Having problems with your Hoover SteamVac F5914-900 SpinScrub Upright Vacuum ?

When I put the water tank on the unit it just starts draining out the bottom. It worked fine last time, so I don't know if some gasket or something is now missing?


Answers :

Check the rubber "O" ring on the water tank and also the outlet valve they get stuck up? the "O" rings get hard and brittle
Repair Help & Product Troubleshooting for Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

When I put the water tank on the unit it just starts draining out the bottom. It worked fine last time, so I don't know if some gasket or something is now missing?


Check the rubber "O" ring on the water tank and also the outlet valve they get stuck up? the "O" rings get hard and brittle ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Hi. I have a Kirby from back in the early 90s (model G3D). Never had major issues with it. Can't remember the last time I had maintenance/tune up done. It's just sounding different when I run it the last few times...almost like it's louder and kind of echo-ey. Still suctioning well, but something's not right and I don't want to run it until I know if anything's up. Any suggestions? I'd like to try and figure this one out on my own with your help. Thanks in advance for your help. Marci


Check the belt. this is a strong vaccume and even without the belt it will still have a decent amount of suction. If the belt is not tight or intact it can let the motor turn faster which will sound louder. other than that check all the hoses for hol ... Kirby Ultimate G Bagged Upright Vacuum

I bought the Eureka 4703D model vacuum and my very first time powering it on, it was extremely loud - abnormally loud, and I don't know if it is loud like that because I possibly put it together wrong, or there is something wrong with it or it was previously damaged and I would like to know if this is something I can fix myself or do I have to take it back apart and return it to Walmart where I purchased it from. When it makes the loud noise, it does vacuum fine but the noise is just unbearable


... Eureka Power Plus 4703D Bagless Upright Vacuum

The last time I sewed with my Necchi the tension was fine. Today when I threaded my needle, the thread felt tight in the upper tension dial. I tried re-threading the machine several times, but it didn't help. Now the parts of the tension dial are all loose and wobbbly and I have no upper tension. Doesn't matter what the dial is set on. The tension dial appears to be broken, but I don't know how that could have happend since I store it in a case.


I found this thread (no pun intended):\015\012\015\012http://www.fixya.com/support/t2902978-need_replace_upper_tension_dial\015\012 ... Vacuums

I have a Hoover SteamVac F5914-900 SpinScrub... The last time I used the hand tool attachment, it worked fine. Just tried to use it again, and now I only drips of water will come out of the hand sprayer, if that. I have tried prepping it for up to 15 seconds like the manual says... no luck with that. Also it is making a big puddle on the floor, probably because the brushes on the main unit keep spinning when I am trying to use the hand tool which I dont think they are supposed to do? Can a


The brushes can be turned off on most of them via a switch on the hood. There shouldn't be water coming out onto the floor unless you are pulling the trigger at that top. You probably broke this when attempting to use the tools. ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Our Bissell Cleanview II 3576M does a great job except that the filter cup below the dirt cup gets full very fast and the dirt cup barely has anything in it. To clean the whole house, I have to empty the dirt cup and clean the filter several times. It didn't use to work this way. It seems like something is missing, a gasket or seal maybe? I don't think dirt, hair and debris should be going straight to the lower cup and bypassing the upper. I looked at the user guide but can't see why it's happen


Contact Bissell Direct for a parts diagram and support at \015\012\015\012http://uk.bissell.com/EmailUs.aspx\015\012 ... Bissell 3576 CleanView II Bagless Upright Vacuum

We are having suction problems. ran over a chord and there is now no suction when we turn it on. last time we brought it in, they said something about a gasket??


Hi,\015\012 There could be various reasons why this could happen.I will tell \015\012you the reason's that could cause this problem and its solution.1)\015\012 Internal hose has twisted small cor ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

We have bissell pro heat and I have put new belts on and took off the top plastic cover I blew out the lines and I still can't get it to pump water or solution. The red little spinner flow indicater does'nt get water, if I pour water into it it runs out the front. I guess I don't know what else to do. The machine worked fine the last time we used it about 6 months ago. Any suggesttions?


Did you check and make sure the belt is still on right? They do come off from time to time.There are like 6 long screws holding the top cover to the bottom. The are real pain in the behind to put back together once you take them off. T ... Bissell Vacuums

I take apart and clean my DC17 every 2 weeks. When I put it back together it always works perfect. This last time, I noticed that the self propel is not working...am I missing something? I took it apart to be sure eveything is in it's place but no difference. Now I have to push really hard.Any suggestions?


The roller is not spinning do to motor or belt not working. If it is the motor then the machine will have to go back to dyson if it is the belt then that is an easy replacement. ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Shop Vac was working fine last time I used it. Now I try to turn it on and nothing. I have cleaned the terminals on the toggle switch. I know there is power to the switch


Try tapping the motor area with a piece of wood or something, damp usage may have seized it up a bit ... Shop Vac 925-09-62 QSP Plus Wet/Dry Vacuum

My oregon scientific projector clock keeps changing time, I think it might be something to do with the time zone. I do not know what a time zone is?


A time zone is section of the country that adjusts for daylight savings time. The United States is composed of four time zones - Eastern,\015\012 Central, Mountain, and Pacific. Each county is assigned to one of the \015\012four time zones. See th ... Vacuums

Nothing happens when i turn on my vax 6131. The machine worked fine last time used and the fuse is fine.


... Vacuums

Vacuum either stops for no reason and can't be restarted without unplugging and waiting 1/2 hour to restart, or it simply will not turn on at all. The red light comes on when the "On" button is pressed. I took it back today for the 4th time in a month to where it was purchased. They called later and said it was running fine and they could not detect a problem. The last three times they have (1) replaced the roller brush, (2) "unclogged" the vacuum, and (3) "adjusted" the belt.


