Having problems with your Hoover SteamVac F5914-900 SpinScrub Upright Vacuum ?

Brand-new machine, worked perfectly yesterday. Today, will Not **** up solution from carpet.


Answers :

(1) Make sure the lid is sealed to the recovery tank.
\015\012(2) Look under the corner of the tank, where the round pipe meets the base. Is the black rubber ring gasket on the pipe on the base, or did it fall off under the hood? This seals the tank to the motor vacuum.
Repair Help & Product Troubleshooting for Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Brand-new machine, worked perfectly yesterday. Today, will Not **** up solution from carpet.


(1) Make sure the lid is sealed to the recovery tank.\015\012(2) Look under the corner of the tank, where the round pipe meets the base. Is the black rubber ring gasket on the pipe on the base, or did it fall off under the hood? This seals th ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Please please help me! I recently bought an Empisal Celebrity 550 Sewing machine, I've used it maybe 4 times up to now. Yesterday I was sewing with it and everything was working perfectly, today, when I got home, I plugged in the sewing machine and started sewing, just to see that the bottom stitch is completely loose. It's making this loose loops instead of stitches? I didn't change a knob or anything from working with it yesterday to today, so I don't understand how it all of a sudden doesn


... Vacuums

I have a carpet magic steam machine. The pump worked fine yesterday. Today, I cannot get the pump to prime. (The solution resevoir is full.) Is there anything I can do to help prime the pump? Thanks for any help!


... Vacuums

There was no category for sewing machines....so I picked small appliance. When I depress the foot control E1 flashes on the LCD screen. I've followed the steps in the manual but it continues to flash E1. The machine will not operate. This is a brand new machine. I've used it only 3-4 times in the last 2-3 years. It worked perfectly until now.


What make and model of sewing machine do you own ? the more information you provide the easier it will be to assist you . ... Vacuums

1. Bissell Model #7350-C 08249C Carpet Cleaner 2. No soap & water is coming out of machine 3. Worked fine yesterday but isn't working today, we have disconnected it and cleaned all visable places.


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

The solution stick inside the handle needs replaced and I would like a new face plate. I have the model numbers (38458-031 & 37275-011), but can not locate the replacement parts. This machine is more than 10 years old and works like brand new. I can not see throwing it out and want to fix it. Please help me locate these parts. Thank you!


... Hoover Steamvac F5860-900 Vacuum

Wont charge new roomba for xmas. lights on charging unit both flashing but no power in roomba. it worked yesterday when i got it out of the box and did a full clean. i feft it on charge over night ready for the clean today but when i got up no power atall please can you offer a solution. i have held down pock and start - no joy. i have checked the battery connections - no joy please help many thanks caroline


Did you try plugging in 560 driectly to charger then run it? ... iRobot Roomba 560 Robotic Vacuum

I have a DYSON ROOT cycle carpet cleaner. It is cleaned and looked after and is in perfect working order. However, I have been using this machine, with inserted ear plugs, since the day I bought it. The noise is driving me mad! I have never owned such a noisy machine. Do you have a cure for this jet engine noise, or is there no choice but to purchase another machine which is not DYSON?


... Dyson DC08 Cylinder Bagless Canister Cyclonic Vacuum

I purchased a brand new Techno 1000 Fog Machine last Halloween. It worked fine, but once I ran the cleaning fluid through the fog machine only heated up and produced no fog. A year later and now won't even heat up at all, even after replacing the fuse!


... Vacuums

Brushes We have A Proheat Select X2. Brand new, using for the first time, heater works, liquid dispenser works, Power brushes on machine and on extension attachment do not turn. Any thoughts? Thanks gigi2244


If the floor brushes don't turn, there is a motor for that and it maybe bad, On the attchment, vacuum is what turns those brushes, On the tank there is a knob to turn for the floor or hose, is it turned for the right application? other then that, y ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

The brushes won't work and the green shows on the 'TOOL' section, but the machine is in the upright position and should be transferring to the floor section. I have a brand new machine and have only used it once. What is the matter, and what can I do? Billie


What is the maker and model of your vacuum? ... Vacuums

Suction button Although my Hoover Spin scrub is working perfecting dispensing the solution, when I go to suck up the solution from the carpet--I am having problems with the RED suction button that keeps popping up. I have to stop the cleaner and lift up the dirty water container to break the suction. Ive tried cleaning the netting that is encased around it, but still no luck. Any help would be appreciated! Thanks


This happens when the filter on the inside of the lid for the dirty water tank is pushed all of the way up. You need to leave a 1/4 in. gap from the top to the top of the filter ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Hi - my machine works perfect except that it has


I posted this same solution for another inquiry but I will state it again in case you can't find it. I tried everything as well to try and get my machine (only used twice) to **** up the dirty water and I couldnt' fix the problem - there was no suct ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

