Having problems with your Hoover SteamVac F5914-900 SpinScrub Upright Vacuum ?

The panel came off of my SteamVac water tank, and I can't figure out how to get it back in! HELP!


Answers :

I think that you mean the little white/grey/sometimes clear panel that fits on the dirty water tank.
\015\012
\015\012Remove the lid of the dirty water tank, and slide it down the front of the machine to the clear housing below. It will only fit in one way as it is somewhat triangular shaped.
\015\012
\015\012if this is not the piece in question, the manual is here for you :
\015\012http://www.hoover.com/pdfs/manuals/F5914900.pdf
\015\012
\015\012Good luck.
\015\012Mark
Repair Help & Product Troubleshooting for Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

The panel came off of my SteamVac water tank, and I can't figure out how to get it back in! HELP!


I think that you mean the little white/grey/sometimes clear panel that fits on the dirty water tank. \015\012\015\012Remove the lid of the dirty water tank, and slide it down the front of the machine to the clear housing below. It will on ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

I have a dyson DC14. the forward lock came out and I cant figure out how to get it back in. Please help!


... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

I have a Harmony vacuum that's a couple years old. I recently sucked a fair amount of dog hair into it and was unaware something was amiss since the things so quiet. It just shut down and wouldn't come back on. 10 minutes or so later it came back on but now it's got no sucking power. I figure I torched the motor. Good guess? What are my options--I'm out in the middle of no where but can get it to a repair shop 250 miles away. Is it worth trying to salvage or am I going to pay as much to get it f


I cleaned the whole thing out, changed out all the filters again and cleaned out the motor compartment. Then I discovered a huge clog in the line. Once I got that all done--it's now working like a charm. Moral of the story: spend more time looking fo ... Electrolux Vacuums

Hover F7452-900 My brushes are not turning. I have taken the tanks off to check the switch that changes from carpet to hard terrain to Ceramic tile.I noticed that there is a spring that has came off. I tried to disassemble the top half (nose) of the cleaner but I have came to a stand still. I cannot figure out how to remove the cover so I can figure out where the spring should be attached. I have removed all the screws that are visible and it still won't budge. It is loose but on the back side o


Regarding the brushes not turning:\015\012\015\012Your filter may need to be cleaned. It is located behind your brushes. With your tanks removed and the cleaner unplugged; tilt your cleaner back. The filter screen located behind your b ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

I have a windsor vsp 14, it is making a bad grinding noise, when I take the top blue piece off it stops, the brush works fine and when I put the top back on it grinds really loud and gets hot. it still vacuums and the belt and brush are working fine, can't figure it out. and when the lid is on I cant see what its grinding on. It only makes a grinding noise when you pull handle back and engade to vacuum flor and stops when you put it upright.


... Windsor VS14 Versamatic Bagged Upright Vacuum

I have an older model F6056-900 Hoover steamvac Spin Scrub Cleaner. My first problem was that I loaned it out to a friend. Anyway she ran over the hose (used for attachments) with her car. I tried using the cleaner for carpet cleaning this morning but when I tried to put the solution tank into place...its loose...won't snap back in like it used to. When I can get it somewhat in place the solution just complete drains out through the bottom fo the tank. The leak is where the small hole on the bot


... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Vapor Clean TR 5 Under "maintenance" they told me to unscrew to empty refill tank. After doing that, no water came out and the piece that the scew went into is now in the tank. It is too large to get out and even if you put the screw back inti that piece ir still goes into the machine. Can I still use the machine? brand new only uded it once


I is really needed to check this with the manufacturer! See contact details below: ... Vacuums

Is there a diagram/picture to help me visualize how to put cleaner belt back in vacuum? I was taking base of vacuum apart so I could get rid of hair that were wrapped on the roller. The cleaner belt came to loose and I could not figure how to fix it back. the model is eureka upright bagless series 430


Hi,Sorry to hear your belt fell out. Not good if you've never replaced a belt before...Here is a website where you can read a detailed description of how to change a belt: http://www.ehow.com/how_8034505_eureka-belt-replacemen ... Eureka 431A Optima Bagless Upright Vacuum

HOW DO YOU CHANGE THE BELT ON A HOOVER WINDTUNNEL T SERIES REWIND VACUUM..THE BELT BROKE BUT WE CANT FIGURE OUT HOW TO GET IT BACK ON RIGHT.


... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

Lost Suction This is my second hoover steamvac and i am having the same problem with my new one as i did with the old one that i tossed out. I have used it about 12 times and it worked great the first 6 times... Now i'll empty a full tank of water and only half will get sucked back up. I have tried taking it apart and cleaning and also the rubber seal had some gaps so i sealed those thinking that it was leaking air from there...can anyone help? I am so close to chucking this one and buying somet


Usually when there is no suction, one cause is the lid to the recovery tank is not on all of the way in the back. Also if you have that foam filter on the underneath side of the recovery tank lid, it needs to have a 1/4 in or so gap from the top of ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

Having trouble i have a hoover steamvac f5815...i cannot figure out how to **** the water back up into the reserve tank... any advice?


