Having problems with your Hoover SteamVac F5914-900 SpinScrub Upright Vacuum ?

Model number f 5912-900 hoover steam vav with clean surge.This is not the f5914 model........my new machine has 10 min. on it...in mid use it has stopped sucking and now is blowing more than anything, I took the front clear piece off as well as the black cowling/shroud and can find no obvious hoses to un-clog nor anything else to un-clog for that matter...I am looking for advise to fix this thing now, myself


Answers :

Here is a list to go by for no suction problems that you can follow along with they are common proble\015\012Problem #1 Steamvac is not Sucking!

If your Hoover Steamvac was working properly and suddenly it is not sucking any water, nine times out of ten, the culprit is the lid on the lower recovery tank. The lid on the lower tank (or dirty water tank) needs to hinge at the front and snap down at the back in order to creat a proper seal. If the lid snaps on but is not locked on at the front, you will not get any suction. Simply take the lid off, and ensure that when you put it back on, it must hinge on the front tabs of the tank.

Problem #2 – My Steamvac is still not Sucking!

Right now you are thinking that you shouldn’t have let your brother borrow your Steamvac. And you are right, because he used the hose attachment and returned it with the hose still attached to the front of the tank (some models only). Now when you try to use it there isn’t any suction. In this case, you are missing your tank duct. On models where the stair/upholstery hose attaches to the front of the recovery tank, one must remove a square plastic piece in order to attach the hose. This square plastic tank duct must be replaced before the Steamvac will operate properly in the upright position. So call you brother on the phone tell him to find it, or call me at the number at the top of the screen to order one.

Problem # 3 – My Steamvac isn’t sucking very well and the brushes are spinning slowly

Most the likely, the culprit here is under the recovery tank. Standing behind the steamvac with the lower tank off, to the right and front you will notice a round duct opening about 2 inches in diameter. This should have a rubber seal on it. If it is missing, look under the hood of the steamvac it may have fallen forward there. Otherwise, give me a call to get another one.

Problem #4 – My Steamvac brushes are not spinning or are spinning very slowly

Believe it or not they may just need to be cleaned! You can remove the rack of brushes by pinching the tabs on either side and pulling it out. The plastic is clear so you can see if the brushes and gears are gummed up with hair and carpet fibres. Rinsing usually works best. There are two more things to check if this doesn’t solve the problem. First, check that the switch for the brushes is set to high. Second, look under the clear plastic piece near the switch (it is removable). There is a small screen that collects lint and hair (like a dryer screen!). This is the air intake for the turbine that drives the brushes. Clean it off and your back in business.

Problems #5, #6, #7 – My Hoover Steamvac doesn’t turn on, leaks, or is really noisy

Unfortunately, these problems are usually a bit more complicated and need professional service. At Clean Machines we offer a free estimate/repair ceiling service which gives you assurance that repair bills don’t get out of hand. Please visit us at our store at 111 West 2nd Ave in Vancouver for all your Hoover Steamvac carpet shampoo, stain removers, and free tips on cleaning.ms and easy to remedy:
Repair Help & Product Troubleshooting for Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Model number f 5912-900 hoover steam vav with clean surge.This is not the f5914 model........my new machine has 10 min. on it...in mid use it has stopped sucking and now is blowing more than anything, I took the front clear piece off as well as the black cowling/shroud and can find no obvious hoses to un-clog nor anything else to un-clog for that matter...I am looking for advise to fix this thing now, myself


Here is a list to go by for no suction problems that you can follow along with they are common proble\015\012Problem #1 Steamvac is not Sucking!If your Hoover Steamvac was working properly and suddenly it is not sucking any ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Vaccuum issue I just bought a Eureka upright model 5892 BVZ, my concern is, I bought it on sale (floor model) and it didn't have a manual with it. I took it home and tried it, and although it appears to be working very well there is not dirt in the catch bin on the front of the unit. I tried the hose w/attachment and again it worked very well in picking up the cat hair, but where does the hair and the dirt go, I am afraid it is spitting it back out somewhere since I can not see anything in the c


If the dirt being vacuumed is not going into the dirt cup, then it must be just stuck in the hose and evenually will clog up. Check the hose and see it there is a clog in it, otherwise you have a years warranty on a new vacuum, take it into a warran ... Eureka 5892AVZ Bagless Upright Cyclonic Vacuum

I took the roller off my cleaner model 8910 and the black pieces came off as well and now I cant get them back on properly


Place the black brush arm onto the brush (the arm has a stand up pin / spigot which needs to be located into the centre of the brush) and slide black brush arm into base of unit. The black brush arm and brush should slide easily into original p ... Bissell 8910 ProHeat Clear View Upright Vacuum

When I took the base cover off the vacuum to clean the roller, a metal piece that is bent in half, as well as a white plastic stick piece came flying out. I think it might have to do with holding the vacuum in an upright position, but I don't know where it goes. Help!


