Having problems with your Hoover SteamVac F5914-900 SpinScrub Upright Vacuum ?

The brushes are not spinning - Hoover SteamVac F5914-900 SpinScrub Upright Vacuum


Answers :

Greetings from GoVacuum.com,

It sounds as if your brushes are either clogged with debris, or your turbine that drives the brushes have gone bad. The first thing you should check is whether the brush selector knob is turned to the on position.



You may also purchase any of the supplies that you need directly available on our website http://www.govacuum.com

Here's the diagnosis to your Hoover SteamVac:
Greetings from GoVacuum,

The Hoover SteamVac's are notorious for this exact problem. There are several things that can be causing this probelm.

First, what you'll need to do is take the brush block out of the machine. To do this there are 4 clips on the brush block. You will need to turn the machine upside down, and pull down on the brush block to where it won't pull out any farther. There are 4 clips, 2 on top, and 2 on the rear of the brushes. (See picture, I have circled one of the clips in red). Simply press these clips at the same time, and pull the brush block out of the machine. I'd say that 60% of the time that I see this problem, the main issue is that the brushes just need to be cleaned. If you have pets in the home, a lot of the time the pet hair will just be lodged inside the brushes, will prevent them from spinning. Use a pressurized water hose with a spray nozzle is ideal) and spray each brush with water to dislodge any pet hair.
\015\012
\015\012You should be able to get these brushes spinning when you spray them. Spray each brush until the brushes are spinning pretty fast. Re-insert the brushes into the machine, and test to see if the cleaning has fixed your problem. If the cleaning still fails to fix the problem, take the brushes back out of the machine.

One you have the brushes out of the machine, the first thing you should look at the brush stem that goes into the turbine inside the machine. This is the green pole pictured in middle of the brush block. Examine this pole to determine if the top of it has broken off. It should exactly how the picture belwo shows it. Make sure that the plastic has not broken.

If the pole has broken, you will simply need to replace the brush block. If the pole is not damaged, the next thing to try is to turn the machine on while you have the brushes out. Look inside the machine, where the pole goes into the turbine (also important, make sure the switch for the brushes is turned to "Rotating Brush Speed Hi), this female receptacle should spin when the machine is turned on. It is important the try this when the foot pedal is released, and the handle down, and not in the upright position, as there is an internal switch that shuts the brushes off when the machine is in the upright position.

If you notice that the female receptacle where the brush pole is inserted is spinning, then your turbine is fine. If this part is not spinning, then most likely you will need to replace your turbine.

I hope this helps you with your problem. If not, please feel free to email me at , and I'd be happy to walk you through the diagnosing. I also can provide you with a blown up parts schematic to your machine, please just get the model number off the back of the machine and provide, and provide me with the full model number. I do carry all parts for your machine, and would be happy to provide any help on the repair you need.

I tried uploading the pictures to this solution, however Fixya will not allow the pictures because they are too big. Please email me, and I'll send you the pictures.

Chris Jones
GoVacuum.com
d6c0881.jpg232c8b0.jpgadc2d4f.jpgb64e530.jpg
Repair Help & Product Troubleshooting for Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

The spin scrub brushes do not spin. - Hoover SteamVac F5914-900 SpinScrub Upright Vacuum


Try this: Make sure the setting is set to floor, then remove the little window (you might need a flat screwdriver to "pry" it up) and clean off the filter. If there is a blockage, the brushes will not spin! I hope this helps, if so, please give fe ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Scrubber brush does not spin - Hoover SteamVac F5914-900 SpinScrub Upright Vacuum


There is a plastic piece on the back of the block brush (spin scrubbers) these wear out or break. You may need to replace the block brush. You can find the parts and a schematic below follow the link. Please don't forget to give positive feedback ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Brushes are not spinning - Hoover SteamVac F5914-900 SpinScrub Upright Vacuum


Remove the brushes from the base of the unit by pulling down and unlatching at ends. Is there a drive pin present? The pin will be a 1/4 inch square pin, about two inches long. It engages to the drive mechanism.\015\012\015\012Second: ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Brushes don;t spin - Hoover SteamVac F5914-900 SpinScrub Upright Vacuum


First remember that the speed switch must be set to carpet. The handle must also be tipped back. If this is not the problem, you probably have a bad turbine assembly. Remove the brush assembly and insert a flat screwdriver into the square hole that t ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Spin brush isn't working - Hoover SteamVac F5914-900 SpinScrub Upright Vacuum


... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

My brushes stopped spinning. What do I do? - Hoover SteamVac F5914-900 SpinScrub Upright Vacuum


Sounds like the brush belts has snapped and needs replacing, you should be able to get a replacement at most electrical stores, just take the make and model number with you. ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

The brushes are not spinning - Hoover SteamVac F5914-900 SpinScrub Upright Vacuum


Greetings from GoVacuum.com,It sounds as if your brushes are either clogged with debris, or your turbine that drives the brushes have gone bad. The first thing you should check is whether the brush selector knob is turned to the on positi ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Brushes not spinning - Hoover SteamVac F5914-900 SpinScrub Upright Vacuum


Solution: Remove the clear plastic cover located in front of the brush control switch (I used a butter knife). Locate the small screen and remove the dirt and hair from it with your fingernail or an old tooth brush. Restore the cover and you should b ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Brushes won't spin - Hoover SteamVac F5914-900 SpinScrub Upright Vacuum


Hello, and thanks for using FixYa. I'm guessing that the brushes have become jammed, there is most likely hair, or something similar that has build up inside and its preventing the brushes from spinning. Make sure you turn off / unplug t ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Brushes are not spinning - Hoover SteamVac F5914-900 SpinScrub Upright Vacuum


Hi There,\015\012\015\012When the brush block assembly on a Hoover SteamVac doesn't spin, it can mean really one of three things. First, the brushes are clogged with debris that is not allowing the brushes to turn, second the brush bloc ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Brushes not spinning - Hoover SteamVac F5914-900 SpinScrub Upright Vacuum


... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

My brushes stopped spinning. what do i do? - Hoover SteamVac F5914-900 SpinScrub Upright Vacuum


You simply just need to change your belt. This models uses Hoover belt # 40201160 and can be found at www.vacbelts.com. ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

The rotary spin brushes will not turn - Hoover SteamVac F5914-900 SpinScrub Upright Vacuum


Belt either came off or broke ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

The brushes on the unit do not spin. - Hoover SteamVac F5914-900 SpinScrub Upright Vacuum


Try to clean the filter under the machine or the filter behind the clear plastic, were you see the hypnotic disc sprin that lets you know that the brushes are spinning. To remove : the plastic piece that looks like a triangle, ( were the indicator is ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

My brushes are not spinning - Hoover SteamVac F5914-900 SpinScrub Upright Vacuum


Hi There,There could be several reasons why your brushes are not spinning. Here's a step by step diagnosis guide so that you may check to see first what is causing them to stop spinning. If you diagnosis this and find th ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Brushes don't spin - Hoover SteamVac F5914-900 SpinScrub Upright Vacuum


(1) Assure the Brush Control on the hood is NOT set to the OFF position.\015\012(2) Remove the brush assembly by pulling/unlatching it from base on each side.\015\012(3) Does one of the brushes ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

The brushes are not spinning - Hoover SteamVac F5914-900 SpinScrub Upright Vacuum


Replaced belt ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Brushes do not spin - Hoover SteamVac F5914-900 SpinScrub Upright Vacuum


(1) Assure the Brush Control on the hood is NOT set to the OFF position.\015\012(2) Remove the brush assembly by pulling/unlatching it from base on each side.\015\012(3) Does one of the brushes ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Brushes do not spin and not sucking up water - Hoover SteamVac F5914-900 SpinScrub Upright Vacuum


... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

The brushes on my steam vac don't spin - Hoover SteamVac F5914-900 SpinScrub Upright Vacuum


(1) Assure the Brush Control on the hood is NOT set to the OFF position.\015\012(2) Remove the brush assembly by pulling/unlatching it from base on each side.\015\012(3) Does one of the brushes ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

My brushes are not spinning - Hoover SteamVac F5914-900 SpinScrub Upright Vacuum


You probably have a break in the wiring somewhere or you got water in the motor. if there is a break replace all the wires and solder all the connections, if it still doesn't work start replacing switches and other components. if you got water in th ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

The brushes will not spin - Hoover SteamVac F5914-900 SpinScrub Upright Vacuum


The belt maybe broke take a look to see if it is you maybe able to get replacement belt at walmart!!! :) amtnng ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

How to remove a single brush from brush rack - Hoover SteamVac F5914-900 SpinScrub Upright Vacuum


... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Hoover spin scrub f5915900 belt replacement - Hoover SteamVac F5914-900 SpinScrub Upright Vacuum


... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Spinscrub F 7412-900 brushes wont turn - Hoover SteamVac F5914-900 SpinScrub Upright Vacuum


... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1251 seconds