Having problems with your Hoover SteamVac F5914-900 SpinScrub Upright Vacuum ?

The scrub brushes are not spinning, mod.f 5869-900


Answers :

NEED REPLACED TURBINE ASSEMBLY-SVPart Number :90001355
Repair Help & Product Troubleshooting for Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Brand new Hoover Max Extract Deep Cleaner brushes won't turn. Read manual. Checked filters - all clear. Set Spin Scrub Mode Selector to a scrub setting. Brushes still won,t turn. However the brushes on the Spin Scrub hand tool rotate.


... Vacuums

My hoover spin scrub brushes stopped spinning and i have cleaned intake filter and tried to turn the thing that spins it...when brushes are off the hole turns then as soon as i connect brushes the brushes will not turn what else can i do!!???


... Vacuums

Have a spin scrub a couple of years old. Have used it maybe 5-6 times and the green brushes only spin if you take the tanks off and set the machine upside down and push the brushes toward the machine... the second you stand the machine up they quit spinning.


Repace the belt ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

My hoover spin scrub machine has stopped scrubbing. It still dispenses and pulls up the water, but the brushes don't move. I've checked the on off button for brush control and cycled it to off and back on, but no movement out of the brushes.


There is a filter on the front right hand side of my F5871-900 Hoover. If you remove the plastic covering and clean that filter (wet finger may do), you're Hoover will begin spinning again! ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Spin-scrub brushes do not spin


Hello. there is a little window by the brush control. if you open it up, you can see that there is maybe some lint covering it. scrape that off, and try again. make sure your lever is set to brushes and realease the handle release. if this doesn't ... Hoover F7431-900 SteamVac Vacuum

My Hoover steam vac spin scrub model 4060-900 brushes are not spinning and I have lost the manual. Any ideas. Thanks. [email protected]


The problem I found with one a neighbor was tossing out is the bearings in the part that drives the brushes were stuck. Lubing them up solved the problem, but took a bit of work to get into. This also provides a good chance to clean the crud out of ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Miele, Flamenco II. 2 probs. 1. the head brush is not turning when I put it on the floor. If I pick it up to look inside...the brush is spinning fast..I put it down on the floor...the head does not spin at all. 2. The suction power has dropped significantly. The suction used to be so intense, the head would **** itself to my floor and hold on...now, hardly any suction at all.


Sounds like the belt is not on correctly on the beater brush or the belt is worned out now for the suction check filters or bags that need to be empty or clean ... Miele Vacuums

Why won"t the brushes on my Hoover spin scrub spin?


... Hoover Steam Vac Dual V w/ SpinScrub Vacuum

HooverSpin Scrub and the brushes always stop spinning.


Greetings from GoVacuum,The Hoover SteamVac's are notorious for this exact problem. There are several things that can be causing this probelm.First, what you'll need to do is take the brush block out of the machine. To do this ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

LlllSteam vac ws working very well--shilfted to using hand vac on furniture--when I shiftead back to wanting to use the floor vacuum using the 6 brushes and the floor vac system, the r6 rotaty brushes will not turn or function. What do IO havae to do to get them to turn and function? The lever on the side ils set for carpet terrain. What do I do now to get brushed to turn and scrub as they should and did previously. James Yerges 1'630-232-2798 JMYerges&comcast.net


What is the exact model number of that unit. There are several with that name. The only things that it could be are the handle mechanism that activates the brushes or the indicator is not working nad the level that selects the brushes is not working. ... Hoover Vacuums

I have a Hoover steamvac Dual V carpet cleaner Model No. F7427-900. This is a spin scrub upright. My brushes will not work. We think the white square that the brushes fit up into in the center of the brushs is not turning. Can you help me.


