Having problems with your Hoover SteamVac F5914-900 SpinScrub Upright Vacuum ?
Constsntly applys water even when shut off/ not running took apart handle I believe trigger is broken
Hi there SmartAlec from NelsonVacuums.com.au here. The trigger definately could be broken but before you take it to a repairer i would really thouroughly clean any little foam filters and rubber seals you can find. I do a lot of work on the Vax range of machines (very similar) and 90% of the time it is the filters and/or the seals once they get a build up of shampoo on them they no longer seal properly but once removed and rinsed thoroughly they work again. Rinsing the machine through with clean water after a shampoo job will help this not happen again.
Hope this helps
Happy Vacuuming! :)
Hope this helps
Happy Vacuuming! :)
Repair Help & Product Troubleshooting for Hoover SteamVac F5914-900 SpinScrub Upright Vacuum
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
Constsntly applys water even when shut off/ not running took apart handle I believe trigger is broken
Hi there SmartAlec from NelsonVacuums.com.au here. The trigger definately could be broken but before you take it to a repairer i would really thouroughly clean any little f ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum
I have a Hoover Slider, Model #S2105, Serial #050500084989, and I need instructions on putting it back together; with parts and assembly of parts. I took it apart because it was making a noise, and I believe one of the belts had come off. However, when I took the screws out of the bottom to check the belts, the whole thing fell apart. Now I can't get back together properly. It will not come on, and I believe it is because the switch that makes it come on when you lower the handle is not posi
Greetings from GoVacuum,\015\012\015\012Please see the link below for a parts schematic to your Hoover Slider, hopefully this will help you put the machine back together. If you find a part that is missing, and would like to order one, j ... Vacuums
I have a hoover power scrub steamvac, the main soap dispenser trigger on the handle click when pressed and does not work (broken spring??) the other soap triggers on the hose and the trigger on top to dispense extra water both work. Can I fix the main trigger myself?
Water will not come out when i push on trigger button. So water does not come out. I have taken it apart and cleaned it. The problem seems to be in the triggerI push on the handle to release the water.
Order the part from bissel see if that fixes sound like you know what wrong just need get part number from bissell.Could be some kinda pump also thats bad not pushing out the water.I got bissle heated one black it only problem the seals r ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum
The Lower body of the Bissell QuickSteamer, water pours out from the body. Solution: I took apart the machine and there is a spring loaded valve with a rubber washer at the bottom. Think of the letter T upside down with the rubber washer on it. The washer stretches over the bottom and the spring creates a leakproof plug and won't allow water to pass till the button on the handle is pressed. This old washer came partially off and allowed water to leak. I purchased from the plumbing dept. a mi
... Bissell Vacuums
Water will not spray from floor nozzle but will spray from upholstery nozzle--solenoid broken? Bissell proheat 2X--took apart water is to the solenoid but not past it
Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum
I cannot charge my two year old electrolux pronto. I purchased a brand new hand held vacuum for it, but even the new one does not charge. When I plug in the cord nothing happens. If I turn on either the long handle or the portable unit within the long unit, the blue charging light comes on for a few seconds, then out. This tells me that the circuit is intact without a broken wire somewhere. I took it all apart carefully and could see nothing broken or out of place. On re-constructing it, it
It must be the charging transformer. We have already ruled out the vacuum unit. Unfortunately the transformer is not a serviceable part, and will need to be replaced. ... Electrolux Pronto 2-In-1 Stick/Hand Vacuum - Cayenne
Bissell 7901 Proheat Carpet cleaner water will not come out. Everything else works but it just will not wet the carpet... I have took apart the handle n I do not know where to put the spring back. Please Help
I took the trigger mechanism apart on the bin on my DC07 and cannot get it back together. It isn't broken
Try this linkhttp://dysonmedic.co.uk/replacing-dyson-dc07-cyclone-bin-flap-catch-clip/ ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
Bissell - Model 1697 - Powersteamer Pro - Carpet Cleaner I took the unit apart to replace some broken pieces and I can not seat the bottom to the top without properly engaging the soap/water mixer. What is the proper assembly procedure. What is the orientation of the water/soap mix valve when I seat the top to the bottom? The soap/water mix valve needs to engage the knob screw threads but this assembly is a blind operation. Do I turn to the soap/water mix knob to water only then seat the
Hi,\015\012http://dl.owneriq.net/7/7e477b7e-4440-49cf-a219-b68d301549e3.pdf\015\012This diagram will help you see the diagram plus the part assembly no and place it accordingly.I have also given link for Bissell - Model ... Vacuums
I bought new belts to replace the old ones (one had broken and the water would not feed) My cousin took it apart and now I need to put the new belts on and get it back together - do you have instructions or a diagram?
There are different variations with Bissell. They have the ProHeat series and a Power Turbo series. Below is a link with instructions and diagrams for the Belt Access Door. If this doesn't solve your problem or isn't the correct model, please post ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum
I took the trigger apart and cannot get it back together. It isn't broken.
... Dyson DC07 Bagless Upright Cyclonic Vacuum
Miele S318i worked ok till I took it apart to blow really fine ceiling "popcorn" dust that got sucked by the filters. When I plugged back in started for a milli second and quit. At this point I believe the circuit board might be the fault, but I want to test motor before I go and buy the part. Can I simply run 110 to the two moter contacts to bench test? Steve
Yes, you can. ... Miele S318 Bagged Canister Vacuum
My Bissell ProHeat 2x is pouring water out of the bottom anytime it's turned on. I had it in the shop for no water, took it back again for the same problem, took it back again because it had no suction, finally took it apart and found the problem with the suction and fixed it myself. Worked fine for a day and now it is constantly leaking water, if it's turned on, and is useless for anything except for making a mess.
