Having problems with your Hoover SteamVac F5914-900 SpinScrub Upright Vacuum ?

Just got spinscrub this afternoon and worked great until had to empty dirty water. Now there is no suction at all. Have tried to find clogs and nothing to be found. Am about to return the damn thing!!!


Answers :

Ok 3 things to check before re-boxing it up.

1) make sure that the lid is on properly. it should go on with the 2 tabs at the front of the machine, then click into place at the back of the machine.

2) when you emptied it, sometimes the dirt channel will fall out. This allows for the suction to go between the dirty tank and the clear channel for the water to be sucked back up.

3) when you remove the dirty water tank again, look down inside the machine for a circular hole. there should be a rubber gasket on it to seal up the tank for your suction. If it has come loose or is missing, retrace your steps between the machine where it was last used and the sink or wherever you dumped out the dirty water.

Good luck,
Mark
Repair Help & Product Troubleshooting for Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Just got spinscrub this afternoon and worked great until had to empty dirty water. Now there is no suction at all. Have tried to find clogs and nothing to be found. Am about to return the damn thing!!!


Ok 3 things to check before re-boxing it up. 1) make sure that the lid is on properly. it should go on with the 2 tabs at the front of the machine, then click into place at the back of the machine. 2) when you emptied it, some ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

No I did not my hose on the dirt devil does not have much suction on it I took everything apart and found nothing wrong no clogs anywhere but when I add an attachment to the hose it loses all suction...I looked for a switch to change from regular vacuuming to attachment found nothing why is this??????? Need a manual where can I find some information and a download on line manual??????


Try this. There should be a little filter unerneath the tank. just clean that filter or replace it. (9 times 10) thats the problem.\015\012\015\012good luck. ... Dirt Devil Vision Turbo W/Bonus Upright Vacuum Vacuum

Filters I have tried to find the filter that goes up inside the vacumm not the one on the front but when you take the disposal thing out the one that is up inside that, where do I find one? mine does not have one and everything clogs up in there.


There isn't a filter listed in the parts list for where you feel one should be. Your owner manual would tell you if there was. ... Eureka 2961AVZ Bagless Upright Vacuum

Dyson DC17 hose collapses when I try and use the pull out wand and attachments. Cannot see anything in the hose blocking the suction, filter is clean. . . help? Not sure how to find the clog and fix it. Thanks


Click the link below for full instructionshttp://www.youtube.com/watch?v=kWFn6dF1ah8 ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

My upright kenmore progressive vacuum will not suction up when using the sweeper. It will suction things when I use one of the tools. I have put in a new bag and have tried to see if anything is blocking the bottom. It sometimes makes a very loud noise when I try to vacuum. If I press the intell clean on and off yellow button the noise may go away but it still does not work.


Double check hose placement, making sure you have the hose inserted into the correct slot. The long attachment nozzle stores in the front hole on the right, and the sucking hose inserts into the rear hole on the right. I know this is too simple of a ... Vacuums

Poor suction The actual sweeper seems to work ok, but the hose attachment has some suction but not enough to pick up things I think it should and not enough to make the power brush spin. I've checked everywhere I can for clogs, but I can't see anything. And there doesn't seem to be any way to check to hose itself for clogs. I've cleaned out the container and the filters, but there's still a problem.


Check the inlet down by the brush roll, make sure it is open, if it is then the hose itself must have a clog. If the hose comes off, drop something like a marble in one end and see it it comes out the other end, if it doesn't then you have a clog. ... Dirt Devil M1100009 Reaction Soft Touch Cyclonic Upright Vacuum Cleaner Vacuum

Lost suction Been using hoover steamvac today, worked great for the fist 2 hours, got ready to start back at it, and it has lost suction, have tried and tried the water tank repositioning, and nothing seems to work.


There is a screen by the brush that may be clogged. Make sure the water tank is on tight ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

My Bissell Quicksteamer Model 1960-R won't spray cleaning solution. I have cleaned it and taken apart the whole thing. I can't find any problems. The holes are not cloged where the water comes out as I disconnected it and blew through it to be sure. The lines show water trying to go through. It is as if it doesn't have enough power to pump the water out when I squeeze the trigger. I am thinking it is the pump thing but can't find a replacement part for it.