Still no HELP> does it help that i am cute and quite stacked? I am so kidding ... Hoover F7431-900 SteamVac Vacuum

Kirby belt my belt on my kirby ultimate g came off and I can't figure out how to get it back on please help!


Check out my online guide. I also have instruction manuals!\015\012\015\012http://reviews.e ... Kirby Ultimate G Bagged Upright Vacuum

I took the roller off my cleaner model 8910 and the black pieces came off as well and now I cant get them back on properly


Place the black brush arm onto the brush (the arm has a stand up pin / spigot which needs to be located into the centre of the brush) and slide black brush arm into base of unit. The black brush arm and brush should slide easily into original p ... Bissell 8910 ProHeat Clear View Upright Vacuum

Cant figure out how to get the water to suck up into the reserve tank


... Hoover F5832-910 SteamVac Supreme Vacuum

There seems to be a wheel that holds tension to the belt which came off. Now the belt spins and makes a grinding noise. I cant figure out how to get to the belt? Any one have advice?


I can help you a lot further if you can send me a picture of the bottom side of the vacuum. My email is [email protected] Once I see a picture this will help me tell you how to fix it. ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

The back wheel came off and i went to put it back on and the other wheel that connects to the mechinism/gear height ajustment that goes up/down with a spring in it came off as well. i have been looking for a schematic to put it back together but cant find any.


You do not need schematics, it is fairly easy. Clean and lubricate the teeth on the inside of the front wheel shaft assembly. Insert the spring into small pedal and place the pedal designated opening on the Kirby front fan casing with teeth facing ou ... Kirby G6 Bagged Upright Vacuum

The tension knob came off of the front of my sewing machine while I was sewing. I cannot figure out how to put it back on. I have the metal rod that fits into the back of the tension knob, but cannot figure out how to put it back into place. Keeps falling off


It sounds like your machine is the kind that has a knob with a 'set screw', a teeny tiny screw that tightens and holds the thing in place on the rod. Look for a small hole, probably on the bottom and look for a very small screw near the machine. ... Vacuums

Cant get the power bush back on


... Bissell 8910 ProHeat Clear View Upright Vacuum

How do i take the old belt off of my dyson dc 14? cant seem to figure out how to get the roller separated from the machine because i cant get the old belt off.


Go to: Dyson web site or \015\012\015\012 http://www.repairclinic.com/0100_24.asp\015\012\015\012There should be 4 to six screws holding the ... Vacuums

Bissell Proheat - I need the manual - how do I get the water container back into the machine? I took out the tank and filled it up with water but I cannot get it back in. I need a manual or a picture of how to do it. thank you, ruth


Http://www.bissell.com/images/UserGuides/7950_1204.indd.pdf ... Vacuums

I HAVE LOST MY INSTRUCTION BOOK FOR THE STEAM VAC SPIN AND SCRUB. I WANT TO USE THE STAIR ATTACHMENT, BUT I CAN'T FIGURE OUT HOW TO HOOK IT UP, OR OPERATE IT. I SEE WHERE THE PLUG IN PART GOES IN THE FRONT OF THE MACHINE, BUT I CAN'T GET THE OTHER PART TO SLIDE INTO PLACE ON THE FRONT OF THE RESOVIOR TANK AFTER I REMOVE THE FRONT PANEL, AS THE DIRECTIONS ON THE FRONT OF THE RECOVERY TANK SAY TO DO. THE FIT IS JUST TOO TIGHT. WHAT AM I DON'T WRONG- OR HOW COULD I GET A REPLACEMENT INSTRUCTION BOO


You can download a PDF version of the manual at the link below. I believe you can contact Hoover as well and they might mail you one.http://www.hoover.com/CustomerService/Manuals/Default.aspxGood Luck! ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

I had to take apart hand tool for steam vac and now I cant get it back together. Please help.


... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Cant get cover back on Bissel Pro Heat


... Bissell 8910 ProHeat Clear View Upright Vacuum

CANT GET MY POWERSTEAMER PRO DELUXE MODEL 8804 BACK TOGETHER


Http://newzealand.bissell.com/images/IncludeContent/Service_Center_Help/Upright_Deep_Cleaner_Repai ... Bissell 1697-7 Powersteamer Pro Deluxe Vacuum

Cant get the bottom plate back onto my dyson upright DCO7i


You need to press hard and turn till they lock inhttp://www.youtube.com/watch?v=fN8k--LbuCs ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0624 seconds