Having problems with your Hoover SteamVac F5914-900 SpinScrub Upright Vacuum ?

HOW TO I clean the front plastic panel?

\015 I'm unable to remove the front plastic panel where the water is sucked through is there any trick to it? it's so filty I have a small baby and had to clean his room after him (vomit) but seems like most of the ugly dirt is stuck there, please help...\015

Answers :

In addition to those screws you have to remove side light screws and screws holding the brushes. Then it comes off.
On mine there is a screw at the top and 2 at the bottom of the panel take those off and the panel comes off to clean.
Repair Help & Product Troubleshooting for Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

HOW TO I clean the front plastic panel?


In addition to those screws you have to remove side light screws and screws holding the brushes. Then it comes off. ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Need front panel Small Plastic Part For Dirty Tank Holder


... Hoover F5906-900 Upright Steam Vacuum

My roomba won't go forward; it just rotates right ~90 degrees and then left ~90 degrees. I've cleaned the brushes, taken it apart and cleaned the brush gears, popped off the front wheel and cleaned the hair off that, taken off the front bumper panel and cleaned off the cliff sensors. Please help!


Compare your Roomba to the video on http://www.eesolutions.ca and look for the fix. ... iRobot Roomba 550 Vacuum

The removable filter at the front is cleaned regularly, and is not clogged. However, the machine appears to be suffering from being clogged by dust, as it has started to make a high pitched noise, and I fear it may burn out. I can see some dust inside the front panel but cannot see how to remove the front to clean it out. (NB. I have located two screws - one on either side - but cannot see how to proceed further.) Please help! Thank you.


\015\012\015\012Hi,Here\015\012is a tip that I wrote about my Bissel but I bet you have the same\015\012problem and the hose is clogged...Bissell Bagless Upright\015\012 ... Vacuums

I want to clean fluff from underneath the transparent front panel of my Bissell 11 7901. I have removed the screws from the bottom of the panel, but it remains firmly in place. I do not want to apply apply forceful leverage in case there is something else that needs to be done before the panel will come off. Any suggestions, please? Peter


I just did this one myself, You've done most of the hard work already.Be sure your holding tank is out and not in the way.Double check the down front screws are still out since you sent in you question. Now tweak the front section (the business end) ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

How to clean clear plastic thing in front of Bissell ProHeat?


You may have to run it to soften the hair, then you should be able to go under it with a rag to clean it. ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

How do i remove the front of the Proheat Clearview to clean it out? I removed the two obvious screws at the front sides of the clear plastic part but see anything to remove to take it off.


... Bissell 1699N ProHeat Clear View Force Upright Vacuum

How to dismantle a Miele S 5980 vacuum cleaner. The RESET switch has fallen in and I can't remove the plastic panel to replace it. Neither can I remove the cleaner body to get in from beneath. I have removed 2 screws from the front of the barrel (nozzle end), one screw centre front, two screws towards rear, but there seems to be something else holding the housing together. [email protected]


... Miele Vacuums

When i removed the bottom panel to clean out the roller brush, the front wheels fell off. I can't figure out how to put them back on!


I( think Dirt devil wheels are held on by a little clip, kind of round ish. Check the other wheel and see if it has that kind of set up. Chris ... Dirt Devil Featherlight Bagless Upright Vacuum

How do you take off the clear plastic piece that covers the brush on the front of my dyson animal so I can clean it?


What model is it ?you can download the manual from the link below.http://manchestervacs.co.uk/DysonForum/index.php/topic,2.0.html ... Dyson Vacuums

Question-can I purchase a recovery tank front panel for Hoover Carpet Clean - F5853-900, series 17.9, serial number 069700345408? I can be reached at (304) 243-3788


Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=675962\015\012Generic problem for all Vacuums\015\012Question-can I purchase a recovery\015\012Posted b ... Vacuums

The lights which tell you if you are going at the right speed on my Bissell PROHeat Pro-Tech have stopped working. Just wondering if this could be as simple as a bulb or more serious. Also, how do you remove the clear panel at the front for cleaning? Thanks


The clear view window is unscrewed with a philips screw driver on either side of the nosel opening (top) but make certain the handle is layed back so as to alleviate twisting off the clear view cover. There are six (6) screws that hold the top cove ... Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum

How to you take off the plastic shield in front? There is a lot of carpet fuzz that I want to clean out. I've unscrewed the phillips screw on top, but am not sure where to go from here.


