Having problems with your Hoover SteamVac F5914-900 SpinScrub Upright Vacuum ?

Brushes don't spin, brand new unit righr out of the box. lint filter is clean ... speed is set to high ... brushes are snapped in properly.


Answers :

There should be a switch on the head of the unit. Its probably in the brushes off position. I think its by the spin brush indicator on the left hand side
Repair Help & Product Troubleshooting for Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Brushes don't spin, brand new unit righr out of the box. lint filter is clean ... speed is set to high ... brushes are snapped in properly.


There should be a switch on the head of the unit. Its probably in the brushes off position. I think its by the spin brush indicator on the left hand side ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Isn't picking up lint. Will pick up other things like flecks of paper but will not get any fuzz or fibrous material off any rug no matter what the setting. This is a recent problem. Have owned the vacuum for awhile and never seen this issue before. Is it an easy fix? I've cleaned the brush, cleaned out the filters, cleaned the dirt tank. Nothing changed.


Is the brush turning on the bottom of the machine ? If not It could be clogedup with stuff or the belt could be worn on it and it will turn but as soon as it contacts the floor it will stop turning. The belt is easy to replace by removing screw ... Bissell 3576 CleanView II Bagless Upright Vacuum

Bissell lift off vacuum about 4yrs old. Extremely noisy. OK until before Christmas but getting worse every time it's used. Washable filters washed, HEPA filter replaced. brush bar cleaned of every scrap, hose empty,everything that can be cleared has been. Noise high pitched, screeching and can only bear to use it for a few seconds at a time. Suction OK. Mine is so loud I can't use it very long-high pitch screech. Can this be fixed or does the whole vacuum need to be replaced? It still cleans gr


Sounds like a bad motor. Could be either foot motor or main motor either way cost will be more than half of the unit. ... Bissell Lift-Off(R) Revolution(R) Turbo Upright Vacuum

Scrubbing brushes I have cleaned the filter, checked the dial to make sure it is turned to high and cleaned all of the brushes. Still I can't get the brushes to rotate. What now?


Your turbine might need to be replaced ... Hoover F5881-900 Vacuum

My Oreck XL upright is blowing out instead of sucking in. I changed the bag and cleaned the brushes; I also cleaned out the main "pipe." I looked for a place to change settings and couldn't find any, so I know I didn't inadvertently switch something. The brushes seem to be spinning at the correct speed. Thank you, Julia Byrem


... Oreck XL2200 Bagged Upright Vacuum

I have a Hoover Steam Vacuum, All Terrain, and the bristle brushes are not rotating. They appear to be seated properly and, the entire vacuum is clean and free of lint, hair etc., so everything is working properly except the brushes do not rotate. Any help would be greatly appreciated. Thank you.


I checked the owner's manual and the parts breakdown for your model F5807. Both showed that your model has a stationary brush strip and not rotating brushes. Is F5807 the correct model number? ... Hoover F5807 SteamVac Wet/Dry Vacuum

My Dyson DC 14 is making the horrible "ratcheting"sound only when the brush is engaged on the carpet setting. I have cleaned the brush, so there are no obstructions, the canister is empty and properly on the unit. I checked to make sure all of the "traps" and hoses are clear of obstructions, the belt is on the brush securely and moves freely, the brush itself spins freely, but there is still the "ratcheting" noise. Any other suggestions?


Our DC33 was making the same ratcheting sound immediately upon placing the cleaner/brush head on the carpet. We carefully pulled the beater/brush bar out of the vacuum. Once removed, we pulled the black plastic end off of the center rod. We discovere ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Spin brushes spin freely on steam vac when not attached to cleaner indicator screen not dirty speed selector is in high position brushes are clean spin brush indicator when brushes attached to machine does not rotate


If this is a Hoover Steam vac, the turbine which drives the brushes is bad. If not a Hoover, then what is it, they are different, need brand and model number. ... Vacuums

I cleaned out my dyson ball as it smelt when i hoovered, cleaned filters, washed out canister and took the screws out of the front bar so i could clean near the brushes.. now its making a high pitched noise and when i switch it off it makes a noise like an engine shutting down! Have i disturbed the motor?


Hi its Darran at Dyson. The screws on the base of the cleaner head should not have to be removed to access the brush bar so it is possible that the brush bar has come out of alignment, hence the noise the machnie is making. Pl ... Dyson Ball DC24 Bagless Upright Vacuum

Hoover windtunnel U6425-900 the brush roll is not turning. Both belts are in good shape, I cleaned the brush roll and it is free of debris, the setting is on carpet and the brush roll still will not turn. There is a "burning rubber" smell when you attempt to push the vaacum forward a few times. The small belt does not seem to be pulling properly but appears to be in good shape.


... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Hi, There is a high pitched whirring sound coming from lower part of the vacuum. When I tilt it toward me (while standing in the normal vacuuming stance) the sound sometimes lessens for a minute or so. I have tried the following things: -cleaned the two sponge filters -emptied the dirt receptacle -removed the roller and cleaned it -cleaned the brushes -the belt is not ragged and does not seem floppy -checked all of the airways for clogs (including removing the wheel base) Can you help?


