Having problems with your Hoover SteamVac F5914-900 SpinScrub Upright Vacuum ?

I have never used a shampooer before when I use it it says to empty out dirty water. I don't have any left. My tank is empty. Am I doing something wrong.


Answers :

Suggest that you do the following.
\015\012Remove the TOP ("Clean water") tank. Fill it 1/2 full of water. Put the top on the clean water tank and place it back on the machine.
\015\012
\015\012Release the machine handle and remove the cover of the "dirty" water tank. Inspect the back of the tank to be sure that the vacuum adapter in located in the rear of the dirty water tank. If not-that is your problem. If yes, restore the top to the dirty water tank.
\015\012
\015\012Power the machine on.
\015\012On a kitchen floor, power the machine on. Pull the trigger and hold it for about 30 seconds. You should see water gathering around the brushes. If not, that is a problem.
\015\012
\015\012With water around the brushes, release and lower the handle and and move the machine over the water. It should vacuum the water into the dirty water tank.
\015\012Is all of that happening?
\015\012
\015\012
\015\012
\015\012
Repair Help & Product Troubleshooting for Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have never used a shampooer before when I use it it says to empty out dirty water. I don't have any left. My tank is empty. Am I doing something wrong.


Suggest that you do the following.\015\012Remove the TOP ("Clean water") tank. Fill it 1/2 full of water. Put the top on the clean water tank and place it back on the machine.\015\012\015\012Release the machine handle and remove the ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

I bought the Eureka 4703D model vacuum and my very first time powering it on, it was extremely loud - abnormally loud, and I don't know if it is loud like that because I possibly put it together wrong, or there is something wrong with it or it was previously damaged and I would like to know if this is something I can fix myself or do I have to take it back apart and return it to Walmart where I purchased it from. When it makes the loud noise, it does vacuum fine but the noise is just unbearable


... Eureka Power Plus 4703D Bagless Upright Vacuum

I HAVE LOST MY INSTRUCTION BOOK FOR THE STEAM VAC SPIN AND SCRUB. I WANT TO USE THE STAIR ATTACHMENT, BUT I CAN'T FIGURE OUT HOW TO HOOK IT UP, OR OPERATE IT. I SEE WHERE THE PLUG IN PART GOES IN THE FRONT OF THE MACHINE, BUT I CAN'T GET THE OTHER PART TO SLIDE INTO PLACE ON THE FRONT OF THE RESOVIOR TANK AFTER I REMOVE THE FRONT PANEL, AS THE DIRECTIONS ON THE FRONT OF THE RECOVERY TANK SAY TO DO. THE FIT IS JUST TOO TIGHT. WHAT AM I DON'T WRONG- OR HOW COULD I GET A REPLACEMENT INSTRUCTION BOO


You can download a PDF version of the manual at the link below. I believe you can contact Hoover as well and they might mail you one.http://www.hoover.com/CustomerService/Manuals/Default.aspxGood Luck! ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

I have a Kirby and when I step on the on/off switch it doesn't stick. Is that something common or am I doing something wrong?


No, the switch is broken and needs to be replaced ... Vacuums

I have a bissell powerlifter carpet and upholstery cleaner purchased in 2000-2001 by my wife. the sprayer does not work, it appears that the liquid is not being pulled up out of the tank. i am wondering if there is a part missing from machine. something that may need to go into the main tank. please advise.


I knew someone who had a problem with bissell before. I think they had to take it apart and clean the hose, dirt could be clogging it. Or you could try contacting the company. ... Bissell Vacuums

My hoover belt keeps burning when i replace it. i dont have the manual so i dont know what im doing wrong.


Probably when you close it back together, there is a piece rubbing against that you do not see right away but could maybe hear it. ... Hoover Vacuums

Cannot get the tank to lock down on the turbo unit so it will **** the water up into the tank. Will not seat in place. need instruction manual to see what we are doing wrong.


There is a lip on the front of the tank, hook it under the front of the machine then it will lay down flat ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

I have a Bissell 9400 E pro heat turbo. It's only been used 4 times, today it sounded like something blew. All my house electrics went off...( blew the main trip) I did read some place that the motor can short out and blow the PCB. Hubby and I just took it apart..( what a pain that was) We can't see a thing wrong with the board...( I expected to see something black, or damaged).... because when it blew today there was a weird smell... sort of like garlic. Question... how on this spinning earth


I have the exact same problem! Just occurred today. When I switch it on it fires for a couple of seconds then takes all the electrics in the house out again.\012\012\012Did ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Bissell Powerease Lighweight Deep Cleaner. (Shampooer) After I fill the solution tank with the solution and water, I put it in it's slot, but all of the contents just come flowing out. I have only used this machine twice and it worked ok. You are supposed to press the trigger and the solution sprays out and then release the trigger when you want it to stop. But like I said, now I just put the tank on and all the contents come flowing out. I don't know what's wrong or how to stop it.


