Having problems with your Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum ?

Setting up for apolstery cleaning

\015 I can't find my owners manual and can't remember how to set up my hoover steam vac for apolstery cleaning.\015

Answers :

Hoover Steam Vac F5853-900 Series 17.9
\015\012Remove the tank front panel by sliding it straight up. Replace panel with converter (located on end of hose, end is shaped like front panel that you slide out.Before connecting tube to cleaner, make sure black tabs are extended by pulling tan collar roward tube.Open door on hood labeled "Stair/Upholstery Cleaning Connection" Press round solution tube connector onto round projection inside door. Press connecator collar down firmly to ensure that it is fully connected.
\015\012When the solution tube is connected to the deep cleaner, the nozzle brushes will automatically be turned off and will not rotate when the deep cleaner is turned on even if the speed selector is in the HI oar LO position. For full suction, it is important that the recovery tank lid is properly secured before cleaning.The tank lid is replaced in a hinge-like manner. Position front of lid under tabs on front of tank. Rotate lid down onto tank. Make sure lid is secure on all sides before cleaning.Hope this helps.
\015\012Good Luck
Repair Help & Product Troubleshooting for Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Setting up for apolstery cleaning

Hoover Steam Vac F5853-900 Series 17.9\015\012\015\012Remove the tank front panel by sliding it straight up. Replace panel with converter (located on end of hose, end is shaped like front panel that you slide out.Before connecting ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

Bissell will spray water when set to water rinse, but as soon as it is set to light, normal, or heavy cleaning, there is no spray. I have tried priming but to no avail. I put plain water in the solution tank to test without ay success. It is like it loses it's prime whenever you try to use a solution mix. Once you set it back to water rinse only and go through the priming steps, it is OK. Any help would be appreciated. Thanks.

Please check the following with liquid in both tanks.\012 \012- Check to see if the machine will spray through the hose with the setting on tools. If it does, the pump is fine. Continue troubleshooting.\012- Check for ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Isn't picking up lint. Will pick up other things like flecks of paper but will not get any fuzz or fibrous material off any rug no matter what the setting. This is a recent problem. Have owned the vacuum for awhile and never seen this issue before. Is it an easy fix? I've cleaned the brush, cleaned out the filters, cleaned the dirt tank. Nothing changed.

Is the brush turning on the bottom of the machine ? If not It could be clogedup with stuff or the belt could be worn on it and it will turn but as soon as it contacts the floor it will stop turning. The belt is easy to replace by removing screw ... Bissell 3576 CleanView II Bagless Upright Vacuum

My Roomba runs for a while and says error 2 to clean the brushes. This happens with cleaned brushes. And I have followed the instructoins. i have got a brand new set of brushes also. When inserting them the same problem continues. The floor is clean.

Remove the two round rings.....this has worked for me like a charm since! So glad to have the Roomba back up and running! ... iRobot Roomba 560 Robotic Vacuum

My bissell proheat cleaner is letting out little spray solution when on the floor cleaner setting. If I press the sprayer on the attachment solution comes out of it even when it is not set on the attachment setting what should I do to fix i. How do I clean the water nozzles under the machine?

Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Bissell SpotBot model 7887 still seems to clean ok, but there is no wastewater appearing in its tank on normal "Fresh Stain" and "Set-in Stain" settings. Seems to work on the "Manual" brush setting though.

... Bissell SpotBot Robotic Wet/Dry Vacuum

My Hoover Windtunnel does not clean carpet. The machine keeps grabbing the carpet. It appears that even with the switch set for carpet, the machine keeps acting as though it were set for a hard floor. How can I fix it?

Move the height adjustment up a little ... Hoover U6476-900 WindTunnel Vacuum

Brush Roll belt stops turning durring vacuuming on WindTunnel self-propelled, v belt is a little loose with handle down. Tensioning roll is engaged OK, but fully at the end of its travel. Replaced belts flat and v, but still stops turning even on high carpet setting when vacuuming. Carpet setting and height adjustment appears to be working OK, roll is clean and turns easily when out. Also turns easily until it engages the carpet. Self propel function works just fine.

... Hoover U6485900 Bagged Upright Vacuum

My Rainbow E2 has been working great for years now, but recently it has stopped working on the vaccuuming setting, but will still run on the low speed air cleaning setting. I hope it is something as easy as replacing the switch. Would appreciate any tips to determine if that is the issue or possibly something larger. Tks in advance for the info/help.

Still need help, let me know.\012\012Thank you,\012Ralph ... Rainbow E series Canister Wet/Dry Vacuum

My Oreck XL upright is blowing out instead of sucking in. I changed the bag and cleaned the brushes; I also cleaned out the main "pipe." I looked for a place to change settings and couldn't find any, so I know I didn't inadvertently switch something. The brushes seem to be spinning at the correct speed. Thank you, Julia Byrem

... Oreck XL2200 Bagged Upright Vacuum

The hose works, however, when set to floor setting the machine will not **** up the water. I have tried cleaning the red vent too! Any suggestions?

... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

I lost my instructions to set up the carpet cleaning features. cant set it up

Go to the below site and click on the video clip you need. It's a lot easier to understand than a written explanation.\015\012\015\012http://www.kirby.c ... Kirby Ultimate G Bagged Upright Vacuum

Recently our Vitapur water cooler has not been dispensing water. The problem is the water is freezing in the upper reservoir. We have tried unplugging the unit overnight & turning it back on at the minimum cold setting several times which has not worked. We have also used the Vitapur cleaning kit to clean the unit, which also did not help.

The problem is a comon one and simple. You just need to replace the themostat.\015\012Good luck ... Vacuums

Now that I just fixed my Lux Legacy canister vacuum, I need help on my other Electrolux Regency Series upright! The vacuum works fine but the rotating brush does not work and the brush motor does not turn on. Tried cleaning the brush and hitting hte reset button to no avail. This upright has a triple setting switch and I checked the each of the wires seem to be attached. Tried rotating the brush by hand and it would not budge. Was going to "encourage" the brush to turn with a set of articula

There are a couple rectangular holes on the bottom of the power nozzle, beside the wheels. These have tabs in them that need released with a standard screwdriver. \015\012 ... Vacuums

The beater bar wont rotate when set to floor cleaning on bissell aromatic carpet shampooer

... Bissell Vacuums

Bissell cleanview reach no suction on floor cleaning setting

... Bissell Vacuums

Dyson DC14 suction still poor after all cleaning and new pre filter set.

... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

It will no longer vacuum up the water, Ive only used it 3 times! We unpluged it and let it set we even cleaned it out....

Hello..Try This: Remove the recovery (dirty water) tank, and then remove the lid. Now reinstall the lid (there are two tabs on the front of the tank, the lid must be installed over those two tabs, and then "rolled" trowards the back., It will "cli ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

When switching the vacuum (DC17 Animal) over to the hard surface setting (so the beater brush is not spinning), the vacuum shuts off. I cleaned the dust bin and checked the filter. I also cleared the beater brush of hair or debris that was wrapped around it. It still shuts off. Ideas? Thanks.

The drive belt has probably broken. You can get a replacement belt here:Dyson DC17 Belt ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

My wind tunnel keeps breaking its belt. The big one. The little one is properly attached. This is a recent problem so it has nothing to do with the rug height settings. I just broke two in the course of 15 minutes. The bag is NOT full, the brush/beater has been cleaned and properly attached Help.

Well will the brushes turn freely as they run in bearings if its got wool of cotton raped around the side of the brushs that will make them tight to turn and will brake every belt you put on it, in a flash,,,\015\012the other thing that causes ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

My hoover steamvac f5868900 has somehow been set to ''tool mode'' and I don't see a way to switch to ''clean mode''

... Hoover F5872-900 SteamVac Wet/Dry Vacuum

I have owned my kirby sentria for 2.5 years and have had no problems until now. The vacuum still works but I cannot lower it all the way down or the light will turn off and it will start to smell like something is burning inside. I use it on the 2nd or 3rd setting with no problem. I have changed the belt and cleaned all the hair and strings that were on the roller but it still has this problem.

Kirby has a 3 yr back to base guarentee so contact ur local rep or kirby direct and thy will sort it all from there, hope this helps :) ... Kirby Vacuums

Floormate Spinbrush The water comes out fine to clean but when I out it on the wet pickup setting, it piskc up in streaks and it has the most horrible sound while moving it around, like the rubber is going across the floor dry. Any solutions or anyone with similiar problems and a fix?

Not sure if this will help but these machines are ment to be used in one direction not back and forth like a vacuum cleaner. You should start in one spot and pull towards you slowly with the trigger depressed it is designed ... Hoover Floormate H3000 Upright Wet/Dry Vacuum

Dyson Animal vacuum is not sucking. Does not appear to have clog, have eptied and cleaned. Beater bar is turning, low airflow in carpet and attachment setting.

Hi its Darran at Dyson.We would recommend following the full blockage procedure and filter washing instructions outlined in your user guide, paying particular attention to the brush bar and soleplate area on your machine. If you do not h ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

I get a loud grinding noise when the knob is set to carpet and the brush is engaged. I made all visual checks per the manual. Everything is clean in in order. The noise originates in the housing where the selector switch resides

Its probably the clutch assembly that switch's the brush off and on. i would take it to someone to fix it, it isn't an easy job. ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0667 seconds