Having problems with your Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum ?

Hoover steam vac ls brushes wont turn how to clean turbine


Answers :

Repair Help & Product Troubleshooting for Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Hoover steam vac ls brushes wont turn how to clean turbine


... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

Brushes wont turn hoover f7412900 steam vac - Hoover SteamVac V2 6-Brush Widepath F7426-900 Vacuum


... Hoover SteamVac V2 6-Brush Widepath F7426-900 Vacuum

Brushes on Hoover Steam Vac F7441-980 do not turn.Brush control on;drive pin present;filter intake clean; Drive mechanism doesn't appear to be turning. Also when spraying on cleaning solution, spray comes out in streeks rather than the width of nozzle. JBB


... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

My brushes won't turn on my Hoover Steam Vac Cleaner. I have removed them and cleaned them and put them back in and they still won't turn. Any suggestions?


... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Hoover steam vac, brushes won't rotate, have cleaned filter by brushes, removed brushes and they rotate okay when off steam vac, tried to ajust level for carpet cleaning and brushes still don't move


There are three things to check when experiencing 'no spin' on the cleaning brushes. 1) Check the small pull out filter screen under the machine. It must stay clean for air to pass to the turbine which powers the brushes. 2) Check that the long shaft ... Vacuums

Hoover Steam Vac Dual VModel #F7430-900 the turbine does not turn


... Hoover F7220900 SteamVac V2 Upright Vacuum

I can't get the brushes to rotate on my hoover steam vac v. i took them apart and cleaned them and they still wont work. any ideas?


Scrubbing brushes are driven by a belt. The belt either broke or slipped off its pulley. ... Hoover Steam Vac Dual V w/ SpinScrub Vacuum

Brushes wont turn on hoover steam vac f7431-900


Need replaced TURBINE AND GEAR ASY \015\012part no: 91001097 ... Hoover F7431-900 SteamVac Vacuum

My brushes wont turn on my f7412900 hoover steam vac dual v


... Hoover Vacuums

Beater brushes not turning on the wife's Hoover Steam Vac model F5905-900. Found one prior ''solution'' stating that it sounded like the belt was bad. That was my original thought, but on checking schematics and trying to find part numbers at Sears Parts Direct and at Hoover, it does not appear the F5905-900 steam vac HAS any belts to begin with. What's next??


This one I can tell you about from personal experience with that generation Hoover Steam Vac. After using it about 7 or 8 times my brushes stopped turning also.I disassembled it (kind of like disassembling a Chinese puzzle box) and found ... Hoover F5905-900 Vacuum

Have Hoover F7452900 spin vac carpet shampooer and brushes won't spin. The screen by the brushes is clean and they are place in position to clean on carpet. I noticed that when I have the brushes out of the machine and turn it on that the white square that is on the base of the machine does not spin--this is where part of the brush connector fastens to make bristles spin.


... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Hoover Steam Vac Dual V brushes won't turn


The brushes are driven with air pressure from vacuum motor. The switch merely opens a small door to allow air flow. usually there is a screen that is plugged that stops air flow which stops the brushes from turning. I too only used the appliance once ... Hoover F6212-900 / F6215-900 SteamVac Agility Upright Vacuum

Hoover steam vac dual brushes will not turn.


The belt is broken. ... Hoover F6213-900 SteamVac Agility TurboPOWER Steam Vacuum Vacuum

BRUSHES WONT TURN ON HOOVER STEAM CLEANER - Hoover F5891-900 Steam Cleaner


Belt probably broken. unplug from power and remove the plate from the bottom of cleaner.belt should be visible on one side or other. ... Hoover F5891-900 Steam Cleaner

The Brushes don't turn on my Hoover Steam Vac DuetV


CHECK INTERNALLY SOMETHING MIGHT BE BLOCKING THE BRUSHES TO MOVE.CLEAN THAT MANUALLY AND TRY. ... Hoover Steam Vac Dual V w/ SpinScrub Vacuum

Hoover Steam Vac - Brushes not turned, no suction power


The Brushes not spinning is most likely is caused by seized bearings in the turbine, requiring shop service (easy fix). The suction issue can be caused by the standpipe seal missing or lower recovery tank not on properly, on some models missing front ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Hoover F7458900 steam vac brushes won't turn


No, there is a turbine that turns the brushes. You can take the top cover off to get to it, open it up and clean it out and then try it again. If that doesn't work, then replace it, or just replace it to begin with. ... Vacuums

Hoover Steam Vac Dual V Model F7223-900 brushes will not turn


... Vacuums

Hoover steam vac F7427-900, brushes stopped


This is not correct, the turbine bearings are NOT sold separately. Hoover only sells the entire turbine gear assembly complete, not in separate parts. \015\012\015\012To verify this, please see the parts diagram below, you'll see that ... Vacuums

Hoover steam vac v2, brushes won't turn. - Hoover F7425-900 SteamVac V2 Widepath Upright Vacuum


Hello,The Hoover SteamVac's are notorious for \015\012this exact problem. There are several things that can be causing this \015\012probelm.First, what you'll need to do is take the brush block \015\012out of the machine. To d ... Hoover F7425-900 SteamVac V2 Widepath Upright Vacuum

HOOVER STEAM VAC DUAL V STEAM CLEANER BRUSHES WONT SPIN


... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

HI, my motorized brush barely turns.It makes a hot rubber smell. I took apart and noticed the spindle the belt turns on discolored from heat. Cleaned it, but still no turning of the brush.The vac is a hoover wind tunnel. As it moved accidentally touched the belt/ spindle and burned my hand a little. Very hot in area. Bright spark from motor noted. Was careful not to touch that part!


That means that the belt is stretched and it is slipping on the motor shaft, that is why it is hot and smells like burning rubber. You need to replace the belt. Here is the correct belt you need: ... Hoover S3765-040 WindTunnel Bagless Canister Vacuum

Have a hoover windtunnel platinum. I have changed the bag ( hepa Q bag) but the bag light wont reset. so the vaccum wont turn on. I have unpluged it and let it set for a while with the new bag in and repluged it in. I have checked the brushes and it is all clean but it will not reset. This only the second bag so it is a new machine I should not be having problems. Is there some sore of reset button I can hit.


... Hoover Ultra U6430-900 WindTunnel Bagged Upright Vacuum

I have a hoover f5914-900 steam vac.. and I was wondering if there's a way to take apart the spin brushes to get them cleaned out well. I loaned it to family, and the brushes came back extremely soiled and not spinning.


The brush block may be removed from the base for rinsing.\015\012Yes, you can CAREFULLY disassemble the brush block assembly by releasing each of three latches that hold each of the clear gear covers to the main block. A small screwdriver is u ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Hoover steam vac dual Model # F74310-900 - Brushes won't spin. i've cleaned the little screen per owners manual and still no fix. What else could it be? I can spin the brushes by hand if i remove the assembly.


... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1186 seconds