Having problems with your Hoover SteamVac F5914-900 SpinScrub Upright Vacuum ?

The spin scrubs quit working all of a sudden while i was steam vaccuming my carpet, there is a little dog hair in there but it doesnt look like enough to completely clog it, how do i get them to spin again?


Answers :

(1) Assure the Brush Control on the hood is NOT set to the OFF position.
\015\012(2) Remove the brush assembly by pulling/unlatching it from base on each side.
\015\012(3) Does one of the brushes have the drive pin present? It should be about ¼ inch square, and two inches long. It attaches the brushes to the drive mechanism.
\015\012(4) Remove and clean the intake filter. One the base of the cleaner, behind the brushes, squeeze the two red abs together and pull the panel down to access the screen. Clean the hair/debris off the screen and reassemble.
\015\012
\015\012
\015\012
Repair Help & Product Troubleshooting for Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

The spin scrubs quit working all of a sudden while i was steam vaccuming my carpet, there is a little dog hair in there but it doesnt look like enough to completely clog it, how do i get them to spin again?


(1) Assure the Brush Control on the hood is NOT set to the OFF position.\015\012(2) Remove the brush assembly by pulling/unlatching it from base on each side.\015\012(3) Does one of the brushes ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

I have a bissell pro heat and it wont dispense water. the little red thing wont spin and it looks like the belt doesn't move. within a few minutes you smell it getting hot.


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

Aquamate basin pump does not work. Used it 3 times, stored it for a year and pump does not work. Looks like a reliability issue. Is this product defective for everybody? I saw an ebay listing for the basin that states "the pump works." Looks like I am not the only one with this problem if he has to mention that the pump worksl How do I get a basin with a working pump? gap920


Hmmm............ looks like the impeller is already stuck from a year w/o using it!\012\012\012I suggest if u could open it and spray some penetrating oil on the bushing of the pump motror and the impeller, force the motor to turn m ... Rainbow E series Canister Wet/Dry Vacuum

Have Electrolux 1590 whole house vac, and can't see how to get brushes out. Leads so short, and don't want to break them trying to free brushes. Do they slide out of plastic housing? My eyes not real good, but it looks like the leads are part of a brass sleeve that slides into the plastic housing. It also looks like the plastic housing may be a snap lock type, but I don't see how to open it.


... Electrolux Vacuums

Rick E1, it looks like the Motor Pulley, Elna #440152-20 needs to be replaced on my 722010 model (flat on one side from standing around. It looks like some kind of a set screw which keeps it attached but are you familiar with how to get this item off the little shaft it is on. Also, any idea where I could find a reasonably priced Motor Pulley.


... Vacuums

Just bought a 5 gallon shop vac the casters dont look like they fit the holes are small the casters have a nob on the end that doesnt look like it would fit unless you pound it in and i dont think thats right what do i do?


... Shop Vac 925-13 Canister Wet/Dry Vacuum

The inner pot's coating for anti-sticking is chipping off now for the pressure cooker model number 22027 sensio Inc and it looks like we need to order another innerpot of the pressure cooker. 1) we are wondering whether we can get the contact informaiton to get this done 2) could we also get stanless inner pot? Julie change [email protected]


... Vacuums

I just received my Hepa filter in the mail today. Product #XSH621 - Hepa filter for EP619 & EP621 :005-04 When bought my vacumn, I was told that the filters were free and all I do is pay Postage. Today I received one filter and it lookes like I got charged the postage for two filters. The packages slips: One stated order #11152282 The other order # 1151940 If I get charged for two I expect to receive two. Can you help me with this matter or where can I go to get resolution. Catherine Fantini e-


This isn't really a problem that can be fixed here on Fixya rather than advise you as a buyer. You'd have to contact the people/company you have purchased the filters from and take it up with them regarding the postage. Hope you get a decent reply. ... Euro-Pro Vacuums

Not enough suction going into my turbo brush so it spins. Ive cleaned it checked the belt it still doesnt spin. how to fix this problem?


... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

I have a Eureka 4870GZ. It turns on, but the brush roller doesn't move. The belt looks fine. I do have an extra belt and would try replacing the old belt, but I can't get the old one off the motor shaft or the new one on. I called Eureka customer service. The lady said there's supposed to be a small space between the motor shaft and the outside edge of the vacuum where I can slip the old belt off and the new one on. I don't see it. It looks like the motor shaft goes into a recessed place in the


Remove the top cover so that you can access to belt, You'll find 2 rows of 4 decorative holes on the top cover, In two of the holes you'll find the screws, Please use a flash light to see in that., Once the screws are removed, you'll be able to ... Eureka Vacuums

Kenmore Model 116 28014700 intuition vacuum cleaner. Latch for hose connection to cannister broke. I have the new part. How do I remove the hose from the broken part and replace it on the new part? I have already purchaed the new part p/n KC92PDDUZV06 for this, bt can't figure out how to get the old part off. It looks like you must destroy old part in order to get it off.


... Vacuums

My Bissel Proheat smartmix bottle is emptying really fast and it doesn't seem like the carpet is even getting wet. I am just trying to do a rug in the kitchen and have filled the smartmix bottle 3x now and the rug is barely wet yet. I have cleaned out the flow indicator filter and it does not spin when I push the button like it used to. I have also checked the belt and it seems fine. It is actually a Bissel Proheat 7901/8910 (Pet) but they could not find my product. Any suggestions, I am


... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

Roomba Discovery Roomba is fully charged and cleaned with sensor wiped clean. When turned on it it sounds normal and commences to go, but it then acts like it is putting on the breaks, spins, tries to go and manages a short distance and breaks again, just not making any progress because it keeps breaking after a foot or so and turns and tries again. Sometimes is gets so stuck from moving forward at all, like it is stuck in one spot just trying to go while seemingly surrounded by barriers. Somet


I had the same back-up, turn, move forward a couple inches, backup-up, etc. problem. Try cleaning/cutting the hair, etc. out from around the brushes, as well as around the ends of the brushes. Also, try a Q-tip to clean out the four pair of sensors ... Roomba Robotic Floor Bagless Vacuum

I have a Hoover, Steam spin scrub, Model F5897-900. Only used it a couple times and the motor gave out. First started being noisy then a bad smell. It did seem noisier that what I would expect from the start but I didn't realize it was a problem with the shaft of the motor. I took it apart and found the motor shaft wasn't true and causing sparks. The motor looks like it can not be taken apart and repaired. This seems like a default from the beginning but it is past warranty. Also noti


You will have to replace the motor and the hose asm. thehooverstore.com may be able to help, or you should be able to find a repair shop that can order them for you. ... Vacuums

The brush is not moving on the vaccume. I'm pretty sure that the belt is busted. I cannot see how to get the shroud off, so that I can get to the roller and belt. It all looks and feels like one piece, even when I start removing screws. It is a bag-less vac. The model number is - v1310rs. Thank you.


I know on my Eureka I had to remove a couple of screws on the bottom and then get a flat blade screwdriver and wedge it on each side of the base kinda next where the end of the roller would be and it snaps up and off. Really weird I thought but that' ... Euro-Pro Shark Professional Upright Vacuum with Bonus StickVac Red Bagless Vacuum

My euro steam mop is not getting steam to the head, it gets hot but no steam comes out. looks like an ongoing problem with these mops/ can you help?


