Having problems with your Hoover SteamVac F5914-900 SpinScrub Upright Vacuum ?

What can be done with the scrub brushes not working, not spinning.Ihave cleaned the filter etc.

Answers :

I you are unable to turn them by hand while in the machine, then the turbine requires service. this I would recomend an authorized shop to address.
Repair Help & Product Troubleshooting for Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

What can be done with the scrub brushes not working, not spinning.Ihave cleaned the filter etc.

I you are unable to turn them by hand while in the machine, then the turbine requires service. this I would recomend an authorized shop to address. ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

It seems to be blowing dirt around not suking but when removing the attachment to clean stairs etc the pipe works fine have washed filteR ? SLIM UPRIGHT DC ALLERGY 18. Have cleaned out filter emptied cylinder taken any bits of cotton or hairs from brushes..........

... Dyson DC07 Bagless Upright Cyclonic Vacuum

Vaccum brush not working. Filters clear of debris has been smoking will not **** anything up help! I cleaned the brush up, cut hair out, etc. Still the brush will not turn and it smokes a little, is this a belt problem?

Yes you need to change the belt. Here is a link to the belt you need and to a manual you can view:Bissell Lift-Off Revoluti ... Bissell Lift-Off(R) Revolution(R) Turbo Upright Vacuum

My brushes on my hoover streamvac will not rotate. I removed and cleaned assuring that the filter was also cleaned. The only different thing I have done is to insert the upholstery attachment and removed it after use (didn't work so well) suction seemed weak. I am also noticing that there is air being blown out of sides where the dirty water container is. (don't recall that in the past).

... Hoover F5900-900 Upright Steam Vacuum

The brushes don't turn. It runs and dispenses shampoo and water and sucks it up but the brushes stand still.I cleaned them and filter etc still doesn't work.

There is a plastic shaft on the back of the block brush (spin scrubbers),\015\012 these wear out or break. You may need to replace the block brush. Or if the shaft is not broken it could also be the Turbine Gear. This is \015\012what the block bru ... Hoover F7220900 SteamVac V2 Upright Vacuum

I have a vax spin scrub V124. The brushes won't turn. I've cleaned the filter etc, but nothing.

... Vacuums

Bissell Proheat I have a Bissell ProHeat 12 amp 6 cleaning brush upright and it won't turn on anymore. We have done the basics like making sure the outlets work, etc. Changed it around to different outlets. It is not turning on. Any idea?

Things to check are the cord, switch, and the motor. ... Vacuums

Hoover Max Extract LS F6056900 Hand Tool not working / Cleaning Solution I need to know what I need to get in order to have the hand tool work on this model. Also, what cleaning solution is best for pet stains? Tried cleaning, pre-treating with Spot Shot and towel and/or scrub brush, then cleaning, still doesn't work. PLEASE HELP!!

... Vacuums

I have a vax cylinder model V-094. Working fine then started to play up. Switch it on and the motor seems to struggle to power up. Kind of wurrs up and down. Was thinking it could be the brushes have worn. Tokk to bits and cleaned her up, took a look at motot and brushes, cleaned them too, back together and still them same problem. Help please, hoover is not old but has done some work really don't want to through away something that can be fixed.

Hi.\015\012\015\012after all you have done I would be pretty confident its the motor thats faulty they are expensive to buy so machine is going to be scrap,\015\012\015\012Sorry.\015\012\015\012 ... Vacuums

Bissell 8920 proheat x2 brushes not turning i only noticed this after i finished cleaning.. or kinda cleaning because of the brushes ntot turning.. water comes out fine suction is fine but its not scrubbing so its not as clean as it could be. manual part works well water coming out hot. I did take it apart and cleaned off all the hairs in hopes maybe that was it.. put it together still nothing.. No idea how the belts should look onit and i cant find a picture or a video showing how belts look o

Hello,\015\012\015\012Here's a link to a very helpful video that shows you step by step on how to access and replace the belt on your machine. When the brushes stop spinning, but the rest of the machine works fine, this is a tell-tale ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Scrubbing brushes I have cleaned the filter, checked the dial to make sure it is turned to high and cleaned all of the brushes. Still I can't get the brushes to rotate. What now?

Your turbine might need to be replaced ... Hoover F5881-900 Vacuum

Hi, I have not owned my electrolux pronto 2 in 1 for very long but the roller brush has stopped turning. The handheld part works and the green light is on. I have done a thorough cleaning of the roller brush and all other removable parts. What might be causing the roller brush to not work? Thanks, Jen

Check the end cap bearings ... and replace the belt even though it may not be broken. Put a drop of sewing machine oil (no more) in each end cap bearing. ... Electrolux EL1000A2 Pronto Bagless Stick Cyclonic Vacuum

My hoover spin scrub brushes stopped spinning and i have cleaned intake filter and tried to turn the thing that spins it...when brushes are off the hole turns then as soon as i connect brushes the brushes will not turn what else can i do!!???

... Vacuums

The brushed on my steamvac Dual V F7227 are no longer working. We have pulled and cleaned the brushes, and the filter, but the brushes still will not come on. I saw a reply to one person that it is the belt. If so... how do I change it?

