Having problems with your Hoover SteamVac F5914-900 SpinScrub Upright Vacuum ?
Hoover steamvac spin brush puts out water, won't pull it back up. Checked all parts, no cracks. Cleaned filter.
Check for the front panel duct located on the lower tank front. this is the part you need to remove to attach the hose. also check to make sure the lid is on and secure on the lower tank. remove the lower tank and look on top of the motor cover toward the left front corner you should see a round black gasket on a pipe. if not there, this will cause poor suction.
Repair Help & Product Troubleshooting for Hoover SteamVac F5914-900 SpinScrub Upright Vacuum
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
Hoover steamvac spin brush puts out water, won't pull it back up. Checked all parts, no cracks. Cleaned filter.
Check for the front panel duct located on the lower tank front. this is the part you need to remove to attach the hose. also check to make sure the lid is on and secure on the lower tank. remove the lower tank and look on top of the motor cover towar ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum
No suction I have the central vac type. It has no suction at the can. I pulled the hose going to the walls and tested there...and nothing. I removed the dirt can and checked the motor ...it is spinning but does not feel like any suction. I checked the exhaust and it is pushing strong air out. I also cleaned the filter and still nothing. Is there a relay or something that would cause only exhaust air. I emptied the can of dirt and put it back together and have absolutely no air.....hear the motor
On some units there is a screen that protects the impeller of the motor. If this gets sealed off with debris then it is like putting a potato in the tail pipe of a car. Taking the top off the unit reveals the motor. DO UN-PLUG the unit first from th ... Electrolux Central Vacuum
I have a Dyson DC14 It started making a high pitched squeel so I took the filters out and cleaned them and i checked all places that pull out on the vacume to see if there was anything clogged. I also cleaned the roller brush. but when I turned it on, after a couple of seconds the sound came back again. can you help
Sounds like motor bearings are gone .... sorry. ... Dyson Vacuums
I have Hoover Widepath Bagless 12 Amp Windtunnel vacuum. Yesterday I was vacuuming and smelled smoke and it shut itself off. Today I cleaned out the filters (they weren't bad) made sure nothing was obstructing the hoses or the spinning brush part. It turned on for 1 second, smells like smoke somewhere from the bottom and now won't turn back on so I don't know if anything is spinning or not. What can I do to fix this myself?
Hi There,\015\012\015\012When a vacuum cleaner smokes, it is usually only one of two possible problems.\015\012\015\012It could either be that your motor burned up, or that your belts burned. The belts on this particular mod ... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum
Replacing filter Got a Filter Queen Majestic vacuum from my inlaws when they moved overseas. I am in middle of vacuuming, got a weird noise, so opted to check and clean the filter for first time. UGH. The lower 'pot' that's the bottom part of the thing was full of gunk, but the filter pristine clean against the cone that's attached to the upper part of the unit. In other words, I am shocked to see that the dirt goes not INTO the filter, but outside of it into the bottom portion (that I call the
Its normal operation so don't worry ... Filter Queen Majestic Canister Vacuum
I have a Kenmore 116.36932 (upright-bagless vacuum) that the motor protector by-pass valve has opened. I've clean out the area between the agitator brush where the flexible extension hose starts. There was some blockage there. I checked the rest of the system (extenstion hose, back filter area, pipe area to canister and area to side filter. I took the 2 filters out and the by-pass valve is still open. Where else could there be a blockage that I can take apart to clean and put back together
No Water My Bissell rug shampooer does not eject water or saop whan I pull the saop trigger on the handle. I checked both filters and they are clean. Then, I removed the container that sucks up the water and pulled the saop trigger, water barely came out of the tubes. I tried to clean the rug in our family room and the rug was not wet when I finished, no water coming out to clean the rug. HELP HELP HELP!!! I live in Colorado is there a Bissell repair shop near Denver, HELP!!! Thanks Dominick ema
Does water squirt out of the hose nozzle, if it does, then check the heater inside the handle asm. Make sure that where the tubes hook up to it are not clogged. If water doesn't squirt, check for the seal at the bottom of the tank, it needs to be o ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum
Hi, There is a high pitched whirring sound coming from lower part of the vacuum. When I tilt it toward me (while standing in the normal vacuuming stance) the sound sometimes lessens for a minute or so. I have tried the following things: -cleaned the two sponge filters -emptied the dirt receptacle -removed the roller and cleaned it -cleaned the brushes -the belt is not ragged and does not seem floppy -checked all of the airways for clogs (including removing the wheel base) Can you help?
