Having problems with your Hoover SteamVac F5914-900 SpinScrub Upright Vacuum ?

My hoover steam vacs brushes will not turn . could there be a belt broken? I have misplaced the manual


Answers :

For the manual:
\015\012http://www.hoover.com/pdfs/manuals/F5914900.pdf
\015\012
\015\012For the brushes:
\015\012(1) Assure the Brush Control on the hood is NOT set to the OFF position.
\015\012(2) Remove the brush assembly by pulling/unlatching it from base on each side.
\015\012(3) Does one of the brushes have the drive pin present? It should be about ¼ inch square, and two inches long. It attaches the brushes to the drive mechanism.
\015\012(4) Remove and clean the intake filter. One the base of the cleaner, behind the brushes, squeeze the two red abs together and pull the panel down to access the screen. Clean the hair/debris off the screen and reassemble.
\015\012
\015\012The gear box that drives the brushes is driven by vacuum air, running the turbine inside.
\015\012There are no belts, just direct drive.
\015\012
Repair Help & Product Troubleshooting for Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My hoover steam vacs brushes will not turn . could there be a belt broken? I have misplaced the manual


For the manual:\015\012http://www.hoover.com/pdfs/manuals/F5914900.pdf\015\012\015\012For the brushes:\015\012(1) Ass ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Brushes Hoover steam vac f5906-900 .can,t get the brushes to work. Is there a belt that could have broke


This machine has no belts. There is an air driven turbine that propels the brushes. If you look under the little glass window at the left front corner of the machine, there is an intake screen just above the indicator dial. That screen is there to ke ... Hoover F5906-900 Upright Steam Vacuum

Hoover steam vac dual Model # F74310-900 - Brushes won't spin. i've cleaned the little screen per owners manual and still no fix. What else could it be? I can spin the brushes by hand if i remove the assembly.


... Vacuums

The brushes won't spin on my F7220-900 Hoover Steam Vac.. Is there a belt that could have broke and needs a new one??


... Hoover F7220900 SteamVac V2 Upright Vacuum

Good Morning, A friend recently gave me her Hoover windtunnel model U630-900 vacuum. It is a self propelled vac. It comes on but is hard to push and will not really pick up any dust particles on the carpet. It has a funny smell also. I saw where one of you Q & A you said to check the roller brush. I thought maybe a belt may be off or something, but I do not have a manual to know where to begin checking. Could you tell what to check and also if there is anywhere online to download the manua


... Hoover Ultra U6430-900 WindTunnel Bagged Upright Vacuum

Beater brushes not turning on the wife's Hoover Steam Vac model F5905-900. Found one prior ''solution'' stating that it sounded like the belt was bad. That was my original thought, but on checking schematics and trying to find part numbers at Sears Parts Direct and at Hoover, it does not appear the F5905-900 steam vac HAS any belts to begin with. What's next??


This one I can tell you about from personal experience with that generation Hoover Steam Vac. After using it about 7 or 8 times my brushes stopped turning also.I disassembled it (kind of like disassembling a Chinese puzzle box) and found ... Hoover F5905-900 Vacuum

Miele White Star SEB 204, powerhead stopped spinning. brushes are clear of debris, belt (#3854940) is not broken. Could belt be stretched so that brush head does not spin?


Yes, most likely the belt has stretch. Flat belts do this after a short time and need to be replaced when problems start with the brush roll not wanting to turn. Also check the brush roll, make sure that the ends turn freely, if not, then replace i ... Miele Vacuums

I replaced the belt on my Dirt Devil Featherlite Bagless Vacuum and the brush roller rubs and makes a very loud noise when turned on. I have gone exactly by the manual instructions and made sure the belt and end caps were on correctly, but the bristles still rub the back and it makes a very loud noise. Without the brush roller in the vacuum, it sounds and runs normal. What could the problem be?


Http://www.geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=561283\015\012Generic problem for all Vacuums\015\012I replaced the belt on\015\012Posted by piggyt ... Vacuums

Brushes wotn spin,belt not broken,cog that drives the belt is not spinning.When I turn the brushes manually I can occaisionally feel it grabbing for a a brief second.Could the motor be bad? Is there a way to test the motor.Tahnks


The motor is bad and this is a common problem with this machine. It is engineered very poorly. I would take it back and get a Dirt Devil Platinum Force machine. They have a great track record. ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Bissell 8920 proheat x2 brushes not turning i only noticed this after i finished cleaning.. or kinda cleaning because of the brushes ntot turning.. water comes out fine suction is fine but its not scrubbing so its not as clean as it could be. manual part works well water coming out hot. I did take it apart and cleaned off all the hairs in hopes maybe that was it.. put it together still nothing.. No idea how the belts should look onit and i cant find a picture or a video showing how belts look o


Hello,\015\012\015\012Here's a link to a very helpful video that shows you step by step on how to access and replace the belt on your machine. When the brushes stop spinning, but the rest of the machine works fine, this is a tell-tale ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

A small belt fell from underneath my bissell steam cleaner and I notice the brushes no longer rotate when I purchase the part where does it go? I tried turning it up side down to find out where it came from don't know because there is a compartment for the belt access but that particular bet is not broken. It's a very thin belt I can not make out the number located on the belt please help.


