Having problems with your Hoover SteamVac F5914-900 SpinScrub Upright Vacuum ?
My Hoover will not turn on
\015 I was using my Hoover spin scrub hose attachment to clean a spot on the floor. When I went to go back to use the vacuum the water tank was empty. I know there was some water left in that tank when I last used it. I pushed the power button and water began to come out through the bottom of the carpet cleaner the unit turned on for a few seconds then turned off and has not turned on since.\015
There was probably a leak in the hose/piping near the pump in the vacuum that shorted out the motor. you will need a new motor for the vacuum. you will also need a new pump assembly. i strongly recommend that you also replace all the internal tubing and places where the pipes join.
Repair Help & Product Troubleshooting for Hoover SteamVac F5914-900 SpinScrub Upright Vacuum
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
Hoover upright 2000w, HL2005 001 problems:the hoover made a pop sound & turned off. Tried leaving it for 30 mins as suggested in the manual but it still won turn on. Really cannot afford to buy a new 1 & would like to fix it. partner is an electrician so if we have some guidance as to what the problem may be i am confident we can fix it. the hoover is only 18 months old so not very old at all.
Hoover Mach 6 U5198-900 vacuum roller brush won't turn. I had opened the bottom to clean hair off the roller. the belts are not broken. When I closed it and turned it on, now the roller brush won't turn. I can push and turn it by hand, but not easily. Then I noticed the brush on/off switch is turned off, but when I step on it, it won't turn on. I was thinking I let something get out of place when I opened the bottom, but can't see what.
... Hoover Tempo Widepath Upright Vacuum - Blue
The brushes on the Hoover All Terrain Steamvac won't turn. However, when I try to turn them manually they will turn. So, why won't they turn when the machine is turned on?
Some vaccums have a belt on the brushes. might need a new one if it does have the belt ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum
The Vaccum is not turning on when i plug the hose into the wall. The hoover system will turn on when i turn the switch on at the base and wont go off till i turn the switch off. But it will not come on automatically when i put the hose in to the wall connections. Many Thanks Linda
You can test this out by taking a small metal spoon and with the bottom side of the spoon insert it into the vac outlet on the wall. you want to touch the two metal pins inside the vac outlet to test if the unit is the problem or the hose is the prob ... Beam Industries Vacuums
Hoover WindTunnel S3765. The motor spins and the belt turns when I turn the brushes on, and the brushes will spin. The problem is that when I do this on carpet, the brushes stop spinning. As soon as I pull the "head" off the carpet, the brushes spin again. It's almost as if the vacuum suction is too great. I took the head apart and watched the motor turn the metal spindle that the belt rests on, and the belt turns as well.
The belt is stretched and needs replacement.(Belt # 38528036) . The brush is not turning against resistance. ... Hoover Vacuums
My Hoover Platinum LiNX Cordless Stick Vacuum beater bar is not turning. After removing some clogged hair and items...the vacuum cleaner has suction, but the beater bar will not turn. What to do? The belt is still attached and will turn manually.
... Hoover Platinum LiNX Cordless Stick Vacuum
I have a Hoover Turbo EmPower 4600 and the roller will not turn when we turn on the vacuum. The vacuum is fairly new, and hasn't seen too much use, but now the roller won't turn, so it's not picking anything up. There also doesn't appear to be a belt or any way to take this apart. Can you help me? Thank you!
The beater belt is broken. There are 4 phillips head screws on the outside (2 on top of the base on either side of the upright, and 2 on the front edge on the underside of the base near front edge). and 4 phillips head screws on the inside (holding ... Hoover Vacuums
Henry hoover Hi all, I bought a spares/ repairs Henry on ebay having been told there was no cable rewind and believing that since I had a spare one in the shed it would be an easy fix. However, poor Henry had his cable replaced to find when plugged in, he tries to start but nothing happens. The motor turns once and just cuts out. If you turn it on and off again it happens again. One whir and turn of the motor, then nothing. It blew the fuses out in the kitchen first time too, so could it be a re
Hi it can be the connector at the end of the Henry cable inside the cable rewind unit happened to us! ... Numatic Henry Bagged Canister Vacuum
I have a Hoover F5411 steamvac Jr spot cleaner and it won't spray and one of the answers was to turn it over and try to turn the impiller to see if it turns. Where is the impille? Is it on the bottom of the top of the steamvac or on the bottom of the part that takes in the recover water?