They go in the slot beside the right wheel. Metal spring first, (the open ends facing away from front of vacuum base. The white nylon piece lays parallel and directly on top of the metal spring, round edge up, and aligned with the open ends of the me ... Eureka 411A Upright Vacuum

I have a dyson dc21. All the sudden the hose is hardly suctioning up anything. If I take the canaster off, the top air hole suctions extrememly well, but when I place that canister back on, the suction is not going thru the hose and picking anything up. I have squeezed the hose, I feel no air leaking and do not feel any blockages...what could be wrong. It worked fine the other day and today, it won't pick up a piece of lint!


... Dyson DC21 All Floors Stowaway HEPA Bagless Canister Vacuum - Iron/Titanium/Yellow

Can't find info for hoover steam vac spin scrub model # F5905900 on Hoover website, doesn't show that model number at all...looking for mesh (kind of cone/cylinder shape) that goes in dirty water tank (I think) and also the tool (wand) that slides into front to clean it out. It doesn't pull all the water up very well and the filter has been missing for some time. I don't know if that has anything to do with it or not. As far as the wand tool goes, I have taken the cover off at this point and


The cleanout tool is part # 43514001. The filter is # 90001398. Be sure to leave a 1/2 inch gap between the top of the filter and the bottom of the lid. If you need a manual, try model F5914-900 0r F5912-900 on Hoover.com ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

No spray My Bissell Pro Heat 7901 will not put out any spray. I Took the pump out so I could get at it and disconnected the hoses. I put the one on the input side and the other in a bottle of water. Put the belt on the pump and turned on the machine .Nothing at all coming out of the pump. Where can I get a new pump? Also the lever that goes to the little flapper at the top under the clear plastic piece on the front that connects to the knob that changes from tools to floor broke off. Where can I


Search for bissell pro heat pump. bissell.com will not have it ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

Our Dyson sucked something up last week (not sure WHAT) and now the telescoping hose won't ****. Well, it sucks but just BARELY . I took the hose apart and can't see anything, but it makes a weird noise now when you stand the unit up and are not actually vacuuming with it. Help!


Well if the hose is completly clear the blockage is either before that or after that the brush roller should come out to clean the tube as you know also comes out make sure all are clear right up to the collector ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

I have a vax v-2000u do they all blow a lot of air out off the front of them it blows everything all over and dosent pick up well i have too get tools out to pick anything up


Yes, andrea.....if only it could **** as hard as it can blow!! mine blows so hard that it blows all my fridge magnets off my fridge!! ... Vacuums

I have a Panasonic MCE6003 vacuum cleaner. I regretfully leant it to a neighbour and it came back full of dog hair and keeps cutting out. I cleaned out the dust container and the main filter but it still kept cutting out after 5 minutes. I decided to unscrew the part with the motor and wash the filter inside.It was all going well until a large rubber washer bit, a piece that looks like the thermostat and a little white button attached to two black wires fell out and now I have no idea how to put


... Panasonic Vacuums

Motor Fried? Eureka 431BX Vacuuming, and then all of the sudden the motor just stopped. Well idk if it's called the motor; the beater bar still spun, it was just the fan that stopped spinning Here is the whole vacuum in pieces http://i28.photobucket.com/albums/c237/SirFafner/Vacuum001.jpg Bottom Part, beater bar already taken out [Functions Fine] http://i28.photobucket.com/albums/c237/SirFafner/Vacuum002.jpg White Wire connecting to the fan motor [Looks black, i think it's fried, and that's the


Funny you said that,I went today and bought a bissel at Wal-Mart.Sure hope it lasts longer then the Eureka did.I will probably try to take the other one back to the store if I can find the receipt.Thanks so much. ... Eureka 431BX Bagless Upright Vacuum

No spray My Bissell Pro Heat 7901 will not put out any spray. I Took the pump out so I could get at it and disconnected the hoses. I put the one on the input side and the other in a bottle of water. Put the belt on the pump and turned on the machine .Nothing at all coming out of the pump. Where can I get a new pump? Also the lever that goes to the little flapper at the top under the clear plastic piece on the front that connects to the knob that changes from tools to floor broke off. Where can I


Pump part number is 2107181, the diverter valve # 2136988. You can Bissell and they can tell you who may have parts near you, or you maybe able to order thru Bissell.com. Before you took it apart, were you getting water to spray out of the hose. I ... Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum

It's been awhile since I have used my shampoo system on my Ultimate G series Kirby. Well, as instructed I took it apart and cleaned it. Now I can?t figure out where to put the ?screen cap? and ?sponge filter?. I have my manual in front of me and the only place it shows the filter and sponge (page 35 in the manual) is when it?s been taken apart to clean. It doesn?t show where to put it back. I don?t know what I would do without all the pictures in the Kirby manual. HELP! Thanx. Visual Kirby Vacuu


Hello,\015\012The littlew round screen goes in the hole where the hose attaches to the tank. The round foam filter goes up in the hole underneath the on/off valve for the foam. Here is a guide if you need any more help...\015\012\01 ... Kirby G6 Bagged Upright Vacuum

My Kirby G6 light is not turning on when I start the machine. I took off the front piece and removed a lot of hair from the roller and interior. Since I did that, the belt keeps coming off (even though it is fairly new). Is that the reason the light won't turn on? Is there any advice you can give me before I take it in?


