Having problems with your Hoover SteamVac F5914-900 SpinScrub Upright Vacuum ?

Tools how to switch from floor to tools.

Answers :

On the front of the dirty water tank is a block that you pull out(don't forget to put it back in when done, or you won't have any suction),\015\012Remove recovery tank front panel
\015\012(F) by sliding it straight up.
\015\0124. Replace panel with converter (G).
\015\012Slide converter halfway down opening
\015\012until it is firmly in place.
\015\0125. Before connecting tube (H) to
\015\012cleaner, make sure black tabs are
\015\012extended by pulling tan collar
\015\012toward tube.
\015\012Open door on hood labeled “Stair/
\015\012upholstery Cleaning Connection”.
\015\012Press round solution tube connector
\015\012onto round projection inside door.
\015\012Press connector collar down firmly
\015\012to ensure that it is fully connected.
\015\012The tank replaces in a hingelike
\015\012manner. Position front of lid
\015\012under tabs (I) on front of tank. Rotate
\015\012lid down onto tank.
\015\012Make sure lid is secure on all
\015\012sides before cleaning.
\015\012For full suction, it is important that
\015\012the recovery tank lid is properly
\015\012secured before cleaning.
\015\012Reverse procedure to remove
\015\012hose and solution tube.
\015\012Raise carpet cleaner handle to
\015\012upright position.
Repair Help & Product Troubleshooting for Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Can't switch cleaning mode from tool to floor

There's a mechanism inside the steamvac that should switch the mode automatically when you press the handle release and pull the handle down for the vacuum mode... it's automatic! it took so long to figure out because I kept looking for the switch wh ... Vacuums

I have a Rug Doctor ez-1 that the vacuum only works through the upholstery tool and not underneath. The underneath vacuum only blows air outward. I have switched the carpet/upholstery switch depending on what function I'm using but still no suction on the floor. Any ideas?

... Vacuums

Tools how to switch from floor to tools.

On the front of the dirty water tank is a block that you pull out(don't forget to put it back in when done, or you won't have any suction),\015\012Remove recovery tank front panel\015\012(F) by sliding it straight up.\015\0124. Replace pa ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Switch from tool use, to floor? - Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Where the HELLis the switch to change from tool to floor use?????

... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

How do we switch from using the steam vac on the floor to using the tools to clean the couch?

Please refer to the User Manual link :\015\012\015\012http://www.hoover.com/pdfs/manuals/F5871900.pdf\015\012\015\012It will show ho ... Hoover F5866-900 SteamVac Deluxe Wet/Dry Vacuum

How do i switch from tools mode to floor mode

... Hoover F6020-900 SteamVac Upright Vacuum

Inside view Hi I need an exploded view of the inside of a Bissell 7901w proheat carpet cleaner. Broken Pieces fell out. What connects from the inside of the floor to tool switch and to where? Thanks Gary

Found what I( am looking for. Thank you ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

Hoover U5280-900 upright bagless vacuum twin chamber has a broken slider (switch) to go from tools to floor and carpet--what is the part called?? Indicator knob or cam activator?? where to order it??

... Hoover Windtunnel Supreme U5280-900 Upright Vacuum

How to switch from tools to floor on hoover widepath 6500? no manual


Is there a switch to turn-off the tools so that

On the Hoover U6311-900 there is no switch that turns off the suction to the tool hose. That hose is attached to the head of the vacuum on the side via a spring loaded "door". Just twist the hose to remove it, the door will close and you will have fu ... Hoover U6311-930 Power Drive Bagged Upright Vacuum

I have a model F602-900 and it show it is in the tool mode. How do I get it to change to the floor Mode?

... Hoover F6020-900 SteamVac Upright Vacuum

I am not getting any water to come out of the floor part or tools

Hi There!Here is a PDF link for a Bissell Service Center Repair Guide. Hope it helps! Juli ;)newzealand.bissell.com/images/IncludeContent/Service_Center_Help/Upright_Deep_Cleaner_Repair_Guide.pdf ... Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum

Kenmore canister model 116.25513506 wont turn on. when handle switch is turned to floor. vac motor does not turn on. When switch is turned to carpet, floor nozzle works but vac motor does not. I checked fuse, all o.k. checked continuity for plug, o.k. removed wires for bag full switch...motor wont run. I wired motor directly power cord...motor runs. Thinking it must be the circuit board, how do I bypass it or test it?

