Having problems with your Hoover SteamVac F5914-900 SpinScrub Upright Vacuum ?

I have a hoover f5914-900 steam vac.. and I was wondering if there's a way to take apart the spin brushes to get them cleaned out well. I loaned it to family, and the brushes came back extremely soiled and not spinning.


Answers :

The brush block may be removed from the base for rinsing.
\015\012Yes, you can CAREFULLY disassemble the brush block assembly by releasing each of three latches that hold each of the clear gear covers to the main block. A small screwdriver is used to GENTLY lift each tab, one at a time. Pay attention to what position the special gear is at that has the drive pin (1/4 inch square drive) for correct reassembly.
\015\012
\015\012Here is the link to the User Manual that shows how to remove the brushes from the base.
\015\012
\015\012http://www.hoover.com/pdfs/manuals/F5914900.pdf
Repair Help & Product Troubleshooting for Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a hoover f5914-900 steam vac.. and I was wondering if there's a way to take apart the spin brushes to get them cleaned out well. I loaned it to family, and the brushes came back extremely soiled and not spinning.


The brush block may be removed from the base for rinsing.\015\012Yes, you can CAREFULLY disassemble the brush block assembly by releasing each of three latches that hold each of the clear gear covers to the main block. A small screwdriver is u ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Brushes only work when Dust Bin is removed!! I have cleaned & cleaned this thing! It runs for about 2 mins & stops, says "Clean Brushes"! and now it's very noticeable it's not picking up well... but is picking up a bit. I take the dust bin out, and the brushes spin.... and it has much more power.... and is very clear it is working! But it's useless without the dust bin! LOL It's only 9 months old.... called customer service, but it was the one time it worked just fine! Of course, I thought I'


HI, If the brushes work , without the bin, the problem , the problem could be caused , due the failure at the bin lock mechanism. There is a sensor that checks if the BIN is connected properly or not. This problem is best resolved by getting ... iRobot Roomba 560 Robotic Vacuum

I was vacuuming my room and all of a sudden I hear this loud noise, then notice the roller brush isn't spinning. Thinking too much hair was caught I separated it from the rod and hose to clean it out, but noticed that the roller brush didn't move at all while I was cleaning it. I've cleaned the brush before and it would roll around with little effort, but this time I couldn't move it at all. After removing hair and string I put the vacuum back together and started it up, but the noise continued,


It sounds like if the rod is clean then there is debree inside the roller where the rod fits in too. ... Hoover Platinum Cyclonic Bagless Canister Vacuum With Power Nozzle

I have cleaned & cleaned this thing! It runs for about 2 mins & stops, says "Clean Brushes"! and now it's very noticeable it's not picking up well... but is picking up a bit. I take the dust bin out, and the brushes spin.... and it has much more power.... and is very clear it is working! But it's useless without the dust bin! LOL It's only 9 months old.... called customer service, but it was the one time it worked just fine! Of course, I thought I'd stop here first before calling again! Than


Ok, this is a "Brush Height Adjustment" issue. It will probably work great on a hard surface but on carpet the brushes bog. If you've taken the unit apart already...Sorry....do it again. When you do, you'll see a String which allows the brushes to " ... iRobot Roomba 560 Robotic Vacuum

Kirby sentria My roller brush won't spin belt is not broken I cleaned the Roller brush and put it back it. It put it back but it looks like the sensor balls aren't touching the plastic part underneath. The green light Doesn't turn on either. It was just working and it stop picking up out of nowhere this


... Vacuums

Last time I used by Hoover it worked fine, took brushes out to clean them and now when I try to put them back in they won't snap into place and lock. Looks like all tabs on both sides of the brush piece are there and I spin the brushes for the center spindle to line up but it won't snap into place.


Just slightly turn the brush wheel, The tabs look square, but are just a little different in one direction ... Hoover F7425-900 SteamVac V2 Widepath Upright Vacuum

Clarke scrubbers helo there. on the front brush head assembly the actuator motor that lifts the brushes up and down from the floor has a sleave and a finger that turns the motors on and off. when the head is lowered it comes on and brought back up it turns them off. this assembly controls when the pads start to spin and also determins the downward pressure of the pads affecting the cutting and or cleaning pressure onto the floor. how do i adjust the height at which the motors turn on?? ther


... Clarke Vacuums

Clarke Instructions helo there. on the front brush head assembly the actuator motor that lifts the brushes up and down from the floor has a sleave and a finger that turns the motors on and off. when the head is lowered it comes on and brought back up it turns them off. this assembly controls when the pads start to spin and also determins the downward pressure of the pads affecting the cutting and or cleaning pressure onto the floor. how do i adjust the height at which the motors turn on?? t


... Vacuums

Hello. I took the sole plate of to clean the brushes on my dyson dc14 however the brush part came out and i put it back in but since then whenever i switch it over to carpet setting it makes this really horrible clicking grinding sound its only new have only used it a couple of times.


You really need to take the sole plate back off and make sure the belt is running exactly where it's supposed to go and not looped over a piece of plastic or anything. More important is that you make sure the ends of the brush are seated properly an ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

My roomba spins and moves back and after 2-3 minutes stops and makes the uh oh sound followed by 10-12 beeps I cant say Im sure how many. Some days before stopped cleaning and told me to remove and clean the brushes I did that but then had this problem


\015\012\015\012\015\012\015\012Your bump sensors are malfunctioning. I had the same problem.. The best thing to do is order a repair kit. I ordered mine from EESolutions.ca and it worked great. I'd recommend it. ... iRobot Roomba 530 Robotic Vacuum

I have Hoover Widepath Bagless 12 Amp Windtunnel vacuum. Yesterday I was vacuuming and smelled smoke and it shut itself off. Today I cleaned out the filters (they weren't bad) made sure nothing was obstructing the hoses or the spinning brush part. It turned on for 1 second, smells like smoke somewhere from the bottom and now won't turn back on so I don't know if anything is spinning or not. What can I do to fix this myself?


