Having problems with your Hoover SteamVac F5914-900 SpinScrub Upright Vacuum ?

Vac only one week old. Water pours out of hose when using tools,at toggle switch.

Answers :

You have a leaking baffle and seal.
\015\012If this unit is only a week old, you should have it replaced.
\015\012Even if you are able to repair the leaking, its just principle.
Hi, it sounds like that either their is a seal that has failed or that the switch that you press that then pumps the water out has jammed.
The problem is as its only a week old its not worth messing with as it would void the warranty.
The only thing you should try is pressing the button a few times and let it run for a minute or two then see if this makes a difference it might just be a build up of pressure causing the liquid to come out so try presing the button a few and let the water run and see if it stops.

If you still have the same problem then your best solution would be to get it exchange as clearly their is a problem with the equipment but give it good try first make sure you try the trigger a few times and just let it run for minute or two as it might clear after the pressure has been released.

Let me know how you get on ok
Repair Help & Product Troubleshooting for Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Vac only one week old. Water pours out of hose when using tools,at toggle switch.

You have a leaking baffle and seal.\015\012If this unit is only a week old, you should have it replaced.\015\012Even if you are able to repair the leaking, its just principle.\015\ ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

I bought a vacuum for my daughter and it worked a week before the switch went on it. how can i get a switch C2006B 31cx E306773 these are all of the numbers that are on it. Like I said she used it less then one week and it has sat since then. THank you Klynn1979 Kay

If this was new when you bought it, it should have a years warranty on it. Otherwise you will have to find a repair shop that will order it for you. ... Vacuums

My bissell proheat upright steam cleaner is spraying out through the attachments just fine, but will not spray to the floor when using upright. we've taken it apart to find that there is no water at all going through one of the hoses, but it appears the hose is connected behind the on/off and heat switches, we can't seem to figure out how to get in there to replace that hose....any suggestions on how to access this?? just curious how you would get in to replace the hose, we know it is the hose..

Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

I got this sewing machine , can anyone tell me what this control box is used for ?. It is mounted under the table in front of the motor,It says Control Box on the front and two push button number settings with can be adjusted up or down from ( 0 to 9 ) ,Next to these settings are two toggle switches. One is marked start with on and off and the other switch is marked end with on and off. Above these switches it it says Back Track . The tag on the box says ( Type LE -BB -24 - 110 - 220, 2

Still struggling with your model number. I understand from the added comment this is a Brother sewing machine. I was hoping to find a manual that would be of assistance. Here is a couple of websites that lists available manuals for Brother sewing ... Vacuums

I have a Craftsman wet dry vac with blower capability (22 L). While I was using it to **** up water, the water came out of the blower hose. Now I can't get it to work as a vacuum. What can I do to fix this problem? Is there a toggle switch somewhere that allows me to choose vacuum or blower? Also, will the vacuum still work without the filter nut attached to the plate? Please let me know at your earliest convenience. Thank you.

... Craftsman Vacuums

Windtunnel first one used 6 times beater bar stopped working, took apart cleaned and belt was fine. this one had a reset switch for beater bar. had insurance at best buy so returned for a new one. used 2x beater bar not working and not dirty, no reset switch on this one., now back to the store for another? i don't even want the same one. I wonder how many they are gonna give me. This seems to be a common occurance.

Sorry, you feel like that. I have rentals and 6 windtunnel's (I prefer the bagged ones) and have never had a problem such as you have described. I think Hoover makes a great vacuum. ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

Soap/water solution pouring out on floor when trying to use hose & attachments

I have the same problem. No solution being dispensed using the handheld attachment. ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

I have Nutone VX550C. Motor runs intermittently (cycles on and off rapidly--the light on the handle is blinking furiously) when I use the on/off switch on the hose. This happens at all of the wall connectors, so suggests a hose contact problem. Motor runs continuously when I turn it on at the switch on the wall unit.

The unit does have a switchs the PVC outlets, and it sounds like the hose mech to operate the switches is broken, and intermittently making contact. A replacement hose would likely fix the problem. Looked them up on the net, and they're not che ... Broan-NuTone VX550 Bagged Central System Vacuum

We have a dyson dc 07 animal the machine was working fine then switched off after returning to the machine minutes later it wouldnt switch on, i removed on off switch cover and used a short piece of wire across the brown wires flicked the wall switch and it worked, aha i thought faulty switch aquired a new one to no avail and now even the short piece of wire trick doesnt work, has the motor died do you think, it wasnt over heating or making strange noises prior to refusing to work

It could be the motor. I'm having to replace the brushes on my DC 05. It appears that you can only get brushes for the YDK motors in the DYSON, not the Panasonic motor. Which might be saying something about the YDK motors. What happens is that the ca ... Dyson DC05 Cylinder Bagless Canister Cyclonic Vacuum

Central vac our central vac will not work unless the main vac in the garage is switched on manualy.... its sucking fine but i have to switch it off at the main switch in the garage after i have used it normaly i just plug in the hose and vac away and it switches itself off we have just had cable installed with a fisher guy in the walls do you think that would be the problem thanks a lot

It is possible that the low voltage wiring that controls your central vacuum has been damaged during the cable work. You can check to see if the low voltage relay is working by shorting the two terminals together at the unit. Just disconnect the two ... M&S Systems AirVac AVP1200 Platinum Series Central Vac - 12,000 sq ft Bagged Central System Vacuum

I have a Holmes HOH-2400 oil filled heater. one switch of the double lighted switch has failed now only allowing me to use the 700 watt setting only. Whre can I find a replacement switch to fit. It will be an easy replacement

... Vacuums

DC07 DYSON REPLACEMENT HOSE. HOW DO YOU REMOVE IT FROM THE HANDLE. I have a kenmore whispertone 8540 canister vaccum. The electrical wires (3) to power the beater are embedded in the hose, in a spiral fashion. The yokes that hold the hose on both ends (and attach to the beater on one end and the unit on the other) have no screws or pressure latches; i don't want to use brute force as i may damage the attachment device inside the yoke. If someone can tell me the trick to get these yokes off each

Should be a pry off dot on the underside revealing a screw ... Vacuums

I had used Dyson DC08 to **** out a wet car carpet. A few days later when using the V/C, there was a burning smell. Subsequently I washed the flexible hose, changed the pre-filter and post filter , but I wrongly put the pre-filter in the spot for the post filter. When the V/C was next used, there was again a burning smell and sparks. The filters were switched, but the V/C would not re-start. What shall I do?

Hi there,We'd strongly recommend against using your Dyson to pick up water. If you haven't already got in contact with us directly, I'd encourage you to do so. One of our experts will be happy to recommend the best course of action. You c ... Dyson DC08 Cylinder Bagless Canister Cyclonic Vacuum

I recently purchased a Hoover SteamVac to replace an old one because the brushes would not turn. I used it last week and then tried to use it last night and the same thing happened w/ the brand new model - the brushes won't. I've cleaned the brushed, the filter and everything else I can see. Can you help?

Those things are a waste of money you better off renting one. but the only thing i could think of is that something is stuck or your belt came off track ... Hoover Steam Vac Dual V w/ SpinScrub Vacuum

My Tefal steam iron (Pressing Compact) blew a fuse. There was water in it and it had been used for about 15 mins. It had been leaking small amounts of water through he steam holes.I changed the fue and emptied as much scale as I could, refilled it and switched it on.Now it works but pours lots of water onto the clothes, making it impossible to use!

... Vacuums

Kenmore 21875 One day it's working fine. Next day, it won't turn on. When I attach the hose to another vacuum cleaner, it runs. Is there a reset button on the canister? Could it be the receptacle is bad? My Kenmore Progressive won't turn on today either -but was fine last week. I cleaned the filters checked for blocked air, tried a different outlet and no luck. I'll check the pins on the connections and see if one of them is not matching up or appears worn.

Give the prongs a wiggle and see if there is any play in them.Might just be a plug end. ... Kenmore 25512/ 25513 Progressive Canister Vacuum

We recently bought a home with a 52" Hampton Bay Berlini Model 729 395 ceiling fan with a light that operates on a remote control. There is also a wall switch plate with two circular controls - one pushes and spins, the other turns with 4 clicks. We can not get the light or the fan to operate using either the switches or the remote. We have checked the circuit breaker. The manual that came with the unit - provided to us from the previous homeowner - really only describes how to install the uni

Nancy do you want to sell the Berlini fan if youstillo have it? ... Vacuums

I have a dyson 07. Vacuum works fine, great suction using the hose. How do I switch to using the carpet vacuum. (I lost my instruction book) Thanks

If this unit has a suction hose built in to the handle, the carpet vacuum should start working after you return the handle hose to the proper position. ... Dyson DC07 Bagless Upright Cyclonic Vacuum

We have a series e rainbow cleaner. my wife had been using it i turned off and turned the canister up sie down to get the serial number. it would not turn back on.we need a new hose and thats why i was looking for the serial num. it has a rocker switch and the motor will work on low but will not run on the suction side. i have checked the wiring harnesses out as best i could without taken it all apart. im wondering if it may be the switch. it started once and then stopped.

There is one way to verify if it is the switch.It's kind of dangerous though,but not too bad.You need an extra piece of wire,fairly thick.I would use 4 guage myself.Hold it with pliers,just in case it gets hot.Turn the switch on and hold the wire to ... Rainbow Vacuums

While using, steam stopped coming out in force at the port levels in the head. Suddenly started high pitch whining, pressed button just above connection site and end flew off with great force pouring water onto floor and carpet. Unplugged immediately for safety and unable to get it to deliver steam force again. Less than one year old and used only 8-10 times only in walk areas where there is no carpet with distilled water. Please, advise, cannot find booklet. Thanks So Much, Beverly Crumme

Hi,Here is a tip that I wrote about the Euro-Pro Shark Steam Mop and why it may not be getting steam to the head...Euro ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum

Brushes stopped The brushes stopped turning while using the cleaner. I removed the brushes to see if the spindle was broken, it wasn't. I then removed the top plastic cover and checked the switch that engages the brushes; it didn't seem to be moving correctly. There's one spring on the switch - should there be two? Or do you think something has broken on the inside? Thanks for any help

Most likely the turbine is bad, it may just be clogged up, you can take it apart and clean it out real good. That may work, but it may not. Sometimes it is best to replace the turbine. ... Hoover F7431-900 SteamVac Vacuum

Power head attachment works great when plugged into the hose part of the vacuum. The problem is when I attach it to the tube for normal use there is no power. I have checked all the connections and switched the power switch on and off still no power from tube to power head. Is there anything else I can try? Model Callisto

Try having someone turn the machine on and off while you pull the cord in and out with the cord more angled towards the on/off switch. Sometimes these models have a break in the cord rewind and will not put the power through to the motor. ... Miele Vacuums

Kenmore Progressive canister model 116.27514700 Problem: Vacuum motor won't turn on. The power head operates, but nothing from the vacuum. Have checked all areas of airflow: hose, bag, motor filter and hepa filter. All are fine. Have checked and rechecked all electrical connections, all seem to be in working order. Vacuum hasn't run for a week or so, so it's not the thermal protector, unless it's defective. Vacuum was running fine last week. Didn't stop operating when using. Went to v

Hello! The culprit is the PCB Assembly; Part # KC86WBZR3000...Cost is $6.99. I would remove and inspect for burnt components, or broken wires...Then clean connections both male/female using an eraser, toothbrush and alcohol...Using a bright ... Vacuums

Shop Vac was working fine last time I used it. Now I try to turn it on and nothing. I have cleaned the terminals on the toggle switch. I know there is power to the switch

Try tapping the motor area with a piece of wood or something, damp usage may have seized it up a bit ... Shop Vac 925-09-62 QSP Plus Wet/Dry Vacuum

I have an old Shop Vac model 3331.5. This is a 12 gallon 1.5 hight peak shop vac with a detachable blower. After many years I decided to use the blower feature, but have lost the lost the manual. Question; how do I attach the hoses to the blower? The motor has that cap on it the direct the flow of air in one direction and the wide hoses do not fit over it. I may be missing a part, but I would think the directional cap would have to come off anyway.

Remove the cap that directs the air and insert the hose in there. ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0766 seconds