Hi,Here is a tip that I wrote about the Euro-Pro Shark Steam Mop and why it maynot be getting steam to the head...Euro-Pro Shark Steam Mop Problem ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum

No "sucking" action i'm not getting any air to **** up anything, i cleaned it up put new belt on, doesn't look like there are any obstructions can't get it to **** up anything


Did you check to see if the beater brush was rotating properly?\015\012When it doesn't it usually causes the belt to burn and break, though I do not believe you had a belt issue.\015\012\015\012If you remove the beater brush like you did to rep ... Hoover Tempo Widepath Upright Vacuum - Blue

I have an older Wega 2 group espresso machine. Looks like a date of 1992 on the group head, but not sure. This has no model name that I can find. Anyway, when I turn it on I get all lights flashing after it heats up 5 minutes or so. I do get nice steam from the wands. I drained teh tank and found a little scale, but not much. I took apart the group heads and cleaned them thinking it may be a clog there, but that doesn't seem to have worked. Also fwiw the water level float is not visible and whe


For a new fridge, need more time to maintain the required temperature of the fridge abut mainly the goods in it? So everything seems normal. The time will be reduced day by day since the goods will stay for longer time in and door opening will bec ... Vacuums

Motor is sparking and smells like burning rubber. When it first happened I thought the vacuum had something jamming the beater bar. That was the smell it had, like when the belt gets burned. But when we turned it over, it wasn't jamming. Took off the base plate and turned it on. The motor area is sparking and it makes a weird noise (I assume that is because the motor fails and restarts). I looked for loose wires, can't find any. I believe I need some sort of part replaced, maybe even a n


From sound and description most possible is motor is burnt up sparks usually mean metal on metal either bearing or bushings went on motor if u can jiggle the shaft thats bearing if u rotate the shaft by hand and feel and or hear rough grinding the br ... Oreck Vacuums

I have a Bissell pet hair eraser model #3920. It's been working great until last night. I went to use it and the brush won't spin. It also smells like it's burning. I checked the belt and it looks fine, and the brush spins by hand easily. It's not clogged anywhere that I can see. Anyone have any other ideas? This vacuum is only 8 months old.


- Remove the access panel, which is on the bottom of the machine. There are 4 tabs to lift on the access panel to remove. Start with tab 1 then 2-4 tabs.- Check the brush, and belt for any damage. Clean off any debris on the brush. ... Bissell 3920 Bagless Upright Vacuum

Cannister model#11627915701. connector terminals in extensionwand ,and wlre harness in hose handle get hot,,,look a bit singed.. can order and do ourselves. but would like a "tune up " ,cleaning of vacuum as well. purchased in 2008. have long haired dog,,,can't afford to be without it for very long. have sears store in clay ,ny. lady I spoke w/ says it would get sent out and take at least 2 weeks.!


... Kenmore Vacuums

Eureka 4870: when using hose, brush still spins, vacuum gets hot and smells like it's burning.


... Eureka Smartvac 4870 Bagged Upright Vacuum

I checked the belt and it has not broken, but when I start to vaccum the spinning head stops, and I start to smell a rubber smell...Do you think I need to replace the belt, I did get some string caught in it the last time I vaccummed, and it did stink like rubber then also...


Yes you do need to replace the belt they stretch out. Think of a belt like a big rubber band if you were to stretch it out and hold a lighter to it the rubber band would stay stretched out. That is the same thing that happen ... Bissell Vacuums

I have Optima, 12amp Eureka vacuum, Model 431, AXZ type and the extension hose for cleaning corners and edges --the plastic part that the attachments fit into has a piece broken off and tools don;t fit anymore. It looks like the hose attachment can be replaced--can it be and if so--where can I get a new hose attachment. It seems it is cheaply made of plastic and really shouldn't have broken a piece off.


... Eureka 431A Optima Bagless Upright Vacuum

Last time I used by Hoover it worked fine, took brushes out to clean them and now when I try to put them back in they won't snap into place and lock. Looks like all tabs on both sides of the brush piece are there and I spin the brushes for the center spindle to line up but it won't snap into place.


Just slightly turn the brush wheel, The tabs look square, but are just a little different in one direction ... Hoover F7425-900 SteamVac V2 Widepath Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0562 seconds