Having problems with your Hoover SteamVac F5914-900 SpinScrub Upright Vacuum ?

How do i remove the hood for cleaning out debris?


Answers :

There should be three screws on this unit to remove the clear plastic hood.
\012
\012first, remove the dirty water container, there will be one screw there to remove. It should be rather long.
\012
\012next turn the machine over, there will be 2 more screws under the corners of the front of the machine (you can see the threads through the plastic on the top) remove the two screws.
\012
\012Now comes the tricky part. Turn the machine back over so that its the right side up again, you will want to pull away from the machine and up, kind of like you are going to bend the plastic up. Once you have that done the entire cover will come off.
\012
\012Good luck,
\012Mark
Repair Help & Product Troubleshooting for Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I want to clean debris out of the hood on my hoover steam vac F9515-900. How/can one remove the hood of this machine?


... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

How do i remove the hood for cleaning out debris?


There should be three screws on this unit to remove the clear plastic hood. \012\012first, remove the dirty water container, there will be one screw there to remove. It should be rather long. \012\012next turn the machine over ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Have Hoover SteamVac Model F5835-900. Has gunk under the front clear hood where water/debris is lifted from carpet to the tank. Wife wants me to remove clear hood to clean; however the hood cannot come off without damage. Can I safely remove this hood?


There 2 screws on the bottom edge, one on each side, then there is a ***** on top at just beyond the lip of the window. Then it will come off of the machine. \015\012\015\012 ... Vacuums

Model UH60010, Series X12.0, Mfg code K09A. While attempting to use the hose and the extensions to clean shelves, my wife reported no suction. I removed the brush roller and the plastic piece just below where the hose opening is located and saw a "flapper" door that was closed and had some debris sort of jamming it. I removed the debris, but the door requires extreme pressure to open to permit the dirt, etc to moved up thru the opening , through the hose, etc. I thught maybe that somehow tg


Hello,Check to make sure\015\012the dirt canister is empty. If dirt canister is full, then you will \015\012experience\015\012reduced suction. Empty dirt receptacle.\015\012 Could\015\012 be a clogged hose - ... Vacuums

Is it possible to remove the hood on the Hoover steam vac model # f5835900. I am unable to remove the debris stuck within the hood. Thank you.


... Hoover F5835900 Upright Steam Vacuum

Removing the hood to clean the cleaner


Http://geeksquad.fixya.com/ThreadView.aspx?prdid=41018&thid=498921\015\012Removing the hood to clean the cleaner\015\012Posted by bfy1952 on Apr 08, 2008\015\012H ... Hoover F5881-900 Vacuum

Kenmore bagless 116.36932502 the interior filter port fills up very quickly-withih minutes of initial startup-- and has to be removed and cleaned constantly. Debris backs up into the interior of the main filter as well, the main canister never gets full. New problem with old machine!


... Kenmore Progressive Bagless Upright with Inteli-Clean SystemVacuum

How do i remove hood on my Hoover F6028-900 Carpet Cleaner? I need to clean underneath it.


... Hoover F6020-900 SteamVac Upright Vacuum

Hoover wide path 6000 How do I remove the hood for cleaning


... Hoover F5881-900 Vacuum

I am replacing drive belt on Eureka 4870 upright. Before installing I removed bottomplate and was cleaning out accumulated lint, hair and grit. Found a pair of identical (reciprocal) felt gaskets sucurely inserted above and below the roller brush, and one small loose piece of felt approximately 1/3 inch wide by 1 inch long that came out as I was pulling out debris. It has a slight crease across the middle as though I was not resting on an entire flat surface, but I find no other clues as to wher


If you go to this URL:\015\012\015\012http://www.VacPartsWarehouse.com/Eureka-4870-Ultra-Smart-Vac-s/1928.htm\015\012\015\012in the exploded view of the unit, identifying the parts and look at item 18, I believe it is where your felt part ... Vacuums

Vacuum works fine when using the attachments, but as soon as we try to use it in it's normal upright position it does not work. We have cleaned all filters and removed debris from roller, but nothing has helped.


Greetings,\015\012\015\012There could be a few things that would cause your Dyson to do this. I will give you detailed step by step instructions along with pictures on how you can diagnose this problem. \015\012\015\012Po ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Hi, There is a high pitched whirring sound coming from lower part of the vacuum. When I tilt it toward me (while standing in the normal vacuuming stance) the sound sometimes lessens for a minute or so. I have tried the following things: -cleaned the two sponge filters -emptied the dirt receptacle -removed the roller and cleaned it -cleaned the brushes -the belt is not ragged and does not seem floppy -checked all of the airways for clogs (including removing the wheel base) Can you help?


Your looking for some dirt stuck in some thing you didn't check yet. with the roller out and the belt out of the way run it to see if it still makes the noise. if it does then you looking at the impeller or the motor bearing themselfs those bearin ... Bissell 3750 Lift Off Bagless Upright Vacuum

I have a DC07 and the brush wasn't rotating and I had no suction at the brush but perfect suction through the hose. I noticed a large build up of dog hair around the brush so I took off the cover plate and removed all the hair, cleaned inside the floor/brush housing and cleaned out the hose. I also cleaned the filter and removed the other air access cover and made sure that they were clear. I put everything back and the brush still doesn't turn and there is still no suction through the bottom


Hi and welcome to FixYa. I am Kelly. \015\012\015\012Here is a link that can assist you in your quest for the missing suction: \015\012\015\012 ... Dyson DC07 Bagless Upright Cyclonic Vacuum

My brushes on my hoover streamvac will not rotate. I removed and cleaned assuring that the filter was also cleaned. The only different thing I have done is to insert the upholstery attachment and removed it after use (didn't work so well) suction seemed weak. I am also noticing that there is air being blown out of sides where the dirty water container is. (don't recall that in the past).


