Having problems with your Hoover SteamVac F5914-900 SpinScrub Upright Vacuum ?

The brushes stopped rotating is there a reset button or is it jammed


Answers :

Repair Help & Product Troubleshooting for Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

The brushes stopped rotating is there a reset button or is it jammed


This should help you:\015\012http://www.fixya.com/support/r4530769-diagnosis_fix_hoover_steamvacs_when ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Kenmore 116.23513301 Motor runs, but the brush will not rotate. Every time I hit the overload reset button, it will rotate for about a second then stop. I replaced the belt and cleaned around the brush, but the brush still will not rotate. Any help you can give me would be greatly appreciated.


If the motor on the power brush is running the belt is bad, if the motor on the power brush only runs when you push the overload, the overload is bad. ... Kenmore 22812 Bagged Canister Vacuum

Reset button The drive belt on my machine broke. They sent me a new one and I installed it, I think, correctly. It still won't engage and rotate the brushes. I can't find a reset button, but I suspect it needs to be reset. Where is the button? Theresa


Do the brush rolls turn ok? The brush roll motor may be bad.\015\012\015\012 ... Bissell 9400 ProHeat Upright Wet/Dry Vacuum

Now that I just fixed my Lux Legacy canister vacuum, I need help on my other Electrolux Regency Series upright! The vacuum works fine but the rotating brush does not work and the brush motor does not turn on. Tried cleaning the brush and hitting hte reset button to no avail. This upright has a triple setting switch and I checked the each of the wires seem to be attached. Tried rotating the brush by hand and it would not budge. Was going to "encourage" the brush to turn with a set of articula


There are a couple rectangular holes on the bottom of the power nozzle, beside the wheels. These have tabs in them that need released with a standard screwdriver. \015\012 ... Vacuums

The brushroll on my dirt devil (vax X3) was caught o the curtain, and now the reset button will not reset the brush. the power comes on for the brush, but the brush will not rotate. What can i di to fix this problem


I didn't find the reset button until I took all the screws out and then couldn't separate it. Good luck! ... VAX Appliances Vax X3 Bagless Upright Vacuum

Agitator stopped rotating, has checked for clogs, cleaned agitator, and pushed reset button, but still not rotating. Any ideas?


Try changing the belt ... Vacuums

While operating machine, brush does not rotate. Button is pushed in, all hair cleaned off brush. Is there a reset button? Where is it located?


Likely the wires are broken under the left hand cover not a difficult fix. Unplug the machine and remove the 4 torx screws and an access panel at the side of the ball. replace wires with new or re-connect with a splice. ensure wires are long enoug ... Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum

Dc25 brush button stuck on, cannot switch off, brush continuously rotates, reset button does absolutely nothing


... Dyson DC25 All Floors Bagless Upright Vacuum

The rotator brush stopped turning. it turns fine


The brush roll will only spin when your handle is not in the locked upright position, once the handle goes upright - the brushroll de-activates ... Kenmore Progressive Bagless Upright with Inteli-Clean SystemVacuum

My roomba goes round in circles. sometimes it stops and moves a centimeter backwards and then again it goes round in circles. if you press the ,,dock'' button it goes back to the station. if you press the ,,clean'' button, again, it goes round in circles.... the machine is cleaned, the sensors aren't covered with dirt, the weels and brushes can rotate freely.... can anybody help me??? thanks in advance franz


Here's the link. IR Bump Sensor Fix ... iRobot Roomba 560 Robotic Vacuum

I have a sharp R898 combination oven, grill and microwave. It has just stopped heating on the microwave setting (I have not tested grill or oven yet) and the tray inside has stopped rotating. Is there a "reset" button or similar please?


... Vacuums

The brush bar on my brand new DC 28 has stopped spinning - it is not clogged with hair, it just stops spinning almost immediately. Is there a reset button?


If there is nothing dragging it down like clogged hair ect then usually this just means the rubber drive belt has either stretched or is too smooth to grip and properlly drive the beater bar brushes. When those happen the belt cannot get a grip and s ... Vacuums

Dyson 28-animal- Power brush stopped working and power light and carpet level buttons all are blinking. Per the instructions vacuum needs reset by turning it off for 30 seconds. However after doing so it does not reset and work. Help!