... Bissell 1960-3 QuickSteamer Plus Upright Vacuum

I set up my ONYX SW2300XS which I recieved as a gift (so no reciept) for the first time today. At first it was working well, I inserted a dvd and it played well. I played with the zoom and the skip buttons on the remote a bit and left it playing while I went a did other things. I came back about halfway thru my movie and wanted to skip scenes but the remote did not work. So I tried the NEXT button on the machine. This did nothing, so I tried the STOP button and that did nothing, the dvd was


Mine does the same thing! The store told me it would play all formatted but it does not! Its junk!! ... Vacuums

Hoover Windtunnel My Hoover Windtunnel is 3 years old. It worked great until yesterday when it lost all suction. I have followed the manual to trouble shoot any possible clogs and could find none. Then I noticed that when I remove the dirt collection cup and held my hand over the vent the suction is fine and strong. So... I replaced the hepa filter thinking that might be the problem. That didnt' work. The motor runs fine. The suction without the dirt cup inserted is strong. As soon as you insert


Either the hose has a clog, or the inlet down by the belt is clogged. Is there suction at the end of the hose, if not then it is clogged. If there is suction, then it has to be clogged down below by the brush roll, check that inlet. There also is ... Vacuums

No suction my riccar 8850 has no suction. I cant find any clogs and there is some suction on the hose when using cleaning tools but when hooked up to the vaccum bag it wont clean


Replace your belt. Remove the baseplate, remove the brushroll, place a new belt around the motor pulley, then around the pulley on the brushroll, and pull the brushroll back into place in the nozzle. Spin it by hand to make sure it spins, (otherwise ... Riccar 8850 Vacuum

Suction I have no suction through the hose. I have taken this machine apart, and checked for clogs, have found nothing, but did give it a good cleaning, still I have no suction.


Hello tnwalkergal the hose may have a clog inside the hose at the bend you can take the hose loose and run a broomstick or a yardstick thorgh the hose this is how I find the clog ... Dirt Devil M086700 Vision Bagless Upright Vacuum

Hoover Windtunnel My Hoover Windtunnel is 3 years old. It worked great until yesterday when it lost all suction. I have followed the manual to trouble shoot any possible clogs and could find none. Then I noticed that when I remove the dirt collection cup and held my hand over the vent the suction is fine and strong. So... I replaced the hepa filter thinking that might be the problem. That didnt' work. The motor runs fine. The suction without the dirt cup inserted is strong. As soon as you insert


Mine does the same thing. There is no suction. I found that there is a door that opens when you tilt the handle in the down possition. I think there should be a spring in place so it can open. Until I find a replacement spring I have to open the door ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

Poor Suction My Dyson DC17 is having very weak suction. I have checked the areas that I can easily access and can't find a clog. What could be causing this?


The flexible hose between the beater bar housing and the connection to the dust bin might have come loose or has a hole in it. Check this hose for your low suction problem. ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Brush belt is broken,does this affect the suction of the vacuum.it barely has any suction,but i find nothing else wrong.


Yes, with this vacuum the belt being broken will cause a loss of suction. ... Dirt Devil M086700 Vision Bagless Upright Vacuum

My dyson ball has no suction ... i turn it on and sounds normal for a few seconds then it sounds like it clogs then no suction but i checked the tubes theres nothing there...


Take off the dust collector , put the machine somehwere out in the open air and switch it on if the motor runs up to speed then the probelm is inside the dust collector and it is probably a blocked hepa filter \015\012\015\012If the motor ... Dyson Ball HEPA Upright Bagless Vacuum - Iron/Satin Yellow

While vaccuming it just stopped. Tried another outlet and checked power cord. Did find tube clogged with a dirt clog but no motor strain heard. Cleaned it out, Still not running


On the back of most vac's , u will find a red butten,use that to reset the vac. but even if that works u can avoid this usely buy ajusying the vac to a higher set . that helps reduse strian that the belt gets.\015\012 thanks\015\012 ... Bissell 68001 Canister Vacuum

Blocked suction The FLOOR suction line (Hose) is clogged. I Can vaceum the floor, but it will not pick up anything because the hose to the bagless canister is blocked. I can switch from floor to hose and can vaceum furniture. it will not pick up off the floor. I have tried running a wire down/up the hose. I Can feel the blockage, but I cannot get it out. I am afraid to pull the flem hose out as I do not know how it is attached at each end.