You are on the right track! Place a screwdriver (flatbladed) into the white drive square and try to turn it. If it is locked up the drive assembly is your problem. It is very common for these parts to lock up because of the moisture involved with ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Spin Scrub Brushes won't turn


If the brushes quit spinning, either the brush block shaft that goes into the turbine broke off, or the turbine is bad. This unit is tricky to take apart and then put back together again. But pull the brush asm off, then start taking out screws. B ... Hoover H3030 FloorMate SpinScrub 500 Upright Wet/Dry Vacuum

Help. The brushes on my Steam Vac Spin Scrub


If you don't have the user's manual for the machine, here it is:www.thinkvacuums.com/pdf/uprights/Hoover_F5914900.pdfCheck your system for any obstructions that could possibly causing the problem. Also, remove the brushes and see if ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

The scrub brushes dont spin anymore


The brushes are turning by an air driven turbine. The turbine has a \012pivot bushing made of steel inside of it that gets rusty because of the \012water that is running through it. The turbine gear will have to be \012replaced.\012 You can access ... Hoover F7425-900 SteamVac V2 Widepath Upright Vacuum

Hoover Spin Scrub model # F7410-900. The brushes will not spin.


Take the brush block out, is the shaft still on it or did it break off, if it broke off, then replace the brush block. If it is there and you can turn the brushes by hand, then the turbine is bad. Sometimes you can clean it out, most time you have ... Vacuums

I have a Hoover spin scrub carpet cleaner and the brushes won't spin?


... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Hoover FH50044 spin scrub. Brushes won't turn. All is clean. Brushes turn by hand when on the machine. Any help.


... Vacuums

Hoover spin scrub brushes won't spin


... Hoover SteamVac F5912-900 Spin Scrub TurboPower Carpet Cleaner

The spin scrub brushes do not spin. - Hoover SteamVac F5914-900 SpinScrub Upright Vacuum


Try this: Make sure the setting is set to floor, then remove the little window (you might need a flat screwdriver to "pry" it up) and clean off the filter. If there is a blockage, the brushes will not spin! I hope this helps, if so, please give fe ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

H300 brushes won't stop spinning even though I switch it from "wet scrub" to "wet/dry pickup" and is leaving streaks on the floor. I have already ordered a new squeege, but that won't take care of the non-stop brush problem. Any suggestions?


I have found that the plastic piece on mine is wore out and slips when the trigger is pulled back. If you look underneath the dirty tank, you will see the black plastic pieces that over lap. I took a wiretie/zip strip and placed it around the spot ... Hoover Floormate H3000 Upright Wet/Dry Vacuum

My spin scrub brushes don't spin at all. - Hoover F7425-900 SteamVac V2 Widepath Upright Vacuum


Check that the belt that spins the brushes is not broken, also that the\015\012gear that drives the belt is turning.\015\012\015\012Tom ... Hoover F7425-900 SteamVac V2 Widepath Upright Vacuum

I have Hoover Widepath Bagless 12 Amp Windtunnel vacuum. Yesterday I was vacuuming and smelled smoke and it shut itself off. Today I cleaned out the filters (they weren't bad) made sure nothing was obstructing the hoses or the spinning brush part. It turned on for 1 second, smells like smoke somewhere from the bottom and now won't turn back on so I don't know if anything is spinning or not. What can I do to fix this myself?


Hi There,\015\012\015\012When a vacuum cleaner smokes, it is usually only one of two possible problems.\015\012\015\012It could either be that your motor burned up, or that your belts burned. The belts on this particular mod ... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

My Hoover spin/scrub floor cleaner has stopped scrubbing- the brushes spin for a few seconds right after turning it on, then stop until I turn it off and then on again. How can I fix this? I do not have a lot of money. I have taken off and cleaned the brushes and bottom vacuum opening.


Hi giacoma11,The common cause for this problem is the belt of your vacuum. It could be that the belt came loose or already worn out and needs replacement. To check if the belt is loose all you need to do is unscrew the bottom of the vacuu ... Hoover H3060 FloorMate SpinScrub 800 Upright Wet/Dry Vacuum

Hoover spin scrub brushes won't turn


... Vacuums

I have used my Steam Vac for carpeting, but until today, had never tried cleaning upholstery with the spin-scrub brush. I spent a miserable afternoon trying to control the spray, which seemed to go everywhere AROUND the furniture, but not ON the furniture! Additionally, I never did get the water into the recovery tank, despite many attempts to connect and re-connect the hoses and recovery tank/lid.


I can sympathize. My vac came with two handheld attachments. I have better luck with the handheld attachment that doesn't have the spin-scrub pads. To keep the water from going all over the place, you need to keep the part the you hold only about 1 ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0467 seconds