Your looking for some dirt stuck in some thing you didn't check yet. with the roller out and the belt out of the way run it to see if it still makes the noise. if it does then you looking at the impeller or the motor bearing themselfs those bearin ... Bissell 3750 Lift Off Bagless Upright Vacuum

Folks, My wife and I own a three-year-old Hoover U6434-900 self-propelled "Wind Tunnel" upright vacuum cleaner. The problem is that, even on the highest setting (front-end as high as possible), it gets bogged-down in even shallow pile carpet to the point that the brush stops. I've cleaned the machine thoroughly, pulling hair, thread, dental floss and such from the brush (and everywhere else), including unscrewing the brush end caps and pulling out the cat hair mats which formed in there.


Check to see if the V belt sits too deep in the brushroll groove, if it sits too deep you will need to replace the brushroll. the top of the belt should be about flush with the brushroll. also you have to take the screws out of the self propelled uni ... Vacuums

Have ultra vision and have changed filter and foam filter, checked all hoses but still will not pick up. Belt is fine and brush is clean and spinning properly. dirt stays at top of filter instead of falling into canister.


My kids get mine stuck all the time :(Take the vacuum outside then:Remove the hose at the bottom and see if there is any obstructions. Also shake the hose to make sure there is nothing in there as well or take it out side and make s ... Dirt Devil Vacuums

What causes these things to become unbearably loud? We've cleaned evey filter on the machine, pulled every speck of hair and lint off the brushes, changed the belt, no clogs anywhere. I've totally (and I mean totally, down to the brushes on the motor!) torn this thing down and put it back together with no difference. Also have a Eureka bagless, and after minimal use, and almost anal retentive maintance, it does the same thing,to stinkin loud. Wish one would **** up the other to save a trip to th


A clog in the hose or dirt inlet by the brush roll will cause the motor to sound loud. But so will a bad motor bearing, or motor fan, in which case you would have to replace the motor. ... Bissell Vacuums

Despite having the small window cleaned out the brushs will not spin at high speed. They turn at the low speed only.


... Hoover V1 SteamVac SpinScrub Vacuum

Brush Roll belt stops turning durring vacuuming on WindTunnel self-propelled, v belt is a little loose with handle down. Tensioning roll is engaged OK, but fully at the end of its travel. Replaced belts flat and v, but still stops turning even on high carpet setting when vacuuming. Carpet setting and height adjustment appears to be working OK, roll is clean and turns easily when out. Also turns easily until it engages the carpet. Self propel function works just fine.


... Hoover U6485900 Bagged Upright Vacuum

My dyson dc07 brush bar seems to be only spinning at half speed. Leaves three light streaks in the vacuum marks like somethings just dragging. Brush bar is clear and filters are clean. Seems like there's slipping somewhere.


The belt is stretch and so it is slipping on the motor shaft. You need to change the belt. Here is a link for the\015\012instructions on how to change the belt and a link for the belt you need: ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Bissell lift off vacuum about 4yrs old. Extremely noisy. OK until before Christmas but getting worse every time it's used. Washable filters washed, HEPA filter replaced. brush bar cleaned of every scrap, hose empty,everything that can be cleared has been. Noise high pitched, screeching and can only bear to use it for a few seconds at a time. Suction OK.


Sounds like a bad motor bearing. If it is, then you would have to replace it. Could be the brush roll, did you check the ends to make sure they turn easily? ... Vacuums

When switching the vacuum (DC17 Animal) over to the hard surface setting (so the beater brush is not spinning), the vacuum shuts off. I cleaned the dust bin and checked the filter. I also cleared the beater brush of hair or debris that was wrapped around it. It still shuts off. Ideas? Thanks.


The drive belt has probably broken. You can get a replacement belt here:Dyson DC17 Belt ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

I have a Dyson DC14 It started making a high pitched squeel so I took the filters out and cleaned them and i checked all places that pull out on the vacume to see if there was anything clogged. I also cleaned the roller brush. but when I turned it on, after a couple of seconds the sound came back again. can you help


Sounds like motor bearings are gone .... sorry. ... Dyson Vacuums

Low suction I have a Hoover central vacuum system. I've reset the fuse box, checked the fuses, all of the lines are clear and there are no holes for escaped air to travel out. The filter has been cleaned as well. The vac works well with high suction when hooked directly to the unit, however when using any of the indoor connections there is extremely low suction. The machine still turns on so I do not believe it is an electronic issue. I have troubleshooted the issue as best I could and would


... Hoover L2310 GUV Central System Vacuum

Brushes won't rotate. I have cleaned filter on bottom and properly placed the spin mode selector in the correct position.


... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

My Lg Canister vacuum keeps beeping and shutting down even after filters have been cleaned or replaced also air flow is low causing the brush attactment not to work properly


... Vacuums

Roomba 530. All new brushes and gear box clean. Brissel brush does not turn


... iRobot Roomba 560 Robotic Vacuum

I have a DC07 and the brush wasn't rotating and I had no suction at the brush but perfect suction through the hose. I noticed a large build up of dog hair around the brush so I took off the cover plate and removed all the hair, cleaned inside the floor/brush housing and cleaned out the hose. I also cleaned the filter and removed the other air access cover and made sure that they were clear. I put everything back and the brush still doesn't turn and there is still no suction through the bottom


Hi and welcome to FixYa. I am Kelly. \015\012\015\012Here is a link that can assist you in your quest for the missing suction: \015\012\015\012 ... Dyson DC07 Bagless Upright Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1279 seconds