Having problems with your Hoover SteamVac F5914-900 SpinScrub Upright Vacuum ?

Brush does not spin on my steamvac v.

\015 Brush does not spin\015

Answers :

The engine or electric motor must have been shorted by water getting past seal
Repair Help & Product Troubleshooting for Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

The brushes on my Hoover Steamvac Widepath LS SpinScrub model # F6040 900 are not spinning. What should I do to get the brushes spinning again?


On those models the brushes are turned by suction. 1. Check the lower tank to be sure its completely closed and sealed.2. Check the lower tank to be sure the tools filler plate is in place (if you used the tools recently)3. If both 1& ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Hoover steamvac Spinscrub F7222-900 brushes do not engage. Brushes will spin when unit is laid down and the brushes are pushed upward, forcing the male brush linkage into the female receptacle , but when the unit is stood up it disengages. Turning the switch on and off does not make a difference.


That's the way it's supposed to work. ... Vacuums

Hoover steamvac model f-5883-900. The brushes spin freely when i spin them myself,but dont spin when running. The vac runs but sounds differet like a higher hum. To fix this would the pin be broken or the turbine


... Vacuums

I have a Hoover steamvac Dual V carpet cleaner Model No. F7427-900. This is a spin scrub upright. My brushes will not work. We think the white square that the brushes fit up into in the center of the brushs is not turning. Can you help me.


You are on the right track! Place a screwdriver (flatbladed) into the white drive square and try to turn it. If it is locked up the drive assembly is your problem. It is very common for these parts to lock up because of the moisture involved with ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Hoover steamvac model f-5883-900. The brushes spin freely when i spin them myself,but dont spin when running. The vac runs but sounds differet like a higher hum. To fix this would the pin be broken or the turbine


... Vacuums

Brushes won't spin on a Hoover Steamvac SpinScrub Model F5918-900


Well the hand tool works off the suction of the machine and has nothing to do with the turbine that controls the brushes. if you can get the part i can walk you through taking it apart. when you write back, let me know what the model num of your mach ... Vacuums

Hoover steamvac. brushes aren't spinning


... Hoover SteamVac Spinscrub 50 Carpet Cleaner

My spin scrub brushes don't spin at all. - Hoover F7425-900 SteamVac V2 Widepath Upright Vacuum


Check that the belt that spins the brushes is not broken, also that the\015\012gear that drives the belt is turning.\015\012\015\012Tom ... Hoover F7425-900 SteamVac V2 Widepath Upright Vacuum

Lost manuel I am trying to troubleshoot why my spin brushes do not spin. I have lost my user manuel. Is there a copy of the manuel that can be sent via emai? Hoover Steamvac Deluxe


Http://www.hoover.com/CustomerService/Manuals/Default.aspx Above is the link to all hoovers owner manuals, you just have to pick your exact model from the list. As for the brush not spinning in most cases the belt gets bur ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

Hoover SteamVac F7222-900 steamvac Brushes do not spin. Looked at filter as per manual instructions but it was free of lint. Need to fix it, help please? Vacuum was used less than 10/12 times


Solution for Hoover SteamVac (F7452-900) brushes not spinning\015\012Uses the turbine model and same solution would be similar. Root cause is simply the main gear attached to turbine becomes stuck. This problem shoul ... Hoover Vacuums

I have a Hoover SteamVac, Model F5906-900 and the brushes won't spin. It's like something is froze up inside. I have read where the Brush Turbine might need to be replaced. Can you tell me where I can find the schematics or an internal diagram of this model so that I can take it apart. Or maybe you might have another suggestion. Thank you Pauline Newman


\015\012Hello,\015\012\015\012This is most likely the reason the for the brushes stop spinning. I've written a very detailed repair guide on how to diagnosis this problem. This will walk you through step by step with pictures, an ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

The spin scrub brushes do not spin. - Hoover SteamVac F5914-900 SpinScrub Upright Vacuum


Try this: Make sure the setting is set to floor, then remove the little window (you might need a flat screwdriver to "pry" it up) and clean off the filter. If there is a blockage, the brushes will not spin! I hope this helps, if so, please give fe ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Brush does not spin on my steamvac v.


The engine or electric motor must have been shorted by water getting past seal ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

My hoover F745 900 steamvac brushes will not spin.


If you are handy with a screwdriver undo the casing to access the roller. Once open usually about 4-5 screws you will see that the drivebelt ( rubber band ) has broken. This is the piece you need to replace. Usually most electrical store selling clea ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Hoover steamvac. brushes aren't spinning


... Hoover SteamVac Spinscrub 50 Carpet Cleaner

Hoover steamvac spin brush puts out water, won't pull it back up. Checked all parts, no cracks. Cleaned filter.


Check for the front panel duct located on the lower tank front. this is the part you need to remove to attach the hose. also check to make sure the lid is on and secure on the lower tank. remove the lower tank and look on top of the motor cover towar ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

The brushes will not spin - Hoover SteamVac F5914-900 SpinScrub Upright Vacuum


The belt maybe broke take a look to see if it is you maybe able to get replacement belt at walmart!!! :) amtnng ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

My brushes stopped spinning. what do i do? - Hoover SteamVac F5914-900 SpinScrub Upright Vacuum


You simply just need to change your belt. This models uses Hoover belt # 40201160 and can be found at www.vacbelts.com. ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

My brushes stopped spinning. What do I do? - Hoover SteamVac F5914-900 SpinScrub Upright Vacuum


Sounds like the brush belts has snapped and needs replacing, you should be able to get a replacement at most electrical stores, just take the make and model number with you. ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

I have a hoover steamvac dual v carpet cleaner it's only maybe 2 weeks old and already the brushes won't spin


One cause is that the recovery tank lid isn't on correctly and not sealing. If there is a foam filter on the inside of the lid, make sure it has a 1/4 in. gap from the top of the lid. There is another filter, from the bottom, it has a red frame, pu ... Hoover Vacuums

The brushes on the unit do not spin. - Hoover SteamVac F5914-900 SpinScrub Upright Vacuum


Try to clean the filter under the machine or the filter behind the clear plastic, were you see the hypnotic disc sprin that lets you know that the brushes are spinning. To remove : the plastic piece that looks like a triangle, ( were the indicator is ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

My hoover steamvac is no longer sucking and the brush doesn't spin


Assure the ring gasket is in place under the hood. A round rubber gasket must be in place on the round tube under the hood where the recovery tank sits to connect the vacuum from the motor to the round tube on the bottom of the tank. ... Hoover F7431-900 SteamVac Vacuum

My steam vac brushes do not spin - Hoover F7205900 SteamVac V2 Wet/Dry Vacuum


... Hoover F7205900 SteamVac V2 Wet/Dry Vacuum

Brush won't spin - Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum


It's more than likely that you have to clean the brush and its mounts mainly from hair, but also other dirt. Then it should be fine. You might want to disassemble the piece to get a better access, but only if you are confident, because it's important ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

The rotary spin brushes will not turn - Hoover SteamVac F5914-900 SpinScrub Upright Vacuum


Belt either came off or broke ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0549 seconds