Having problems with your Hoover SteamVac F5914-900 SpinScrub Upright Vacuum ?

Cleaning vac to clean out the dirty lint between the front of cleaner, does that part come off. I have a build up of stuff in the suction area


Answers :

It comes off, there is a screw on the top and a screw on each side at the bottom front. But you will need something thin to reach up between the 2 layers of window and get that stuff out. But with it off, you can run water thru it to help clean it.
Repair Help & Product Troubleshooting for Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Cleaning vac to clean out the dirty lint between the front of cleaner, does that part come off. I have a build up of stuff in the suction area


It comes off, there is a screw on the top and a screw on each side at the bottom front. But you will need something thin to reach up between the 2 layers of window and get that stuff out. But with it off, you can run water thru it to help clean it. ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

My 4 yr old Nilfisk vacuum cleaner has been working fine up until now. But suddenly, it has hardly any suction power and also, hot air seems to be coming out thru the vents on top and also thru the space that's normally used for blowing air OUT....the outlet with the retractable cover located close to the part where the power cable comes out of and retracts into. I've checked the filter and the hose and they are not clogged...I have also put in a new bag. Not keen to buy another vacuum cleaner u


Hi there SmartAlec from Nelsonvacuums.com.au here.It sounds like a blockage of some kind. The best way to find it is to set the machine up for normal vacuuming and remove o ... Vacuums

I have a power drive baggless vacuum cleaner...it runs well, but suddenly it seems to have lost most of the suction coming through the hose and floor area. When I remove the dirt container, the suction below it seems strong. I have had it to repair twice--they have tuned it up and replaced all filters and belt. It still does not pick up well when I vacuum or use the hose. Can you help ?


There is something stopping it up,you will have to dissasemble the unit to find the blockage,this is the most likely problem. ... Hoover U6660-900 WindTunnel Bagless Upright Vacuum

I have a Russell Hobbs Power Cyclonic Pets 2000W vacuum and having cleaned out all the parts I can find the suction is almost nothing. It has happened once before but cleared after emptying out all the filter areas. This time it won't. I have only had the cleaner for approximately 4 months so pretty disappointed. can you suggest anything?


I have exactly the same problem, has anyone given you advice? ... Vacuums

I am wondering how I can clean the inside of my bissell spotlifter powerbrush hand held cleaner? I want to clean the part where you suction up - it is full of gunk and hair and I can't figure out if it comes apart or not so I can clean it. Can you help?


Http://www.geeksquad.fixya.com/ThreadView.aspx?prdid=49876&thid=506980\015\012I am wondering how I\015\012Posted by carriespets on Apr 12, 2008\015\012I am wonde ... Bissell SpotLifter 1716 Bagless Handheld Vacuum

I cleaned out my brush in the bottom front, cleaned out the small tubing going into the canister, and the canister itself. I also changed the filter.I snapped everything back into place, but Since then, it doesn't seem to have any suction and there seems to be a space between the canister and the bottom of the vacumm where the canister sits. At that area, you can feel air coming out when trying to vacumm and it just doesn't pick up, it seems to be just blowing stuff around.


You need to really look at it some thing is out of line you shooed not have\015\012any spaces in the top or bottom\015\012pull the canister back out and look at the pins that you lined up with the\015\012to ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Bissell 2x has suction coming out of the "base" part(when I put my had over the rubber ring that leads from base to the handle part there's suction), but there's no suction coming out of the hose. I'm not certain if there's a clog, 'cause I can't get the hose off.


... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Poor suction...continued Wow, thanks for answering so quickly! To answer your question, yes, there is suction at the screen, but it is very weak. I keep that screen clean. As a side note, I noticed that when I remove the top clear plastic cover (that would be part # 37 on the diagram, as far as I can tell) there is decent suction coming from the intake there--part 36? 30? it's hard to tell. But with the cover on, I feel no suction (from where it sucks up the water directly from the carpet),


Wish I had it in my shop, it is hard to figure your problem. I do know that you must have something out of place and you may have to take it apart to find it. You may feel some suction there at the top of the clear nozzle, but maybe it isn't strong ... Hoover F6212-900 / F6215-900 SteamVac Agility Upright Vacuum

Mystery part Bissell 1699-P. I removed the top cover and a part came tumbling out (from the rear of the machine - towards the handle area). I have no idea were this part belongs. I have a schematic of the cleaner but I can not locate the part on it. I tried to copy and paste a picture of the part but that isn't working so I will attempt to discribe the part: There is nothing stampted on the part that I can see. It is plastic(white), 2" long, 3/16" in diamater. One end is U shaped (u-shape is 1/4


One question... you haven't mentioned that the vacuum doesn't work now... as hard as this is to accept... if it doesn't effect the function... forget about it.... i could very well have been something you vacuumed up along the way.\015\012 ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

Burning smell coming out while using a Hoover's upright vaccum cleaner (model U6434900). Replaced both flat and v-belt. The problem appears to be coming from near the motor area. The manual does not provide any information on how to reach that area. Any help will be appreciated.


Took it to a manufacturer's repair center. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

I have a Bissell Proheat steamer carpet cleaner. There is a red L shaped part that says hips on it that I do not know where it goes. It also does not have any suction. Is the part the cause of the loss of suction and where does it go?


Http://thefuntimesguide.com/images/blogs/bissell_water_container.jpg ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

Have Dyson DC 14. When tilt to vacuum, the handle and coiled hose comes away from the unit. The problem started when the little purple ridged curved part on front of vacuum cleaner right below handle came loose and a spring fell out from somewhere--don't know where. I pushed on the purple ridge part and it snapped back on. Now, can't get it loose again, don't know where the spring goes, and handle still comes loose from vacuum.


I'm not positive whether or not this is the wand handle because there are several versions of the DC14. However the device the locks and unlocks the wand in place is pretty similar between all the versions.The first picture is the wand re ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Poor Suction Heya! So I just picked up a used Dyson, but when I vacuum with it, the suction is pretty weak and it spits all kinds of stuff out the back and into my feet. When I pull the hose I have good suction, but in regular mode it hardly picks up anything. The brushes are spinning, and it eventually will clean an area if I go over it again and again. Maybe a clog somewhere? Please tell me that Dysons have better suction than my $50 Dirt Devil! Thanks!


I recently bought a second hand Dyson DC07. Its suction was poor. I removed all the un-clipable pipe bits and to remove any blockage but it all looked clear. The Final Sponge and hepper filter did have a lot of dust in it and the rotating brush was f ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Parts Hi I have the Eurkea steam cleaner model 2450 and was wondering how do you take the front part off where you can see the water sucking up from carpet so this can be cleaned. Also I think the spring in the part that holds the water has come off another part is this able to be fixed or can I just purchase a new water holding tank and if so where? Thanks


Click this link for spare partshttp://www.vacpartswarehouse.com/Eureka-2450-extractor-s/1802.htm ... Vacuums

Hoover SteamVac Plus 1200 upright hot water extractor Water/carpet cleaner applying o.k. Suction on the "floor" does not work. Suction on the hand tool works somewhat, but water is not collecting in the bucket. There is suction coming from the floor but water is not going into the bucket. It does not appear to be clogged because I can feel with my hand that air is flowing from the floor. The water is not being sucked into the bucket.


... Hoover Vacuums

I have a Dyson DC07 animal ( purple). If you are standing behind the vacuum I am missing the lower righthand connection...therefore whatever is suctioned up comes out at that point just over the back wheel. I would like to purchase a replacement for this part. In the manual I believe this part is labeled as C. Can this part be purchased separately ?Please Help....