If you are unsure about where it goes it may have a diagram in the owners manual. When you say you saw a belt in a compartment are you sure that it is not an extra belt you are seeing as they often give an extra in the machine kept in a compartment l ... Bissell 1697-7 Powersteamer Pro Deluxe Vacuum

My Hoover steam vac spin scrub model 4060-900 brushes are not spinning and I have lost the manual. Any ideas. Thanks. [email protected]


The problem I found with one a neighbor was tossing out is the bearings in the part that drives the brushes were stuck. Lubing them up solved the problem, but took a bit of work to get into. This also provides a good chance to clean the crud out of ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Dyson dc07 The rotating brush on the bottom of my vacuum was filled with strings. I removed the brush by undoing all yellow plastic screws from plate. Removed all strings and replaced as best I could and it was hard to get the brush back in and the belt around it. I dont have my manual but it fits so it should be correct....? Right? No, not true, because when I turn it on and try to and vacuum (by lower canister with foot release) it makes that terrible ratching sound). Please help


The loud ratching is a warning to tell you that there is something stopping the roller bar from rotating this is a very common thing lay the machine on the floor front side down take off the bottom plate and just check the belt is in the centre of th ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Bissell Power Track Cyclonic Upright Bagless Vacuum.. ..The spin brush works laying down....when upright it won't spin! I cleaned any and all hair from the roller....belt is not broken....but do I need a new belt though? The vac is a few years old bever replaced the belt yet.


You need a new belt. ... Vacuums

We seem to have lost our manual to our Hoover Steam Vac V Dual with rinse, Model F 7220 - 900 and were told by Hoover Rep. that we could download it from this website. How do we do that? I don't see an option for downloading manuals. Thank You, Kathy Crawford


... Hoover Vacuums

I have a Hoover SteamVac Carpet Cleaner with Clean Surge. I lent it to my mother who used it without the brush attached underneath. Now it doesn?t **** up water and the brushes don?t turn. Any idea what would?ve broken? Is there a belt that would have burned out? The motor? Anthing I could fix myself, or would I need service for this?


If you go to this URL:\015\012\015\012http://www.vacpartswarehouse.com/Hoover-F7452-s/811.htm\015\012\015\012you will an exploded view of your Hoover. By going down the pictures you will be able to see the internal parts of the unit and ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

The brush ends where they are screwed to the frame underneath have broken off. Was wondering if I could get another brush for our Hoover/Steam Vac Dual Action, model/F5826-900, series/H71, household type.


... Hoover F5826-900 SteamVac Upright Wet Washer

I need instructions on replacing the belt that drives the brushes on a Bissell powersteamer pro deluxe carpet cleaner. Could the broken belt have anything to do with the suction of the cleaner?


Here is a link to the belts you need and a link to the manual:Bissell 1697-7 Manual and Replacement Belts ... Bissell 1697-7 Powersteamer Pro Deluxe Vacuum

My Steam Vac does not pick up the water from the carpet why? When I pull the Vac backwards to **** up the water it sucks it up sometimes and sometimes it doesn't Is there a manual I can get I seem to have misplaced mine.


Ebay,google,or the manufacturers website they usually have downloadable manuals... ... Hoover F5858-920 SteamVac Wet/Dry Vacuum

My hoover u8130-900 roller brush won't turn. It does't appear to have a belt. What could it be? If it does have a belt, I can't find it and the manual doesn't mention it.


... Hoover V2 U8130-900 WindTunnel Bagless Upright Vacuum

Need the manual on how to run (put together and all) the hoover steam vac v2 (widepath) with auto rinse) we tried today and when we leaned it back (so we could run it on the carpet) water started pouring out all over the machine and got the carpet (like flooded) wet :( this one was me mom's and she passed on approx 2 1/2 years :( she always kept the manuals for everything but we caint find this one :( ... thnx


God Bless Your Mom.\015\012\015\012Hope this was helpfull to you. Sawdust46\015\012\015\012http://www.hoover.com/pdfs/manuals/F7411900.p ... Vacuums

Brushes on hoover deluxe steam vac cvarpet cleaner are not rotating. Took out the brush assy and drive spins slowly but with little torque. Cannot seem to open the bottom to see if belt or direct drive..something wrong with drive mechanism for 5 brsuhes


(1) Assure the brush shut off lever on the hood is not set to the off position. \015\012(2) Is there still a square pin standing up from the one drive brush? It should be 1/4 square, and about two inches tall. That pin is the drive from the ... Hoover F5866-900 SteamVac Deluxe Wet/Dry Vacuum

Roller Brush How do I install the roller brush. I didn't pay attention when I removed it and now when I attempt to vacuum my low carpet it doesn't seem to be working. The green light on the head of the vacuum goes out when I click it down to the floor. It didn't used to do that. Plus I think I smell something burning. Could the belt be broken?


Try a new belt. The ends of the brushroller are different sizes, so you can't put it in backwards. There are numbers and notches on the ends of the brushroll. These notches/numbers need to match on both sides when installing it. (probably need b ... Kirby Ultimate G Bagged Upright Vacuum

My machine (Hoover Wind Tunnel - bagless) is only 1 yr. old. The agitator brush doesn't turn all the time. I know it's not supposed to turn when in the upright position. However, it only seems to work when I have the setting on high. When I stop, but have not put the machine in the upright position, it stops again and then slowly starts moving. Could the V-belt be worn out already? In the owner's manual it states that this belt is not normally replaced. The exact same thing happened with my old


Sounds like you should do two things:\015\0121- Remove and clean the beater brush of all debris as best you can. At the end of the brush you will see a hard rubber piece, at both ends, that holds it in place in the body of the vacuum.\015\012Add som ... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

Brushes dont spin on Hoover Steam Vac Model F5919-900


... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0953 seconds