... Vacuums

Cannot switch it back and forth from floor to hose

Yes it is sold separate. its called the divertor and can be purchased from bissell or one of there dealers. hope this helps. if you need assistance with the installation i would love to help after purchasing the part. ... Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum

My dyson slim vacuum doesn't switch from hose to floor mode. I thought the foot lever was broken. I realigned it but it doesn't switch now from floor mode to hose mode. I take out the hose and I can see the white part. I thought it should move as you go from upright to recline position of the handle.

The changeover valve is not activating - call the Dyson helpline - they'll set you up for a repair with a repair dealer in your area. ... Dyson Slim DC18 All Floors HEPA Bagless Upright Vacuum - Iron/Titanium/Yellow

Flap My floor/ tools knob won't turn. The knob controls wheather you are going to use tools to shampoo furniture of floors. The flap and knob will not trurn

Most likely the diverter valve is broken part #2136988. You will have to remove the top to replace it. ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

Blocked suction The FLOOR suction line (Hose) is clogged. I Can vaceum the floor, but it will not pick up anything because the hose to the bagless canister is blocked. I can switch from floor to hose and can vaceum furniture. it will not pick up off the floor. I have tried running a wire down/up the hose. I Can feel the blockage, but I cannot get it out. I am afraid to pull the flem hose out as I do not know how it is attached at each end.

Hi,Here is a tip that I wrote about my Bissel ... the hose should just pull out... it is just stuck in there tightly...\015\012Bissell Bagless Upright Vacuum ... Royal 088500 Featherlite Upright Vacuum

Doesn't emit water in either tools or floor mode.

The mixer valve is most likely gummed up with old soap and stuck you will need to take the bottom of the machine apart to get at it. The problem with that is while it is easy to get apart it can be very difficult to get back ... Bissell 1698 PowerSteamer ProHeat Upright Wet/Dry Vacuum

On/Off switch. When the switch is set to "Floor" setting the vacuum will not turn on. When the switch is moved to "carpet" setting the vacuum starts.

Because floor means for lanolium it may have a sensor that detects carpet or linolium ... Kenmore 35821 Vacuum

Just got my dc33... one issue... the dial switch to control btn bare floor / carpet mode doesn't seem holding in it's position when I set to the bare floor mode... it keeps coming back to carpet mode with brush-bar activated... the dial doesn't really click to the floor mode. Any advice on this?

Hi there,I'm sorry to hear you're having difficulties with your DC33. If you're concerned that the brush control doesn't seem to be staying in position, it's probably best if you get in touch with us directly. One of our experts will be h ... Dyson DC33 Bagged Upright Vacuum

Proteam Pro force 1500xp Upright vacuum... When I switch to the carpet setting I have no suction power but the beater bar is turning. If I switch back to the floors setting, the suction is excellent. Wondering if the problem is in the on/off switch?

Just undo the screws on the front part of the switch assembly, carefully check all the leads to the switch. Mine slide off all the time as the switch is poorly designed and subject to damage when the darn thing tips over (easily!!!) new switches are ... Proteam ProForce® 1500XP Bagged Vacuum

CARPET/fLOOR tOOL Electrolux Hoover Model EV4602. Need to buy the plastic connector from stainless steel tube to the Carpet/Floor tool. If necessary buy a new floor tool We live in Cape Town do you know a stockist for spare parts for Elecrolux Hoovers near to us

... Vacuums

Hoover SteamVac Plus 1200 upright hot water extractor Water/carpet cleaner applying o.k. Suction on the "floor" does not work. Suction on the hand tool works somewhat, but water is not collecting in the bucket. There is suction coming from the floor but water is not going into the bucket. It does not appear to be clogged because I can feel with my hand that air is flowing from the floor. The water is not being sucked into the bucket.

... Hoover Vacuums

Floor cleaning / tools or pretreat lever appears to be broken

That grey lever needs to be closed while floor cleaning. You only open it when you use the hose. ... Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0406 seconds