Hi there SmartAlec from NelsonVacuums.com.au i am not sure if you are based in australia but if you are you can ... Dyson DC07 Bagless Upright Cyclonic Vacuum

I lost the detergent container on my Hoover Model F7220-900. Its a small plastic bottle that sits on the back of the clean water tank. I called the help desk and they told me that they no longer make that part so I have to pay $55 to replace the whole tank which will come with a detertent container built in. The whole carpet cleaner was only worth about $225 new. I don't feel I should have to pay $55 for a part I don't need but the machine is worthless without it. Any good ideas to solve th


... Hoover F7220900 SteamVac V2 Upright Vacuum

When I squeeze the trigger, water won't come out of my Bissell PROheat2X carpet cleaner. The beater bar rotaotes, and there seems to be suction. Nothing comes out the bottom.


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

The last time the vacuum cleaner was used the outlet sparked causing it to smoke when turning on vacuum cleaner. I replaced the outlet and plugged it in and things seemed o.k. Today I turned on the vacuum, it stayed on for a mili second and went off. I checked the switch on the vacuum and it showed voltage coming and going, but would not turn on again. I checked all the wires in the area of the switch all seemed o.k. I thought maybe there might be a short in the cord. When I went to plug


... Sharp Twin Energy EC-12TWT4 Bagged Upright Vacuum

The Neutral/drive pedal fell off our Kirby G5 vacuum cleaner. I opened up the area housing its connection to the transmission and a couple of the parts were just laying inside. I need a diagram for assembling it and see if I am missing any parts. It was a refurbished machine and a paperclip fell out of the housing when I opened it. Can you help me?


Hi,In the below links you have the parts diagram as you asked will this helps you?If not let me know i will help you more.http://www.fiorijanitorial.com/s-19-kirby-parts-and-bags-generation-3456.aspxhttp://www.vacu ... Kirby G5 Bagged Upright Vacuum

Replacement part i broke a piece of plastic off my furniture attachment and now it will not spray cleaner or suction. can i get a replacement and will it suction again?


Http://geeksquad.fixya.com/ThreadView.aspx?prdid=430575&thid=830386\015\012Replacement part\015\012Posted by blassx3 on Jul 25, 2008\015\012I broke a piece of pla ... Hoover F5906-900 Upright Steam Vacuum

Bissell 8920 proheat x2 brushes not turning i only noticed this after i finished cleaning.. or kinda cleaning because of the brushes ntot turning.. water comes out fine suction is fine but its not scrubbing so its not as clean as it could be. manual part works well water coming out hot. I did take it apart and cleaned off all the hairs in hopes maybe that was it.. put it together still nothing.. No idea how the belts should look onit and i cant find a picture or a video showing how belts look o


Hello,\015\012\015\012Here's a link to a very helpful video that shows you step by step on how to access and replace the belt on your machine. When the brushes stop spinning, but the rest of the machine works fine, this is a tell-tale ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Water is not being discharged. I have filled the reservoir that holds the carpet cleaner fluid And I have filled the water container. I know how to use the cleaner, it has always worked, But now, no water is being discharged to the carpet. I turn it on, squeeze the trigger, but nothing comes out. The wheel that is suppose to spin (to indicate that water is being discharged) is not spinning. Everything else works. I.e. the suction works, and the hand held accessories work.


That means that the pump belt is worn and it needs to be replaced. You can get a replacement belt and view the manual here:Bissell Pump ... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

I get plenty of suction at the hose, and none at the brushes. Also, the vacuum will not remain upright when I push it up. It appears that the part that switches the suction from the hose to the brush area is not engaged.


I looked up the problem where the machine would not stand upright, used that solution, and it worked. ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

I built a new house nearly a year ago but didn't move in until recently. The Nutone central vacum system doesn't have much suction. I've tried different things but am afraid there is a break or breaks in the system. My question is how can breaks or joints that come a part in the suction system be located so I will know where to cut into the wall.


Hi,\015\012\015\012Here I am giving link of manual which shows how to install the your gadget.\015\012http://www.retrevo.com/support/ ... Broan-NuTone VX475 Bagged Central System Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0820 seconds