Having problems with your Hoover SteamVac F5914-900 SpinScrub Upright Vacuum ?
Brushes don't turn
\015 My steam vac works well except the burshes don't turn. Have checked all filters and they are clean.\015
I Had the same problem, The brushes are operated by water pressure. Under the machine were the brushes are is a white peice of plastic pull this out and try cleaning the screen. I found this when I removed the cover and lubricated the gears at the brushes, If that does nto work you will have to remove the turbines and lubricate.
Repair Help & Product Troubleshooting for Hoover SteamVac F5914-900 SpinScrub Upright Vacuum
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
Dyson dc07 The rotating brush on the bottom of my vacuum was filled with strings. I removed the brush by undoing all yellow plastic screws from plate. Removed all strings and replaced as best I could and it was hard to get the brush back in and the belt around it. I dont have my manual but it fits so it should be correct....? Right? No, not true, because when I turn it on and try to and vacuum (by lower canister with foot release) it makes that terrible ratching sound). Please help
The loud ratching is a warning to tell you that there is something stopping the roller bar from rotating this is a very common thing lay the machine on the floor front side down take off the bottom plate and just check the belt is in the centre of th ... Dyson DC07 Bagless Upright Cyclonic Vacuum
My vax all terrain carpet cleaner brushes dont turn why?
Brushes dont turn
Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 8930M Upright Steam Cleaner
Kenmore progressive model 11635922500 brushes dont turn
... Kenmore 31912 Progressive Direct Drive Bagged Upright Vacuum
I HAVE NO SUCTION COMMING FROM THE BOTTOM OF THE CLEANER AND THE BRUSHES DONT TURN DOES NOT PICK UP ANYTHING WHEN ITS UPRIGHT. BUT I DO HAVE SUCTION THROUGH THE HOSE. THANK YOU
Hi there,\015\012\015\012Sorry to hear you're having difficulties with your DC07. If it doesn't seem to be picking up as well as usual, it's possible that there's a blockage in the system, and you may need to give the filter a wash. The easiest way t ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
The switch seems to have a problem I push it on and it doesn't stay on even if I hold it on the brushes dont turn how do I fix this??
... Dyson DC28 Animal Bagless Upright Vacuum
Panasonic upright vacuum brushes dont turn - Panasonic Bagless Upright Vacuum Cleaner MCUL915
This may be too obvious, but do you have the Carpet switch turned on (bottom left of vac). Agitator brush does not go around if Floor/Tools is switched on, ... Panasonic Bagless Upright Vacuum Cleaner MCUL915
My Hoover Dust Manager roller brush is not turning It may be the belt but I dont know how to get to it to replace i Can you help Michelle
... Hoover Vacuums
My roomba will not go forward. it will turn in a circle for a few seconds then shut off with the red light flashing. i cleaned the brushes and the wheels. i dont know whats wrong with it.
... iRobot Roomba 530 Robotic Vacuum
The vaccum turns on but the brushes dont spin, and i have hit the reset button on it already...
Vacuum turns on and sucks but the brush does not spin and I have pushed the reset button ... Dyson Slim DC18 All Floors HEPA Bagless Upright Vacuum - Iron/Titanium/Yellow
Brushes in roomba dont turn - iRobot Roomba 560 Robotic Vacuum
... iRobot Roomba 560 Robotic Vacuum
The gear that turns the dual brushes on my Bissell Spot Lifter 1716 seems to be stripped. The belt looks loose as well, but when I take the belt cover and the brush assembly out, the gear that turns the brushes is loose and appears to be stripped on the cogs. When I turn the machine on the belt turns the gear but the brushes just sit there an vibrate. They make an attempt to turn now and then but not much. Need to get a schematic or the parts so I can order the gear if it is available and th
... Bissell 1716 Spot Lifter PowerBrush Bagless Handheld Vacuum
Hoover Mach 6 U5198-900 vacuum roller brush won't turn. I had opened the bottom to clean hair off the roller. the belts are not broken. When I closed it and turned it on, now the roller brush won't turn. I can push and turn it by hand, but not easily. Then I noticed the brush on/off switch is turned off, but when I step on it, it won't turn on. I was thinking I let something get out of place when I opened the bottom, but can't see what.
... Hoover Tempo Widepath Upright Vacuum - Blue
Hoover WindTunnel S3765. The motor spins and the belt turns when I turn the brushes on, and the brushes will spin. The problem is that when I do this on carpet, the brushes stop spinning. As soon as I pull the "head" off the carpet, the brushes spin again. It's almost as if the vacuum suction is too great. I took the head apart and watched the motor turn the metal spindle that the belt rests on, and the belt turns as well.