Hi There,\015\012\015\012When a vacuum cleaner smokes, it is usually only one of two possible problems.\015\012\015\012It could either be that your motor burned up, or that your belts burned. The belts on this particular mod ... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

I have a Dyson DC14 It started making a high pitched squeel so I took the filters out and cleaned them and i checked all places that pull out on the vacume to see if there was anything clogged. I also cleaned the roller brush. but when I turned it on, after a couple of seconds the sound came back again. can you help


Sounds like motor bearings are gone .... sorry. ... Dyson Vacuums

Have Hoover F7452900 spin vac carpet shampooer and brushes won't spin. The screen by the brushes is clean and they are place in position to clean on carpet. I noticed that when I have the brushes out of the machine and turn it on that the white square that is on the base of the machine does not spin--this is where part of the brush connector fastens to make bristles spin.


... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Poor Suction Heya! So I just picked up a used Dyson, but when I vacuum with it, the suction is pretty weak and it spits all kinds of stuff out the back and into my feet. When I pull the hose I have good suction, but in regular mode it hardly picks up anything. The brushes are spinning, and it eventually will clean an area if I go over it again and again. Maybe a clog somewhere? Please tell me that Dysons have better suction than my $50 Dirt Devil! Thanks!


I recently bought a second hand Dyson DC07. Its suction was poor. I removed all the un-clipable pipe bits and to remove any blockage but it all looked clear. The Final Sponge and hepper filter did have a lot of dust in it and the rotating brush was f ... Dyson DC07 Bagless Upright Cyclonic Vacuum

I have a Panasonic MCE6003 vacuum cleaner. I regretfully leant it to a neighbour and it came back full of dog hair and keeps cutting out. I cleaned out the dust container and the main filter but it still kept cutting out after 5 minutes. I decided to unscrew the part with the motor and wash the filter inside.It was all going well until a large rubber washer bit, a piece that looks like the thermostat and a little white button attached to two black wires fell out and now I have no idea how to put


... Panasonic Vacuums

Does not vac carpet well brushes spin and are clean no cloggs and wand works good


It could be that the belt is worn. You can get replacement belts here:Replacement Vacuum Belts ... Vacuums

I have an older model F6056-900 Hoover steamvac Spin Scrub Cleaner. My first problem was that I loaned it out to a friend. Anyway she ran over the hose (used for attachments) with her car. I tried using the cleaner for carpet cleaning this morning but when I tried to put the solution tank into place...its loose...won't snap back in like it used to. When I can get it somewhat in place the solution just complete drains out through the bottom fo the tank. The leak is where the small hole on the bot


... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

We have the pet steam cleaner bissell 12 amp, we tried cleaning off the brush, because the cleaner wasnt sucking up the water sufficently. a screw came out along with the belt roller, and we have no idea how to put the screw or the belt back on.


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

Hoover steamvac spin brush puts out water, won't pull it back up. Checked all parts, no cracks. Cleaned filter.


Check for the front panel duct located on the lower tank front. this is the part you need to remove to attach the hose. also check to make sure the lid is on and secure on the lower tank. remove the lower tank and look on top of the motor cover towar ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

I replaced the belt already, cleaned the roller brushes well & put it all back together then the new belt broke too


Is the brush roll spining if not the belt is slipping and over heating and snaping ... Hoover U5753-900 WindTunnel Bagless Upright Vacuum

My Kenmore 35922 works well on floors, but it recently became very difficult to push on carpet. The brush spins and a local vacuum repair guy wouldn't solve my problem since the vacuum worked fine on his very flat, commercial carpet. What can I do to get my easy to push vacuum back?


Hi dalee196,There are three common reasons why vacuum cleaners are getting hard to push.1. Base is dirty - The base needs to be clean from dirt and tar.2. Height is too low - You might want to consider adjusting th ... Vacuums

Hoover windtunnel Not sure of model number- but brush roller clamps down on carpet being vacuumed and stops spinning regardless of which of the 3 height selections is selected. Can make it work by leveraging the handle down (or back towards me) to keep the cleaning head a little off of the carpet-any suggestions or ideas?


Would suggest the drive belt is stretched and thus is slipping when contact is made with the carpet. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

I have a bissell powerforce bagless turbo. The problem is the brush bar is not spinning. I have cleaned out all the debris on the brush itself, and taken it apart to make sure nothing is blocking the


Sorry to hear you're having difficulty with your vacuum. You may want to have a Qualified Technician at a BISSELL Authorized Service Center inspect your vacuum. Here's a quick link to locating a Service Center. ... Bissell Vacuums

The flexible brush on my unit does not spin. It did 'by accident' pick up a cat poo that didnt make the litter tray while I was out, (and it happily spread it all over the house and skirting boards). I cleaned the unit, removed the base and wiped everything clean. I've unscrewed the flexible brush and cleaned underneath it but it still wont spin. Any suggestions?


... iRobot Roomba 530 Robotic Vacuum

Hoover WindTunnel S3765. The motor spins and the belt turns when I turn the brushes on, and the brushes will spin. The problem is that when I do this on carpet, the brushes stop spinning. As soon as I pull the "head" off the carpet, the brushes spin again. It's almost as if the vacuum suction is too great. I took the head apart and watched the motor turn the metal spindle that the belt rests on, and the belt turns as well.


The belt is stretched and needs replacement.(Belt # 38528036) . The brush is not turning against resistance. ... Hoover Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0750 seconds