This sounds like it might be an overheating problem. \015\012\015\012Some vacuum motors are fitted with thermal cut out fuses or thermistors which cut off the flow of electricity to the motor when the temperature gets to high. It is possi ... Lindhaus Activa 30-38 Bagged Upright Vacuum

I have a bissell proheat carpet cleaner purchased in 4-18-2005 for $169.99 from kohls I have used it 6 times and the last time the brushes would not move cause the belt was broken and the end of the pump pulley which is plastic broke off so I reorder the pump unit and 2 new belts and now I see you have sent me a exact pump but the end that broke off that the belt rides on is made of steel or aluminum much strong piece of equipment I want to know if there was a recall for the machine due to mecha


I've owned my Bissell for over 5 years now & LOVE it! Even after vacuuming It pulls up tons of dog hair I never realized was there! I am having a similar problem, but I caused it myself & think maybe you may have the same problem, cross you ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

My Dyson vacuum works fine for cleaning the rug but the hose doesnt get any suction at all. I removed the hose and all the parts around it that I could and dont see any clogs or broken pieces. I lost my manual so I dont know if this is addressed, or if there is a switch Im not flipping. Gave it a thorough look but found nothing.


Hi there,Sorry to hear you're having a problem with your DC07. If you have suction through the cleaner head but not through the wand, it sounds as though you have a blockage. Although you say you've already checked for these, you may find ... Dyson DC07 Bagless Upright Cyclonic Vacuum

The brushes are not spinning at all. I have checked them and they are snapped in securely. It was working fine last time I used the machine. I have cleaned them and they spin manually just fine.


You probably got a piece of foreign material jambed in there for a moment and it "smoked the belt" that spins the brushes,it will either have the belt on either side of the brush housing cylinder or like kirby vacs the belts around the cylinder and i ... Hoover Floormate H3000 Upright Wet/Dry Vacuum

Good evening, I have a Xio Z1010 electrolux vaacum cleaner and I hope you'll be able to give me some advice. The vacuum cannot be started. Last time it started for a few seconds and stopped suddenly. Something similar happened long time ago but that was due to overheating. Once cooled down in few hours it would start again. It is not the case now after 24 hours. Could you give me any idea what could be the reason? Your help would be much appreciated. Adorian


... Electrolux Vacuums

My spin scrub was working fine last time...this time I pulled it out (we have had it about 6 months) and it is only blowing air, not sucking back in. Is there a setting that is incorrect?


Assure the ring gasket is in place under the hood. A round rubber gasket must be in place on the round tube under the hood where the recovery tank sits to connect the vacuum from the motor to the round tube on the bottom of the tank. ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Bought a new sweeper and brush ( beater bar ) does not turn. The large belt is fine and turns. The small thin belt is also fine but does not turn the brush. It is either the wrong belt or is there something that could be missing to put tension on it ?? Thank You [email protected]


Jim, To put tension on the brush, tilt machine forward when upright, move carpet selector knob to carpet. then turn vac on. Brush will only spin when vac is tilted back to operate. brush stops when upright and on to use hand tools so the er is no dan ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

My electrolux oxygen vacuum cleaner shut off and will not turn back on. It's less than a year old, but I bought it off Craig's list--they were the orginal owner and they said they bought it in May of 2008. I've only used it a few times and it worked fine except for the last time when it suddenly just shut off. I thought maybe it had come unplugged and I didn't really worry about it because I was finished vacuuming. But, I went to use it tonight and it would not turn on at all--no lights, nothing


No..Electrolux is really great about warranty service. They will help you even though you are not the original owner. ... Electrolux EL7020A Oxygen 3 Ultra Canister Vacuum Cleaner Bagged Vacuum

My bissell proheat will not shoot water out of the carpet cleaner or tool cleaner. Checked belt and it is fine. I worked just fine last time i used it, which was about 1.5 weeks ago.


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

Our Winsdor Sensor XP12 does not show any power or lights, I did check the handle connection, it was fine. The power cord has been repaired with duct tape 3-4 x where someone has sucked up the cord, this may be the cause yet it ran fine last time it was used! so I am at a loss, please help if possible.08/31/2010 Steve


Any time the cord has been damaged badly enough to require taping, the possibility or intermittent "opens" exist. This means the wires are in contact much of the time, but will losed contact periodically. Even if it worked fine seconds ago, jigglin ... Windsor SR12 Sensor Bagged Upright Vacuum

My oreck xl 3800 H2 upright vacuum cleaner does not turn on. It worked fine the last time I used it. Is there some sort of fuse that may have burned out?


Usually no fuse on these.\015\012\015\012Assume the outlet has been checked?\015\012\015\012I'd look at the on/off switch (that is a 2 speed unit, tight?) or the diode the gives the 2-speed choice, or the power cord as my firs ... Oreck Vacuums

A family member recently gave me their Kenmore Vacuum Cleaner (model 35821) and I did not notice that the power cord was missing at first. I tried to look closely at the manual online to see if this was something I would be able to purchase or if the vacuum was no longer any good. Do you happen to know if there is a replacement part for the actual power cord for this item?


Any power cord 17 gauge or lower will work ... Vacuums

Worked fine the last time I used it. Went to turn it on this week, and nothing. I thought a fuse was out. Tried multiple outlets, that wasn't it.


The motor probobly blew out. ... Dirt Devil Vision Turbo W/Bonus Upright Vacuum Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0613 seconds