I've just installed a hoover central vaccum SH800CA and when i plug the hose in the inlet, it doesn't turn on. It turns on when I turn on the switch on the canister
The hose connects to a set of low voltage contacts inside the top of each inlet. The vac wiring is connected by a low voltage circuit to each inlet as well. your hose when plugged in completes the circuit when you turn the hose switch on. For simplic ... Vacuums
My hoover spin scrub brushes stopped spinning and i have cleaned intake filter and tried to turn the thing that spins it...when brushes are off the hole turns then as soon as i connect brushes the brushes will not turn what else can i do!!???
Kirby G5 I was using the hoover and just switched it off and turned it on again but would not turn on. I changed the fuse in the plug but still wouldnt turn on. what should I do?
See my troubleshooting guide and from there, you can view my do it yourself guides for fixing your Kirby. ... Kirby G5 Bagged Upright Vacuum
I have a hoover steamvac model # F5915-900 and the brushes are not turning when I turn the selector from off to low or high. I've checked to make sure the brushes are locked in place and they turn manually with no resistance. What else can i do?
(1) Remove the brush assembly by pulling/unlatching it from base on each side.\015\012(2) Does one of the brushes have the drive pin present? It should be about ¼ inch square, and two inches lo ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum
The brush on my Hoover Windtunnel T series won't turn when I'm vacuuming carpet. It does, however, turn when I'm vacuuming bare floor, and I didn't think it was supposed to do that.
1) test the belt +brush for worn and replace2) test the motor God bless you ... Hoover WindTunnel TSeries Bagless Upright Vacuum Cleaner UH70107
Hoover SteamVAc LS - brushes turn slowly
... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum
Brushes won't turn on a Hoover F7426-900
There is a turbine that turns from the vacuum pressure your motor creates, its black and shaped like a snail. Take the top covering off, you can do this by removing the four screws situated towards the front of the bottom of the machine. Then there a ... Hoover SteamVac V2 6-Brush Widepath F7426-900 Vacuum
My Hoover will not turn on
There was probably a leak in the hose/piping near the pump in the vacuum that shorted out the motor. you will need a new motor for the vacuum. you will also need a new pump assembly. i strongly recommend that you also replace all the internal tubing ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum
Brushes wont turn hoover 2000 dust master - Hoover Vacuums
Needs a belt visit www.stevessewandvac.com they have on for your unit. ... Hoover Vacuums
George i have just bought George from a friend and he has never used the wet side of things . When i turned the hoover on i cant seem to get the wet button to work. Do i have to have the hoover main button on first and then press the wet button?
The pump can seize up if the the system is not flushed with clean water after using carpet shampoo. You should run half a tank of clean water through Geroge before putting him away.The only solution is a new pump or pump motor. ... Numatic GVE370 Canister Wet/Dry Vacuum
Overheating Hoover My Hoover cyclonic 1800w keeps overheating and turning itself off, not sure if it's the filter, I've cleaned it but it didn't look very dirty.
Most likely caused by a lack of airflow. Check to see if you have airflow at the end of the hose. If not, Remove all of the hoses and ensure that they are not clogged. If there is airflow through the hose; check the air inlet immediately aft of the b ... Hoover U8145-900 Savvy Bagless Upright Cyclonic Vacuum
Hoover 2000W dust manager cyclone- Have had this for about 2 months and the brushes stopped turning thinking that the belt had acme off turned it over to try to get in to look at belt now the bottom wheels have came off and will not go back on have not lost any bits literally just undid one screw! Please help!
... Hoover Vacuums
Brush on my hoover windtunner will not turn - Hoover Vacuums
You belt has probably broken or stretched and therefore not turning the brush. You can find any hoover windtunnel belt at www.vacbelts.com. ... Hoover Vacuums
When I turn my Hoover windtunnel 2 on it turns off immediately.
If you want to give me a call i will understand better what you have 314-628-9153 ... Vacuums
Hoover Windtunnel U5750-900 Agitator brush is weak. It turns fine if I tilt the vacuum back, but it slows to almost 1/4 speed when it touches carpet, even on the highest carpet setting. I've replaced the agitator belt twice. The brush used to turn powerfully even on the lowest (Hard Floor) setting. Ideas? I should probably lube the agitator brush ball bearings, and re-check the belt, but, other than that, I'm stumped.
... Hoover U5750-900 WindTunnel Bagless Upright Vacuum
Hoover on off switch won't turn off. I have to unplug the vacuum to stop it. I have dismantled the handle and now I can't get the inditation in the handle to fit over the little silver knob. I saw there was an on/off switch under the handle that is controlled by a piece of the handle. #1 question for the manufacturer is why don't they put the switch on the outside instead of having gimicks that turn it on and off... arghhhhhhhh
Don't know what model you have, but sounds like you will need to replace the switch. As far as your question, you will have to contact the manufacture for an answer. We only provide solutions to your problem and a model number would have helped. ... Vacuums