Go to this site and select the model / type of your vacuum and open the appropriate manual..http://homeappliance.manualsonline.com/ex/thread/view/idThread/1306047good luck and don't forget to vote!!! ... Hoover F5892-900 SteamVac Upright Vacuum

I have a Bissell Steam Cleaner that is not sucking up the water when cleaning. I used a full container of water and when it was empty I emptied out the water, only to find very little dirty water in it. I noticed the window, as i used it, seemed like it wasnt sucking up the water. I took the plastic cover off to clean it (it didnt look very dirty in the first place), an i noticed that the grey plastic flap was on but not moving up or down. I thought there may be dirt in it that prevented it from


... Bissell Vacuums

Water won't spay out of the nozzels under front plastic


There are 6 screw, 3 on each side, then the top will come off. When you put it back on, make sure the piston is attached to the bottom of the smart mix knob and that the knob is in the water setting.\015\012\015\012 ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

I HAVE LOST MY INSTRUCTION BOOK FOR THE STEAM VAC SPIN AND SCRUB. I WANT TO USE THE STAIR ATTACHMENT, BUT I CAN'T FIGURE OUT HOW TO HOOK IT UP, OR OPERATE IT. I SEE WHERE THE PLUG IN PART GOES IN THE FRONT OF THE MACHINE, BUT I CAN'T GET THE OTHER PART TO SLIDE INTO PLACE ON THE FRONT OF THE RESOVIOR TANK AFTER I REMOVE THE FRONT PANEL, AS THE DIRECTIONS ON THE FRONT OF THE RECOVERY TANK SAY TO DO. THE FIT IS JUST TOO TIGHT. WHAT AM I DON'T WRONG- OR HOW COULD I GET A REPLACEMENT INSTRUCTION BOO


You can download a PDF version of the manual at the link below. I believe you can contact Hoover as well and they might mail you one.http://www.hoover.com/CustomerService/Manuals/Default.aspxGood Luck! ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

I cleaned out my dyson ball as it smelt when i hoovered, cleaned filters, washed out canister and took the screws out of the front bar so i could clean near the brushes.. now its making a high pitched noise and when i switch it off it makes a noise like an engine shutting down! Have i disturbed the motor?


Hi its Darran at Dyson. The screws on the base of the cleaner head should not have to be removed to access the brush bar so it is possible that the brush bar has come out of alignment, hence the noise the machnie is making. Pl ... Dyson Ball DC24 Bagless Upright Vacuum

The dirt is clogged inside the bissel little green 1400-7 hand held cleaning head. How can I unclog? Can the plastic piece be removed asw for the dirt is stuck on the sides of the cleaning handle?


... Bissell 1400 Little Green Pro Canister Steam Vacuum

My Kirby 2HD has started making an odd roaring noise but still works fine. I have taken the front assembly off and cleaned and adjusted the roller and checked the belt. The noise seems to come from the motor housing. I have tried to wiggle the main shaft at the front (bearings?) and it seems tight. Can't seem to get the other housings apart. Any ideas? Thanks, John


It is quite possible, it just needs lubed. The motor comes in direct contact with dirt so, you have to make sure the front bearing has a drop of oil on it from time to time. If it starts to scream at you within one month, after oiling, the bearing ... Kirby Heritage II Vacuum

My roomba won't go forward it just spins in a circle and will go backwards. I have already tried cleaning it out and cleaning the front bumper sensors.


This is the Circle-Dance Error. I had the same problem. I just ordered a repair kit from EESolutions.ca and did the fix myself. Works like new to this day. ... iRobot Roomba 530 Robotic Vacuum

I have Optima, 12amp Eureka vacuum, Model 431, AXZ type and the extension hose for cleaning corners and edges --the plastic part that the attachments fit into has a piece broken off and tools don;t fit anymore. It looks like the hose attachment can be replaced--can it be and if so--where can I get a new hose attachment. It seems it is cheaply made of plastic and really shouldn't have broken a piece off.


... Eureka 431A Optima Bagless Upright Vacuum

How to clean the unit? The clear suction part in the front gets filled with fibers and other **** and I don't know how to get it cleaned out without breaking it. Any suggestions?


I use a knife blade or nail file (metal ones you get at any drug store) to get the fibers out. With new carpets it's a mess - have to clean the bottom of the unit as well as the brushes and up inside the area where the brushes are housed. Otherwise ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

I'm trying to clean the brushes under neith and trying to figure out how to take to plastic part off so that i can clean underneith. I think the brushes come out but i'm not sure how.


The brush block wasn't made to take apart and clean. The whole block will come out, it just cames catches that hold it in place. ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

Hi my beater bars will not turn anymore, i have tried to reset it cleaned the bars removed and cleaned the front wheel, but still they will not turn.Any help would be appreciated


Belt has probably broke in the power head ... Vacuums

I have a new Euro-Pro shark model S3101. Used it one time and while I was doing my tile floor in my kitchen I reached under a cabnet to clean and hit the floor kick kind of hard and broke the head off of the shark. I have only the T shaped end on the shark now with the cleaning head broken off and looks unrepairable. I did kind of hit the floor kick hard but the plastic broke like glass. Can I put a new head on the remaining piece or is it repairable? thanks Angie


Hi,Here is a tip that I wrote about the Euro-Pro Shark Steam Mop and why it maynot be getting steam to the head...Euro-Pro Shark Steam Mop Pro ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0482 seconds