The belt is stretched and needs replacement.(Belt # 38528036) . The brush is not turning against resistance. ... Hoover Vacuums
For some reason, when I tried to put the floor vacuum attachment back on and vacuum the carpet, I realized that the belt was not engaging. the belt is in there and not broken, but it is not turning the beater brush. it is just hanging loose around the brush. When I turn the wheel to engage the brush, it picks the belt up, but when I attach the vacuum to the attachment, the brush is just not turning.
... Kirby Ultimate G Bagged Upright Vacuum
My hoover spin scrub brushes stopped spinning and i have cleaned intake filter and tried to turn the thing that spins it...when brushes are off the hole turns then as soon as i connect brushes the brushes will not turn what else can i do!!???
Rotating bruch My vaccum brush will not turn. This happened after sucking up a cord that wrapped arou8nd the brush. I was able to pull the cord back out but now the brush will not turn. The vaccum does turn on an sounds like it is working with no soinning brush.
Take off the bottom cover where the roller brush is a few screws should be all it takes underneath cover should be roller and belt if belt is broke replace it lift up roller there is a slot for the belt to run in put other end should be the motor sid ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum
My Bissell Model 3760-4 is not working properly. The belt has been replaced (and checked 3 times), but the brush bar does not move when the brush motor button is on. The little metal turning piece that turns the belt is turnable with one's finger when the belt is off, but when we put it all back together and turn on the vacuum, the brush bar does not go around and the burning belt smell returns. The portable part of the machine works properly. It's the brush bar. It has been cleared of hair, etc
... Bissell Lift-Off(R) Revolution(R) Turbo Upright Vacuum
My Dyson Blueprint bagless rollerball vacuum brush refuses to turn every so often. Everything is connected properly, nothing is clogged in the brush, the vacuum power is turned on and then the brush bar control is released, but the brush still does not turn.
... Dyson Vacuums
Kenmore Canister Vac, Progressive, 25512 255513 model. Brush won't turn. One end of the brush roller, end closest to belt, is off center which is keeping it from turning freely. The end cap is like a square. Other ends turns fine. Do these end caps come off? If so how? Can't get it to budge. This is exactly what is keep brush roller from turning.
Take a flat head screw driver and pry the end cap off. It will come off. You might have some string or hair around it causing it to not turn. ... Kenmore 25512/ 25513 Progressive Canister Vacuum
LlllSteam vac ws working very well--shilfted to using hand vac on furniture--when I shiftead back to wanting to use the floor vacuum using the 6 brushes and the floor vac system, the r6 rotaty brushes will not turn or function. What do IO havae to do to get them to turn and function? The lever on the side ils set for carpet terrain. What do I do now to get brushed to turn and scrub as they should and did previously. James Yerges 1'630-232-2798 JMYerges&comcast.net
What is the exact model number of that unit. There are several with that name. The only things that it could be are the handle mechanism that activates the brushes or the indicator is not working nad the level that selects the brushes is not working. ... Hoover Vacuums
Stopped running My mother's Oreck vacuum sound as if there was something bogging the rotating brush down. I pulled the bottom cover off and found nothing wrapped around or restricting the brush. I tried to finish vacuuming with the problem then I turned it off to move a chair and turned it back on it would do nothing. Any suggestions as to what could be causing the vacuum to sound as if the rotating brush is being restricted from turning. There was not odor of burning as if the motor was in a bi
Orecks have a plastic fan inside and everything you pick up hits it, sometimes things can get stuck in there or break the fan locking up the motor. With the machine off, poke around where the dirt goes into the motor, behind the roller and see if you ... Oreck XL Ultra Bagged Upright Vacuum
Now that I just fixed my Lux Legacy canister vacuum, I need help on my other Electrolux Regency Series upright! The vacuum works fine but the rotating brush does not work and the brush motor does not turn on. Tried cleaning the brush and hitting hte reset button to no avail. This upright has a triple setting switch and I checked the each of the wires seem to be attached. Tried rotating the brush by hand and it would not budge. Was going to "encourage" the brush to turn with a set of articula
There are a couple rectangular holes on the bottom of the power nozzle, beside the wheels. These have tabs in them that need released with a standard screwdriver. \015\012 ... Vacuums
Brush will not turn on on my Bissell Healthy home vacuum, the brush button is depressed and brush is clear. The vacuum motor works fine, just the brush will not turn on. Is there a part to replace?
... Bissell Healthy Home HEPA Bagless Upright Vacuum - Metallic Blue
The brushes spin very, very slowly and stop altogether sometimes - like they just don't have any power behind them.I've cleaned the brushes and also turned it on without the brushes inside to see if the female plug that the brushes go into turns - it does, but not very fast. My husband said he thought he smelled something - like burning. Is there a way to take the underside cover off and clean something?
... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum