Having problems with your Hoover SteamVac F5914-900 SpinScrub Upright Vacuum ?

Where do I get parts for my Spin Scrub Wet Vac Dualy

\015 Looking for the canister that holds the water and the other one that the water fills up in as they are cracked.\015

Answers :

Parts are available through your local Hoover dealer, can be located on the hoover website by entering your zip code.
Repair Help & Product Troubleshooting for Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Where do I get parts for my Spin Scrub Wet Vac Dualy


Parts are available through your local Hoover dealer, can be located on the hoover website by entering your zip code. ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

I HAVE LOST MY INSTRUCTION BOOK FOR THE STEAM VAC SPIN AND SCRUB. I WANT TO USE THE STAIR ATTACHMENT, BUT I CAN'T FIGURE OUT HOW TO HOOK IT UP, OR OPERATE IT. I SEE WHERE THE PLUG IN PART GOES IN THE FRONT OF THE MACHINE, BUT I CAN'T GET THE OTHER PART TO SLIDE INTO PLACE ON THE FRONT OF THE RESOVIOR TANK AFTER I REMOVE THE FRONT PANEL, AS THE DIRECTIONS ON THE FRONT OF THE RECOVERY TANK SAY TO DO. THE FIT IS JUST TOO TIGHT. WHAT AM I DON'T WRONG- OR HOW COULD I GET A REPLACEMENT INSTRUCTION BOO


You can download a PDF version of the manual at the link below. I believe you can contact Hoover as well and they might mail you one.http://www.hoover.com/CustomerService/Manuals/Default.aspxGood Luck! ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

My shop vac blows dust as soon as it's turned on and throughout use. I have changed filters, nothing is helping. What part of my vac can not get wet, or is there a better way to clean out the system?


There should be a cover or sock over the filter,this will stop the dust.the paper filter is the part that can not get wet. if you don't have a cover for your filter use an old sock or something simular to a sock. ... Shop Vac 584-04-00 Quiet Canister Wet/Dry Vacuum

Model#F5858-910 hoover steam vac,silver ,spin and scrub. It doesnt seem to spray cleaner it seems to stream it now. what could be wrong? I cant get to end of where it sprays to see if something is blocking it . otherwise it works great. I have it about 8 yrs. always worked good until recently


... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

I have used my Steam Vac for carpeting, but until today, had never tried cleaning upholstery with the spin-scrub brush. I spent a miserable afternoon trying to control the spray, which seemed to go everywhere AROUND the furniture, but not ON the furniture! Additionally, I never did get the water into the recovery tank, despite many attempts to connect and re-connect the hoses and recovery tank/lid.


I can sympathize. My vac came with two handheld attachments. I have better luck with the handheld attachment that doesn't have the spin-scrub pads. To keep the water from going all over the place, you need to keep the part the you hold only about 1 ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Upholstery conversion I can't find where to attach the end of the upholstery hose so that I get suction.  I have a Hoover F5888 Steam Vac Spin Scrub.


Take out the duct in front of the tank (#3), the hose end will have a duct on it that you insert in its place. This provides the suction for the hose. Don't forget to put that duct you took out back in place, or you won't have suction when you use ... Hoover F5888-900 SteamVac Upright Wet/Dry Vacuum

I have a question?? Laudry detergent spilled on my dyson. The yellow plastic part that sits in the plastic tube where the dust is collected and spins, can I get that wet to wash it off?


... Dyson DC07 All Floors Bagless Upright Cyclonic Vacuum

Parts replacement We have a Hoover Steam Vac that has a broken part #10 in your picture or Part # 37271035. Does this part cover the whole top section of the Vac? Is it hard to replace? Where can you get the best prices on Hoover parts? I have been on Hoovers website and they don't even recognize this Steam Vac. which is hard to believe they don't even recognize their own unit? Thanks Ray


This the hood or top cover. There some screws on the bottom as well as on the top, then it comes off. ... Vacuums

Hoover Model U8185-900 beater bar part keeps smoking and burning up We've replaced the part Hoover PCB Display Bridge U8172 three times and the vac beater bar works for about a minute then the part starts to smoke and burns out again. I've taken everything apart but cannot locate anything that would cause this part to burn up. I think if I did not disconnet immediately, he vac would catch my rug on fire. Help? I didn't send back the warranty card, so I can't get any help from Hoover. Any suggest


I'm not sure why this is happening. Perhaps if you would contact Hoover and explain the problem to them such that it appears that there is a safety issue with their product, they might be more cooperative. If that fails, I have had luck writing let ... Hoover U8185-900 Upright Vacuum

LlllSteam vac ws working very well--shilfted to using hand vac on furniture--when I shiftead back to wanting to use the floor vacuum using the 6 brushes and the floor vac system, the r6 rotaty brushes will not turn or function. What do IO havae to do to get them to turn and function? The lever on the side ils set for carpet terrain. What do I do now to get brushed to turn and scrub as they should and did previously. James Yerges 1'630-232-2798 JMYerges&comcast.net