Greetings from GoVacuum,The Hoover SteamVac's are notorious for this exact problem. There are several things that can be causing this probelm.First, what you'll need to do is take the brush block out of the machine. To do this ... Hoover Steam Vac Dual V w/ SpinScrub Vacuum

The unit works fine for 10-15 minutes, then the power cuts off. If I let it rest for 15-20 minutes, sometime it starts right up again. The filters clean clean, the brushes are not restricted, the retainer is empty. ???? Tom Abbott

Hi, it is over heating due to insufficient air passing through the motor and a heat sensor is cutting out the power due to a blockage maybe a filter or a cloged hose.\015\012\015\012\015\012The ... Dyson DC07 All Floors Bagless Upright Cyclonic Vacuum

Dyson dc animal 27 suddenly very difficult to push on carpet. have freed brushes from any hair etc., checked filters are clean etc. Any suggestions please?

Check brush roll fitted ok. no missing broken wheels.ensure both belts if fitted are ok... ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

My Dyson DC07 is screaming load. I have replaced the lifetime filter and the hepa filters. I also replaced the clutch and brush. I took the canister apart and cleaned it. It works, but is so loud something else must be wrong

... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

My Windsor Sensor XP12 says the bag is full when it's not. I have removed the hose, brush, and filter and cleaned everything. I can put a bag on without the cover and it works great. However, when I add the bag to the front cover and close the latch the right way, it does not work. I'm thinking that the cover is not seating the bag correctly over the hole, but I can't figure out how to fix it. Any suggestions?

... Windsor SR12 Sensor Bagged Upright Vacuum

My dc 05 isnt working and i cant understand why , i have cleaned all filters etc and i also changed the fuse on the plug , which after i didi that it attempted to start but then jus cut out again so i thought the fuse had blown again , so i checked the fuse but its working fine could there still be a blockage somewhere in it or is it something electrical which means my dyson has to go to the dump :(

Most common cause of this problem is a wire broken inside the flex, usually either just where it leaves the plug (easy to fix) or at the other end (more of a problem). In either case, this is no reason to dump the machine - it can be fixed at a fract ... Dyson DC05 Cylinder Bagless Canister Cyclonic Vacuum

I have a Hoover Steam Vacuum, All Terrain, and the bristle brushes are not rotating. They appear to be seated properly and, the entire vacuum is clean and free of lint, hair etc., so everything is working properly except the brushes do not rotate. Any help would be greatly appreciated. Thank you.

I checked the owner's manual and the parts breakdown for your model F5807. Both showed that your model has a stationary brush strip and not rotating brushes. Is F5807 the correct model number? ... Hoover F5807 SteamVac Wet/Dry Vacuum

I have a Hoover Agility Steamvac and the brushes will not rotate. I have cleaned the filters and the the "brushes on" feature has been selected. Any suggestions on what else I might try to get it working?

You have a broken brush bar belt. Just simply replace it with a new one. This is very cheap and easy to fix.Pull the cover off of the bottom of the Vac and the belt will be there. If it's not broken then it is still stretched to the point ... Hoover Vacuums

I purchased a hoover windtunnel 2 model#u8361900 in Dec 2007.I am very disappointed because the self cleaning filter is not turning and particles keep clogging in that area. I have manually removed the particles but the filter will not turn.I also haven't been able to use the pet brush for some time.The cleaner has not been used hard about once a week since it was purchased.I am not happy that this product has stopped working effiently since purchased 6 months ago. Thank you Marcia Long Pottstow

The filter stands up right.the bottom goes in first then snap in the top.turn it by hand and you should hear it click if you have it in right ... Kenmore Progressive Bagless Upright with Inteli-Clean SystemVacuum

My pet hair eraser smells like it is burning all the time and sounds funny. The brush will not spin once you have it on the carpet unless you hold it up a little while you are cleaning but then the whole vaccume is not on the floor. I have cleaned all filters and all and it does the same thing. My sister has the same machine because I raved at how wonderful this thing was for pet hair and mine has not worked right since it was about a year old and hers has had the same exact problem since it was

We had the same problem, and it turned out that the roller wheel height setting had broken, for no apparent reason, and was "floppy" so we had to lock it in to one setting with epoxy. Limits utility, but it works. Sort of. ... Bissell Upright Vacuum - The Pet Hair Eraser 1 ea Vacuum

Oreck XL21 just will not work at all any more. Beater is clean - belt is fine. Fresh bag - inflates. Took the thing apart - checked for blockages at intake, bag entry, and the tube. It just doesn't vacuum anything. No suction at all for anything stronger than air. I'd say it doesn't ****, but that would be ironic. Are these known for just "quitting" after a while? We take it in for maintenance as recommended to replace filters, etc. Is there some miracle trick to make it work or sho

Did you make sure the brush turns freely? Even though it is clean, if it does not turn freely with the belt, it will not beat the carpet and pull debris up into the unit.\015\012\015\012Another (drastic?) thing to try would be to take the unit ... Vacuums

My vax power 8, 2200 watts 300 air watts 4L capacity upright Hoover is brand new, I emptied out the dust/dirt collecter and cleaned the motor filter yesterday for the first time, i switched it on and all fine, the brush is spinning and the hose is sucking, put the Hoover to work it's fine for about 30 seconds then then suction stops and its dead it won't collect no more, so switched off taken apart again and the motor filter is blocked and full of dust, so I unblocked it, do the same process aga

I had the same problem. It looks like the seal on the lid on the bottom of the cylinder has fallen out when it was emptied. There is no longer a proper vacuum being created so you don't get the cyclone effect and the dirt doesn't collect where its su ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0866 seconds