriver. \015\012 ... Vacuums

Hoover steam vac, brushes won't rotate, have cleaned filter by brushes, removed brushes and they rotate okay when off steam vac, tried to ajust level for carpet cleaning and brushes still don't move


There are three things to check when experiencing 'no spin' on the cleaning brushes. 1) Check the small pull out filter screen under the machine. It must stay clean for air to pass to the turbine which powers the brushes. 2) Check that the long shaft ... Vacuums

Scrubbing brushes I have cleaned the filter, checked the dial to make sure it is turned to high and cleaned all of the brushes. Still I can't get the brushes to rotate. What now?


Your turbine might need to be replaced ... Hoover F5881-900 Vacuum

My Roomba says to clean the brushes when the brushes are already clean. Is there something to take apart to check? I have already taken the brushes out. I don't know the model number, I think it's the 500 series, black and silver.


Turn the unit upside down and remove the bottom pan should be 4 or 5 screws depending on the model. next remove the 4 screws that hold the brush cartridge and pull the whole brush assembly out.using a can of compressed air cle ... Roomba 3005 Pro Robotic Vacuum

My roomba keeps telling me "error and to clean the brushes. I have cleaned the brushes and when I turn the roomba back on it keeps clicking underneath the roomba. I'm not sure what else to do.


I had the identical problem. I cleaned the brush but the problem persisted. I then put in a new brush that was provided in the box and the problem vanished. I have since used the cleaning tool on the old brush and will try and reinstall it to see ... iRobot 4150 Roomba Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0915 seconds