... Vacuums

Help, my new Sunbeam Slush Maker won't 'slush' - I just get VERY cold drinks! Have followed the instructions to the letter. Is there something I don't know? Perhaps I am doing something wrong? Brenda


Having same problem...think we have been ripped off! ... Vacuums

I have a new Toyota RS2000 that I was bought as a gift. I received it without a manual which I have now obtained, but now I have gone to use it the power lead does not seem to fit into the machine. Is it possible I was supplied the wrong lead or am I doing something wrong?


It is quite possible that you were supplied the wrong lead, seeing that the manual was missing, the contents of the package might well have been tampered with. Contact the person who gave you the machine and ask them to either check wit ... Vacuums

Just bought a Hoover steam vac. Did the dining room. everything okay.. emptied recovery tank and replaced. started on living room. dirty water not going into recovery tank. carpets very wet. What did I do wrong and how do I correct it


You may have put the lid on your recovery tank on wrong. on some models you have to lock the front in first then snap it down in the back. if you can pull the lid away from the tank then its on wrong and isnt making a seal. ... Vacuums

I have just replaced my Dyson DC14 Motor and now it blows the hepa filter out and filter cap off from under the bin the air is really hot. Is something wrong?


This video on the link below may help youhttp://www.youtube.com/watch?v=6HQx-gFA3MI ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

Kirby Sentria I bought my kirby sentria just before we were to move house and although I have the instructions somewhere, they will be boxed up and I so want to clean the carpets before I move. Problem is that I don't know whether the belt should be on or off when using the big silver front with the Kirby insignia on it. I know that the green light should come on when it is working properly and it does not, so I am doing something wrong. I can attach the attachments no problem but I want to use


If the green light is off, then its time to replace the band. This video shows you how. ... Kirby Ultimate G Bagged Upright Vacuum

I bought a used vacuum seal machine (hobart model ht-120) it does excellent vacuum but it doesnt seal correctly all the time. it seems like there is something wrong with the valve that activates the bar that goes up and makes pressure and heats the bag for complete sealing. The heating is perfect but what is not working is what make the bar go up and down.


... Vacuums

I have a new aw131 meat therm. I have put the probe in the roast and need to put it in the oven shortly. But it is not reading out the current temp of the meat. Is something wrong?


... Vacuums

Hoover floor mate/ wet/dry I added the water and turned on and no water is coming out? What did I do wrong, I dont have a manuel


I have had the same problem. I took the darn thing apart to see if the hose was loose. Come to find out that when you fold the handle there is an extension that sticks out. This extension pushes down on a plunger that allows the water to squirt out ... Hoover Floormate H3000 Upright Wet/Dry Vacuum

Motor still runs--sounds like jet engine. do I need a new motor? or is there some sort of muffler that has malfunctioned? vacuum belongs to disabled mom---so trying to do work ourselves--cant afford much. dont see anything obviously wrong--but know nothing about electric motors.


This little vac I think is actually made by Samsung. If it is ROARING and vibrating, either the bearings or suction fan is in bad shape. Remove the lid as if to inspect the belt and see if there is a visible intake opening with a plastic fan rotatin ... Bissell 3590 CleanView Bagless Upright Vacuum

Suction? Hi there, when I turn the vacuum on and place my hand under the roller brush, there is very little suction. Could something be wrong?


You won't feel a great deal of suction like you tried to do it. But look at the fan, if it isn't worn down, and the bag fills with air when you turn it on, then the suction should be ok. If you haven't changed your belt in awhile, I am sure that it ... Kirby Ultimate G Bagged Upright Vacuum

Steamvac The last several times that I have used the steam vac to clean the carpet, I've noticed that the solution is not coming out as a spray. Instead it is a steam. Is this normal or is something wrong? Thanks for your help..


You might try running a solution of vinegar and water thru it to clean out the lines and spray nozzles. Also are the brushes turning when you are using it, that could also be the problem. ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

I HAVE A HOOVER STEAM CLEANER MODEL#F5881-900 THE SOAP LEVER HAS NO TENTION,SOMETHING BROKE BUT DONT KNOW WHAT!


The valve at the bottom of the tank has a valve stem and spring, you may have to replace the spring maybe. \015\012\015\012Go to http://vacuumsuperstore.com/ ... Hoover Vacuums

Cleaned all of the lines, shampoo solutions will go through but the water from the tank is not going through. the floww indicator will start to turn then after a second it completely stops. What is wrong with this thing?


... Bissell Vacuums

Power drive Belt is OK - switch is on. Could something be wrong in the handle - switch area??


It could be but i dont have enough info to really help. if the brush isnt working it could be power from the handle, it could be a bad motor, it could be even as simple as something is tangled up in the brush and that will stop it from turning but yo ... Hoover U6311-930 Power Drive Bagged Upright Vacuum

Steam vac When the cleaning solution is despened it is coming out in a stream not in a spray. Is this normal or is something wrong? Thanks for your help..


Either the nozzles are clogged, or the brush block is not turning. ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0422 seconds