Took the unit apart and discovered my heater had small pinholes in the metal and they had put in silicone, instead of a gasket, which didn't seal. So much for the place I took it to "saving" my heater for me. I repaired it myself by getting a few o ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum
No Water My Bissell rug shampooer does not eject water or saop whan I pull the saop trigger on the handle. I checked both filters and they are clean. Then, I removed the container that sucks up the water and pulled the saop trigger, water barely came out of the tubes. I tried to clean the rug in our family room and the rug was not wet when I finished, no water coming out to clean the rug. HELP HELP HELP!!! I live in Colorado is there a Bissell repair shop near Denver, HELP!!! Thanks Dominick ema
Does water squirt out of the hose nozzle, if it does, then check the heater inside the handle asm. Make sure that where the tubes hook up to it are not clogged. If water doesn't squirt, check for the seal at the bottom of the tank, it needs to be o ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum
Took my Hoover Steam Vac apart to clean it and now it won't **** up the water but was working fine before I got the bright idea to clean it. Took four screws out but did not touch the motor. It puts out water and the brushes rotate but no suction? Thank you for your help, Cathy
The suction is created by the motor and is pulled to the motor through the flexible hose. The hose could have pulled off at one end or it could have torn in a spot where there is more pull on the hose like when you lay the handle down to empty dirty ... Hoover F7431-900 SteamVac Vacuum
I have a Model F7431-900 and is a SteamVac V2. When I press the trigger for water or cleaning solution, the water just runs right through it even after releasing the trigger. What kind of problem do I have? Is it most likely a valve problem? I'm handy at fixing things and want to avoid the large repair bill if I take it in.
This sounds like a stuck solenoid. The Dual V models use solenoids to contol soap and water flow to the floor, along with a pump unit. If your unit is 12 months or less it is under warranty. I am not sure about the cost of the solenoid. ... Hoover SteamVac V2 6-Brush Widepath F7426-900 Vacuum
I have 16981 Model. The trigger assenbly has snapped off the retaining pieces inside the handel. Can you buy a new handle with the trigger assenbly? What is price and part number? Also the lever to adjust the up and down movement of entire handle has broken. Can you buy? Is it possible to fix it and price for part?
The best place to obtain a replacement part for your unit is to either try and download an exploded view of the product, found in a service manual (which is often information restricted to the authorised repair agent), to get to the part number. ... Bissell 1698 PowerSteamer ProHeat Upright Wet/Dry Vacuum
I got my bissell for $7.50 from a thrift store, if you can believe THAT. Used it for the first time today after reading the manual online first. After filling the clean water bladder full of hot water and setting everything up the way I wanted, proceeded to turn things on and go for it. Well, the water/solution just kept coming and coming, without my finger on the trigger. Obviously something is jammed in the open position but where? The trigger moves freely.
This is the answer I got from Bissell:Please\015\012check the gasket at the bottom of the tank to ensure it is attached and\015\012not lodged in the reservoir of the machine. If this is not the problem,\015\012take the machine for i ... Bissell 8910 ProHeat Clear View Upright Vacuum
I have a Bissell Proheat 2XTurbo carpet cleaner. No water will come out when I squeeze the trigger. I have filled the solution tank and the water tank. I read the troubleshooting in the manual and have tried turning it off for a minute and restarting and nothing. I took out both tanks and reseated them and nothing. It has sat for over a year but did not have any water in the water tank. Some solution was left in the solution tank. How can I make the water come out? HELP!
Call BISSELL Consumer Services.\015\0121-800-237-7691\015\012Mon-Fri: 8am to 10pm ET\015\012Sat: 9am to 8pm ET ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum
My Eureka Atlantis Express is brand new - never used. I took it out of the box, read the manual, filled the soap and clean water tanks, put them in. I lifted the machine off the counter to take into the living room but all the water came running out of the bottom all over the kitchen floor. I can see where the little white plastic piece sticks up into the water release valve and lets the water out. How do you stop this? Can it be fixed?
... Eureka 2553A Atlantis Handheld Wet/Dry Vacuum
My Bissell Quicksteamer Model 1960-R won't spray cleaning solution. I have cleaned it and taken apart the whole thing. I can't find any problems. The holes are not cloged where the water comes out as I disconnected it and blew through it to be sure. The lines show water trying to go through. It is as if it doesn't have enough power to pump the water out when I squeeze the trigger. I am thinking it is the pump thing but can't find a replacement part for it.
... Bissell 1960-3 QuickSteamer Plus Upright Vacuum
Model 79011 ProHeat - First the water and cleaning solution wouldn't come out without pressing the trigger several times. Now the trigger doesIs there a spring on it inside the handle or do I just need to order new trigger. I have only used the cleaner 3 times.
... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum
We just took our dirt devil Platinum Force Carpet Shampooer Model CE7900 out of the box - first time used. It puts soap and water down fine, but we can't get any dirty water picked up. None of the trouble shooting suggestions in the manual apply. HELP! (We had only the power on when trying to pick up the dirty water.)
... Dirt Devil Easy Steamer Upright Wet/Dry Vacuum
We have bissell pro heat and I have put new belts on and took off the top plastic cover I blew out the lines and I still can't get it to pump water or solution. The red little spinner flow indicater does'nt get water, if I pour water into it it runs out the front. I guess I don't know what else to do. The machine worked fine the last time we used it about 6 months ago. Any suggesttions?
Did you check and make sure the belt is still on right? They do come off from time to time.There are like 6 long screws holding the top cover to the bottom. The are real pain in the behind to put back together once you take them off. T ... Bissell Vacuums