The light indicates that the brushroll is spinning. If it isn't coming on, the power nozzle may have been reinstalled incorrectly. Take the nozzle off and then use my step-by-step guide to reinstall it. I expect that it will take care of the problem. ... Kirby Vacuums

We have several SGC-60D 1.5 Gal coffee urns and the front piece broke off. ( the tall rectangular piece that hold the tube on the front on) We've tried a couple of things but the new front piece won't connect to the screw to hold the tube on. Any suggestions?


... Vacuums

I have a yellowMiele Vacuum,model=Electronic Air Clean Plus S3121. On the main body the part that the pipe/nozzle clicks into has a piece that has snapped off. I can see this by lifting the lid and the black plastic piece that is screwed to the inside of the lid has a piece chipped of it which means that when the nozzle is clicked into place it is completely loose. There is a black piece that clicks into the inside of the hoover into this broken part which is still ok so at the moment by linin


Generic problem for all Vacuums\015\012I have a yellowMiele Vacuum,model=Electronic\015\012posted by maura497 on Apr 18, 2008\015\012Report abuse\015\012 ... Vacuums

Not picking up anything as well as it used to.


Try putting new filters in, and check the hose for blockages, Iain ... Eureka Capture Upright Vacuum Vacuum

My Bissell ProHeat 2x is pouring water out of the bottom anytime it's turned on. I had it in the shop for no water, took it back again for the same problem, took it back again because it had no suction, finally took it apart and found the problem with the suction and fixed it myself. Worked fine for a day and now it is constantly leaking water, if it's turned on, and is useless for anything except for making a mess.


Took the unit apart and discovered my heater had small pinholes in the metal and they had put in silicone, instead of a gasket, which didn't seal. So much for the place I took it to "saving" my heater for me. I repaired it myself by getting a few o ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Sears progression kenmore canister va. Model 11623612300 on the wand, the plastic piece broke off, there is one long wand with two piece to it well the plastic piece, not on the bottom, where it hooks into the beater bar thing, but the other plastic in the middle. Can this be replaces?


Hi.The part is probably available as replacement.Please click here ... Kenmore Vacuums

Broken piece The black plastic octagonal end of the brushroll has broken off the brushroll, so the brushroll won't stay in place. Can I get another little piece to attach onto the brushroll? Or do I have to get an entire new brushroll? And if so, do they sell replacement brushrolls? CP


You will have to replace the brush roll, part #60844-5, belt # 61120B. You should be able to get them from a repair shop, get the right one or it won't work right. You maybe able to go eureka.com and order direct. ... Eureka 4700A Maxima Bagless Upright Vacuum

I took apart my beam rugmaster plus model 045-322 and cleaned out "stuff". Now I can't figure out how to put one piece back in. Is there a diagram somewhere that I can look at? It consists of 2 pieces of metal that go to the right of the handle tube.


... Beam Industries Vacuums

I would like to know how i get the very bottom piece off my vacuum off so I can put a new fidder hose on it? The hose is black and it is only about six inches long. its lacation is on the very end of the vacuum but between the end and the piece that gos along on the floor.


You don't have to take the vacuum apart.\015\012Assuming this is an Epic 3500 or similar upright Electrolux:\015\0121. Lay vacuum on it's side.\015\0122. Gently pull hose from power head. It's not screwed in so that should be eas ... Electrolux Epic 3500 Vacuum

My Sharp EC-l2TWT4 throws belts and I noticed the motor shaft was not running straight. My wife took it to my local dealer in Brainerd,Mn and they said it was fine.So I took it apart and found the plastic motor housing had melted at some point letting the motor twist out of alignment. Other than this, everything works great.Can I order this plastic housing piece somewhere?


I checked the schematics for that model and the motor housing for that model is no longer available. Your best bet is to either attempt to find a used part or trade it in and get a new unit. Sharp no longer makes any vacuums or parts which makes thes ... Sharp Twin Energy EC-12TWT4 Bagged Upright Vacuum

I need the recovery tank front panel for the Hoover Carpet Cleaner, i have the tank can i just order the little piece that goes in the front of that for the suction to the recovery tank


Unfortunately its only available as one unit the hood, and suction cover ... Vacuums

How do i remove the front of the Proheat Clearview to clean it out? I removed the two obvious screws at the front sides of the clear plastic part but see anything to remove to take it off.


... Bissell 1699N ProHeat Clear View Force Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0517 seconds