Hi,Here is a tip that I wrote about my Bissel ... the hose should just pull out... it is just stuck in there tightly...\015\012Bissell Bagless Upright Vacuum ... Royal 088500 Featherlite Upright Vacuum

** suction The best way to describe it is that when I was vacuuming I could see dust clouds at the front of the vacuum where the light is swirling around in the air. It was like it was blowing dust around instead of picking it up. I checked the tubing and found that it was clogged with some paper and hair ***** etc.... So I cleaned it out and tried it again and it still was not picking up properly. I had my husband take all the tubing apart to check for other clogging and there was none. When I


You have an airflow problem. You may still have a blocked intake or tube, also check the filter. The air is supposed to go in the bottom (of course) and I'm sure you k**w where it goes out. You probably can **te a reduction in exhaust. If this is ... Oreck XL Ultra Bagged Upright Vacuum

Hoover SteamVac Model F6056-900 SteamVac/SpinScrub. Indicator light and high pitch suction noise indicates that dirty water tank is full. However, water level indicator (yellow bobbing plastic thing) is at the bottom of the tank and there is no water in the tank. Have check all the hoses for clogs, none found. Checked water port from motor area to receptacle tank for clogs, none found. Fixed broken hose to upholstery wand with duck tape, (wire not broken, just cracked plastic hose). The onl


There are 2 filters, make sure they are clean, one is on the tank lid, the other is from the bottom, it is red, pull it out and clean it. If yours has a foam filter on the tank lid covering the yellow ball, make sure there is at least a 1/4 in. gap ... Hoover Vacuums

Help hi there. i have a hoover savvy u8172-900 vaccum. the hose has great suction, but there is limited suction on the main unit and the brush does not spin when i try to use the product. we have cleared the brush of any debris and have also installed a new bag. a few days ago, we disconnected the hose to make sure there was not any foreign bodies stuck in the unit...nothing seems to help. any advise?


As the hose fits into the base (if i am correct) the power at the base should be fine, make sure the base is clean and free from blockage,\015\012you say the brush doesn't spin, has the belt broken, if so replace it, (very cheap) and only a couple of ... Hoover U8171-900 / U8172-900 / U8173-900 / U8174-900 Savvy Bagless Upright Vacuum

Shampooer I have a rainbow e series and my shampooer is not working. The tubes do not seem to be clogged and it sounds like it is trying to work but we cant get the water to come out. We pull the trigger and nothing no soap, no water, nothing. Can anyone help?


Aqua mates have an o-ringed valve assembly that go bad regularly reccoment having it replaced by local vac shop ... Rainbow E series Canister Wet/Dry Vacuum

Clogged vacuum Rather stupidly, my boyfriend 1) were vacuuming without a bag and 2) vacuumed up a big piece of cotton from a sofa cushion. And now it's making a horrible noise and I see it vibrating where the tube connects to the machine. When you look inside there's a white thing sticking out but it looks like it's part of the vacuum. If it's a clog, how do you fix it? I tried unscrewing the tray the bag sits in but it won't budge.


You can start by taking off the bottom plate or top cover, which ever comes off, that is where the inlet starts going in and hopefully the clog is there. Could be in the hose also. But without the complete model number I can't look it up to see a p ... Kenmore 31912 Progressive Direct Drive Bagged Upright Vacuum

The bottom bar that encases the brush is flush to the floor when using the vacuum. This causes the suction to "stick" the vacuum to the floor (lamenate) and also as there is no ground clearance debris is just pushed around. We have to nearly stand the thing upright to get the ground clearance to be enough for things to start being sucked up. I have taken apart, re-assembled etc and nothing is working.


I'm having the same problem.  The bottom plate is not level with the floor unless the vacuum is nearly in the upright position.  Its like there should be a spring pushing the bottom plate towards the floor.  Anyone know how to fix this ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Clogged my vacum is clogged and I have tried to unclog it but can't find all of the trap doors. Is there a brochure that would step me through it?


You can call your manufacturer of the vaccuum cleaner and get some help. \015\012 Or try unplugging it and turn it upside down and beging taking it apart. Take the brush out and then work your way to the motor. There maybe something lodged up in by t ... Fantom Vacums FM760 Twister 500DX Bagless Upright Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0752 seconds