... Dyson DC28 Animal Bagless Upright Vacuum

I have a kenmore progressive 359235 vacuum with intelliclean. Has been great for about 3 years but now the brush bar has stopped turning. This is a direct drive unit with a circiut breaker reset button on top . The button is not tripped. Any ideas ?


... Kenmore Vacuums

The brushes stop rotating on rugs after a few seconds then button has to be pressed to start rotating again but keeps cutting out


Not sure this is your foolproof solution to the problem, but you might give it a try to see if it solves your problem.\015\012\015\012When the beater brush starts to bind up due to debris it retards the action of the cleaner, sometimes to the p ... Dyson Vacuums

I have a Panasonic Performance plus MC-V5217. Something got stuck in the rollers and it stopped spinning. We've cleared the brushes but can't get it to spin. Is there a reset button?


... Vacuums

Stop working. brush was cloged. It there a reset button?


I had a similar thing happen and just got off the phone with dyson. there is a resettable switch on the handle. they told me to start the vacuum in the upright position, put it in the non upright position, then push and hold in the beater bar switc ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Brush on progressive beltless vacuum is not rotating and reset button is not kicked...appreciate some help...steve


Before you replace any parts, I recommend that you unplug the ... Kenmore 31912 Progressive Direct Drive Bagged Upright Vacuum

I have a DC-17 Absolute. It makes a horrible noise when the grey button is pushed. The brushes rotate and I checked for clogs...can't stop the noise


... Dyson All Floors Plus HEPA Bagless Vacuum

The carpet brush on my DC25 Dyson Ball Animal has stopped working. Is there a reset button ?


Next to the power switch is another button, this switches the brushbar on and off. The brushbar can be turned off for hard floor surfaces so as not to scratch them ... Dyson Ball DC24 Bagless Upright Vacuum

The motor in the power head ran at a higher pitch for a for 8 to 10 seconds then stopped. If I push the reset button the powerhead may or may not start or it may start and run for a few seconds. The brush is not caught.


Did you check the belt? A broken belt results in lower strain on the motor, causing it to run faster resulting in the faster speed and higher pitch. This could result in overheating, which will cause the motor to shut off.\015\012If this isn' ... Electrolux C101 Bagged Canister Vacuum

The brush on my bissell prolite multicyclonic vacuum won't turn. It seems like it is jammed, but I checked for anything that might be stuck in it and don't see anything. Is there a reset button?


I had the same problem with my old Bissell sweeper ( I bought a new rotating brush each time this happened then I bought a new sweeper the next time it happened -last Dec. 2009.) Unfortumately I bought a new Bissell and now it is happening again to ... Bissell 17G5 PROlite MultiCyclonic Bagless Upright Vacuum Cleaner

Faithful Sebo X1 upright, about 12 years old, stopped working today. I replaced old with new dust bag, checked all dust paths were clear, checked main brush was clear/clean, and drive spindle rotated OK with fingers. When power switched on, the two red indicators briefly flash on then off, but nothing more happens, motor does not start - even with power reaching machine. Tried removing all consumables, refitting and turning on a few times to reset, no joy. Removed base cover, both belts were i


At 12 years, this vacuum has had a good long life. I suspect the motor is shot, but it could be due to faulty wiring and connections. A bad switch, break in the power cord, and worn brushes in the motor are other causes.\015\012I recommend ta ... Sebo Automatic X1 Bagged Upright Vacuum

The brush doesn't rotate. I cleaned dog hair from it that might have been the source of the problem. I don't see a reset button so not sure how to get it turning again.


You might need to change the belts. These are the ones you need:DC14 Replacement Belts ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

The rotating brush stopped working after it grabbed a matress skirt. The skirt did not roll up into the vacuum. Is there a rest button?


Did it smell like burning rubber? If it did the belt is probably stuck and needs to be replaced. You can look at the little black belt on the bottom of the vacuum and see for yourself.You may have a extra belt that came with the vacuum. I fnot you ca ... Dirt Devil Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0625 seconds