What is the exact model number of that unit. There are several with that name. The only things that it could be are the handle mechanism that activates the brushes or the indicator is not working nad the level that selects the brushes is not working. ... Hoover Vacuums

My Hoover steam vac spin scrub model 4060-900 brushes are not spinning and I have lost the manual. Any ideas. Thanks. [email protected]


The problem I found with one a neighbor was tossing out is the bearings in the part that drives the brushes were stuck. Lubing them up solved the problem, but took a bit of work to get into. This also provides a good chance to clean the crud out of ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Shark Euro-pro EP621 Bagless Upright Vacuum. Q regarding the brush not spinning / after troubleshooting and taking actions listed below, it now spinning for a few secs, but then stopping. Already removed hair, strings, etc. Checked that belt is aligned properly, checked that small wheel that turns belt is working (spins fine when belt removed. Oiled the turning parts a bit, that made it spin better, but still stops. It turns about 3-4 seconds then stops. If I switch it off and on again, I get ag


... Euro-Pro EP621 Bagless Upright Vacuum

Have Hoover F7452900 spin vac carpet shampooer and brushes won't spin. The screen by the brushes is clean and they are place in position to clean on carpet. I noticed that when I have the brushes out of the machine and turn it on that the white square that is on the base of the machine does not spin--this is where part of the brush connector fastens to make bristles spin.


... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Help. The brushes on my Steam Vac Spin Scrub


If you don't have the user's manual for the machine, here it is:www.thinkvacuums.com/pdf/uprights/Hoover_F5914900.pdfCheck your system for any obstructions that could possibly causing the problem. Also, remove the brushes and see if ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

My Hoover Steam Vac Spin Scrub aw/ Clean Surge


Greetings,\015\012\015\012A few more things that you can try on your SteamVac. First remove the dirty water solution tank from the machine completely. You should see where the solution tank was just sitting, a plastic casing with a wh ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

My Hoover Steam Vac Spin Scrub aw/ Clean Surge


... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

I have a hoover f7222-900 Steam Vac Spin Scrub. I


... Hoover F7222-900 SteamVac Upright Vacuum

Do not know how to use Hoover Steam Vac Spin Scrub


Hoovers website, Hoover.com has them free to print. ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Only 1 side of my pond vac 4 is getting wet with very little suction, the other side is bone dry with no suction


... Oase Vacuums

Need instructions how to use Hoover Steam Vac Spin Scrub. I borrowed it from my Sister and she left it with no instruction book or letting me know how to operate it. I put water & cleaner in top tank. That's all I know to do. Do I put any water in bottom tank? I figured not, since that is probably where the water goes when sucked up by vac. Do I leave lid on bottom tank? I usually use a commercial cleaner, and this is very different. I need to know NOW, as I must return it to her today, and I'm


I did have a solution in just a few minutes. Someone responded with a solution that gave me the website where I could go and print the manual in pdf, so did that, and checking instructions I was able to clean my carpets and get the shampooer back to ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

We are putting our Hoover steam vac F7425-900 back together again after getting a new turbine assmbly part. However, we have a part ( #38454-013) that we are unsure where it fits. Can you assist us?


... Hoover F7425-900 SteamVac V2 Widepath Upright Vacuum

DC15 Vac comes on but the head will nmot come on. Local Vac shop said circuit board was burn up,can I repair myself. where do I get parts


HighnTools had posted this solution - try it.\015\012\015\012I \015\012have finally fixed my sister's dyson dc 15 beater bar problem. It was just 2 tiny broken wires \015\012connect to circuit board lead to the beater bar ... Dyson Ball HEPA Upright Bagless Vacuum - Iron/Satin Yellow

I have a hoover f5914-900 steam vac.. and I was wondering if there's a way to take apart the spin brushes to get them cleaned out well. I loaned it to family, and the brushes came back extremely soiled and not spinning.


The brush block may be removed from the base for rinsing.\015\012Yes, you can CAREFULLY disassemble the brush block assembly by releasing each of three latches that hold each of the clear gear covers to the main block. A small screwdriver is u ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

The spin scrubs quit working all of a sudden while i was steam vaccuming my carpet, there is a little dog hair in there but it doesnt look like enough to completely clog it, how do i get them to spin again?


(1) Assure the Brush Control on the hood is NOT set to the OFF position.\015\012(2) Remove the brush assembly by pulling/unlatching it from base on each side.\015\012(3) Does one of the brushes ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Hoover steamscrubber I loaned my vac to my daughter who used it to clean shag carpet with lots of dog hair......now the scrubbers wont spin I have taken them (scrubbers) out and cleaned the vac....don't know where the lint trap is...but i DON'T see any part moving that would make the spinners rotate either Thnks...Lydia


I had the same problem. Fixed it by taking the machine apart and lubricating the bearing inside the turo tunnell. It's a pain, but not impossible if I could do you can. You must start by taking off the cover. Don't forget the scvrews on the front by ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0625 seconds