I have a Bissell Proheat 2x cleaner which has worked perfectly on every occasion. Today I filled the machine as usual with water and formula and switched on, the motor ran, the lights were on and the brushes rotated but upon pressing the spray trigger no water or formula was released. I have cleaned the jets underneath and also followed instructions to release any airlock. It still wont release the water/formula. What else can I do? Thanks Charles


Please check the following with liquid in both tanks.\015\012 \015\012- Check to see if the machine will spray through the hose with the setting on tools. If it does, the pump is fine. Continue troubleshooting.\015\012- ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

I have a Hoover U3330 001 upright vacuum, while using it today the power suddenly cut out and it stopped working. I have replaced the fuse with a new and tested fuse, but the machine will still not power up. please can you help?


... Hoover Vacuums

Little green machine pro heat pet the collection tank wasn't collection and dirty water was coming out of the bottom. i took it apart, cleaned it up and put a new "duckbill" gasket in. then it quit spraying, but i think i got that working again. now after i spray and get a good foam on the carpet, i switch to suction and it seems very weak. i can see the water moving (trickling) from the head into the hose but it is not reaching the collection tank -- actually, i am not sure where its goin


... Bissell THE BISSELL LITTLE GREEN MACHINE Vacuum

I purchased a brand new Eureka Pet vacuum, sorry don't know exact name but it the one that has the self cleaning duster on it. Last night I used the vacuum on my carpet, it was working fine until I accidently sucked up the corner of a scarf that was hanging off a couch. I shut the vacuum off, pulled out the scarf and and resumed vacuuming. Much to my dismay the suction on the vacuum had ceased. Can you tell me if there is a reset button on the vacuum? The vacuum does not appear to be damage


If the motor is running, there should be suction. Possible problems depend on whether it's a canister or upright and are:\015\012A clog in the hose, UR or canister. Detach hose. Drop small coin in one end and lift hose causing it to roll out ... Eureka Vacuums

How does it work I have the machine an no instructions do i have to buy cleaner solution? and can I use on carpet


The manual can be found here:\015\012http://ec1.images-amazon.com/media/i3d/01/A/man-migrate/MANUAL000074560.pdf ... Bissell 9200 Upright Vacuum

We have bissell pro heat and I have put new belts on and took off the top plastic cover I blew out the lines and I still can't get it to pump water or solution. The red little spinner flow indicater does'nt get water, if I pour water into it it runs out the front. I guess I don't know what else to do. The machine worked fine the last time we used it about 6 months ago. Any suggesttions?


Did you check and make sure the belt is still on right? They do come off from time to time.There are like 6 long screws holding the top cover to the bottom. The are real pain in the behind to put back together once you take them off. T ... Bissell Vacuums

On a plush carpet, the machine is not picking up correctly on any height setting. The agitator is sporadic in spinning. The agitator belt is brand new.


Replace the rubber belt that should fix it if not let me know ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

I have a bissell proheat 2?X carpet cleaner, the solution and water does not spray out on the upright machine, but the hand held one is working. How do I fix this please.


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

No spray I have a proheat cleaner. The problem is there isn't any solution when I press the trigger on the handle to use the machine to clean a whole carpet yet if I use the handheld unit it works a treat. I have tried all the remedies in the manual.


\015\012Here are 3 common things that causes this problem:\015\012\015\012• clogged spray tips \015\012• defective solenoid valve in the base \015\012• defective trigger microswitch in upper handle ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

The carpet cleaner comes on and the heat source is working in it, but the machine is not dispensing the water and cleaning solution. It does have consistant suction. What could cause this type of problem?


Most likely a bad belt you might think it looks good but i'd say thats your prob after you replace it you should be fine if not we can go deeper ... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

Bought an PlayStation 2 at our youngest dauthers 9 year birthday together with an dance mat. Caused by an accident we had to buy a new remote contol for some years ago and we chosed your URC-3445. We can't get it to work. How do we get to AV-chanel throughtout your device? There must be a solution at our problem. Please help ....! Her anniversery is unfortunally today!!! Our TV is an rater old Tandberg modell: TVF2915NT Please...


Go to menu settings, find channel edit or add/delete, turn channel to input or a/v channel, select add channel and then your good. You should now be able to use the ps2. You can also hook them up through vcr and use the vcr input/av channel. and then ... Vacuums

My hoover carpet cleaner does not extract water. The brushes stopped turning since more than a month and now it doesn't extract any water. The engine is turning on but it does not work properly. I've checked for the solutions to this problem in the manual but any of the causes listed there apply to my machine. Thanks for your help.


... Hoover F5826-900 SteamVac Upright Wet Washer
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0863 seconds