... Hoover F5900-900 Upright Steam Vacuum

On the DC07, the entire cyclone assembly must be removed to empty the dust, debris, etc. collected when vacuuming. On the top of the cyclone is a "trigger" that you lift with your finger to release the bottom catch, which allows a clear flap to open on the "clear bin," thus letting all the debris fall out. My problem is when you lift the finger trigger, it does not release the catch on the bottom. Since the catch won't release, I cannot remove the entire clear bin either from the cyclone.Any sug


Beofre you go to the extent of buying a replacement canister, you can remove the top and using a straightened coat hanger type thing open that bottom lid. Then maybe you can clean the rim and possibly add some silicone spry to loosen things up. Here' ... Dyson DC07 Bagless Upright Cyclonic Vacuum

My Roomba stops within a few minutes of starting it and when I press the button, it says "Remove and Clean Roomba's Brushes." I have removed the brushes and cleaned them thoroughly, but within a few minutes, it stops again and says the same thing.


Hi,Accumulation of hair, dust and dirt in the Gearbox that prevents normal operation of the brushes. As a result, a power output is required to keep the brushes turning. As turning the brushes requires too much power, it con ... iRobot Roomba 4210 Bagless Robotic Vacuum

Vacuum smells I have a 6 year old rainbow vacuum model E and it smells terrible everytime I use it. Probably because often times i don't remove the water basin after vacuuming and just let it sit. It's my own fault however now I don't know what to do to get rid of this terrible smell. I've water cleaned the hepa filter, not able to remove the separator screw to clean. Can you give me some suggestions?


In addition to vinegar, baking soda (sodium bicarbonate) is also an excellent remedy for many odour problems. Try generously sprinkling baking soda on a rug you wish to clean, and afterwards, vacuum up the spot. Rugs, and dirt ... Vacuums

Keep getting message 'please remove and clean Roomba's brushes'. Have removed and cleaned brushes and even fitted new one's but still getting message. Also brushes sometimes rotate, sometimes not and not picking up very well at all. Help!


Must be your inbox is full, Delete old / unwanted messages. It should resolve the problem ... iRobot Roomba 500 Series Virtual Wall Lighthouse 80201 Robotic Vacuum

The removable filter at the front is cleaned regularly, and is not clogged. However, the machine appears to be suffering from being clogged by dust, as it has started to make a high pitched noise, and I fear it may burn out. I can see some dust inside the front panel but cannot see how to remove the front to clean it out. (NB. I have located two screws - one on either side - but cannot see how to proceed further.) Please help! Thank you.


\015\012\015\012Hi,Here\015\012is a tip that I wrote about my Bissel but I bet you have the same\015\012problem and the hose is clogged...Bissell Bagless Upright\015\012 ... Vacuums

My son spilled mica all over my carpet. To clean it I used my bissel vaccuum. Now I have orange mica in the removable filter area as well as up inside the part that spins. I need to clean it out, but don't know how to remove it from the vaccuum


Load it into the trunk of your car, take it to a gas station and use the tire inflater hose to blow all the **** out of it.\015\012May have to get a tire stem in order to use it as a blower. ... Bissell 37604 Lift-Off Pet Bagless Upright / Canister Vacuum CleanerVacuum

I have a Bissell 3920 and the beater bar only turns when I'm pulling the vacuum.How do you get the end caps off of the beater bar to clean it out? This has happened before when it was under warranty and I was told to remove caps and clean frequently.I am afraid prying them off will break the vacuum.It also has very low suction and I have cleaned the filters and the belt is fine.Will cleaning the inside of the beater bar fix my problem?


... Bissell 3920 Cyclonic Pet Hair Eraser Vacuum

Roomba Discovery My Roomba turns on and moves but the brushes won't turn. Someone told me that I had forgotten to put in the yellow and black end bearings, but I did. Help, I miss my Roomba I have a Roomba 530, I have had it for 2 weeks and really loved it. I have followed all the cleaning instructions etc.. Then the Roomba wanted it's brushes cleaning "please clean Roombas brushes" So thinking that something was stuck I removed and cleaned the brushes, (yellow tabs on and in place by the way)


I read somewhere that you need to clear the software in case there is a glitch. To do this, take the battery out and then, simultaneously hold down the "spot" and "clean" buttons for 30 seconds. Replace battery. This has worked for my Discovery model ... Roomba Robotic Floor Bagless Vacuum

How do i remove the front of the Proheat Clearview to clean it out? I removed the two obvious screws at the front sides of the clear plastic part but see anything to remove to take it off.


... Bissell 1699N ProHeat Clear View Force Upright Vacuum

I have a eureka bravo upright model 9600. I have removed the hood . I need to remove the brushe roller to install a new belt. I cannot figure out how to remove the brush roller.


Check out this URL:\015\012\015\012http://www.svcvacuum.com/beltrep2.html\015\012\015\012looks like it has just what you are looking for.\015\012Would appreciate a thumbs up on this if you find it beneficial.\015\012Paul ... Eureka Vacuums

IRobot rumba 4000 seems to run ok and then starts making a kinda hi pitched growling noise and slows way down. it is very clean(blown clean with air compressor)sensors are clear ,newly installed well lubricated on ends of brush and beater bar, new battery. it seems like the wheel tracks may be dragging . i have cleaned and lubricated where i could on them but can't find a way to totally remove and inspect wheel tracks.


It sounds like your Roomba's brush gears are not working. Run the robot without the dust bin to see if the brushes are turning. If they are not, the robot will need to be replaced. Contact iRobot CS for support at (877) 855-8593. ... iRobot Roomba 4000 Bagless Robotic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0678 seconds