Your looking for some dirt stuck in some thing you didn't check yet. with the roller out and the belt out of the way run it to see if it still makes the noise. if it does then you looking at the impeller or the motor bearing themselfs those bearin ... Bissell 3750 Lift Off Bagless Upright Vacuum
Noise Hi... I was doing normal house work and had been using it on carpet... I put it on floor for my hardwood floors and picked up loose clean cat litter and went to put it back on carpet and it made a horrible noise like it was rubbing. cleaned the filter... cleaned the roller thingi ...checked the belt and it is still making that horrible noise. It does not make the noise when I have it on floor but as soon as I put it on carpet it screams at me. Help! Please and thanks Linda
Hi Linda,\015\012Sounds like clutch problems, try to move the lever for carpet/floor back and forth a few times maybe it will free up. If it still makes the grinding noise, the clutch assembly will have to be replaced. Let me know, i can even ... Dyson DC07 Bagless Upright Cyclonic Vacuum
Have ultra vision and have changed filter and foam filter, checked all hoses but still will not pick up. Belt is fine and brush is clean and spinning properly. dirt stays at top of filter instead of falling into canister.
My kids get mine stuck all the time :(Take the vacuum outside then:Remove the hose at the bottom and see if there is any obstructions. Also shake the hose to make sure there is nothing in there as well or take it out side and make s ... Dirt Devil Vacuums
Def no choked probs, as I check and clean filters regularly, but when switched on there seems to be a short whineing sound before returning to normal, and def wont lift fluff etc., just runs over it, although ther seems to be a fair amount of suction. It does clean but not properly
Hi, this is Jack at Dyson.\015\012\015\012You should be able to resolve your problem by following these simple steps: http://www.dy ... Dyson Ball DC24 Bagless Upright Vacuum
Hoover steamscrubber I loaned my vac to my daughter who used it to clean shag carpet with lots of dog hair......now the scrubbers wont spin I have taken them (scrubbers) out and cleaned the vac....don't know where the lint trap is...but i DON'T see any part moving that would make the spinners rotate either Thnks...Lydia
I had the same problem. Fixed it by taking the machine apart and lubricating the bearing inside the turo tunnell. It's a pain, but not impossible if I could do you can. You must start by taking off the cover. Don't forget the scvrews on the front by ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum
Dc07 problem I have a dc07 cyclonic vaccum and like this model,however, for some reason,it has been very dificult to push and pull for the past month or so. i have completely cleaned the brush assembly,cleared any obstructions in the hoses,and, cleaned the filter.I also checked the belt tension,wich i thought was fine but to no avail.Be advised that the brush assembly is spinning and suction is excellent. It just feels like the brush drags along the carpeting. this is a great vacuum cleaner and
The dyson uses two belts, one from the motor to a clutch and then from the clutch to the brush roller, the belts that they use are not much better then any other belt ( those you should change yearly ) but you cant just change the belts you have to c ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
Dyson Dco7 animal not picking up from floor. Checked all connection valves and cleaned filter and brushes. Also check tube for cracks and nothing there. Wand suction is great just almost non on floor section. Please help!
I would check the "U" shape tube under wand that goes under body of machine. There is a button to release it. I would also check to make sure that your brushes are spinning properly. When you tip the vacuum back the brushes engage. Carefully place yo ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
When in upright it does not run or when I pull out the wand. I have cleaned the filter and cleared a clog. I turned it on it's side to check brush bars are okay. If I position it for floor vacuum it will run, but again when I pull the wand out it won't turn on.
I have a Dyson Or should say my wife has a Dyson and we suffered a similar problem when it wouldn't run in the upright position but would if we lowered it to say clean under furniture. It turned out to be a fracture in the mains power lead. Upright i ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
I have a Panasonic MCE6003 vacuum cleaner. I regretfully leant it to a neighbour and it came back full of dog hair and keeps cutting out. I cleaned out the dust container and the main filter but it still kept cutting out after 5 minutes. I decided to unscrew the part with the motor and wash the filter inside.It was all going well until a large rubber washer bit, a piece that looks like the thermostat and a little white button attached to two black wires fell out and now I have no idea how to put
... Panasonic Vacuums
Poor suction The actual sweeper seems to work ok, but the hose attachment has some suction but not enough to pick up things I think it should and not enough to make the power brush spin. I've checked everywhere I can for clogs, but I can't see anything. And there doesn't seem to be any way to check to hose itself for clogs. I've cleaned out the container and the filters, but there's still a problem.
Check the inlet down by the brush roll, make sure it is open, if it is then the hose itself must have a clog. If the hose comes off, drop something like a marble in one end and see it it comes out the other end, if it doesn't then you have a clog. ... Dirt Devil M1100009 Reaction Soft Touch Cyclonic Upright Vacuum Cleaner Vacuum
I have a Kenmore Elegance Vacuum with Dirt Sensor, Model # 116.30750400C, Serial number M41901532. When vacuuming the carpet the power head will work for 3-6 mins then automatically shut off, power is still there and lights work but the power head motor turns off and the suction stops. I will turn it off and on, check the outlet, flick the on off buttons...nothing. I will turn it off for a couple minutes and it turns back on and runs like normal. I've check the bags, filters, cleaned the hos
It is an electrical problem in the handle, if you can or know somebody that has any fix it ability it can be fixed in about ten minutes. Oh, and Sears SUCKS!! ... Kenmore 34612 Bagged Upright Vacuum
Hi. I borrowed my friend's Hoover VC340 to clean my house. I was vacuuming when i noticed the cannister was full, so I turned the vacuum off, pulled out the barrell, and followed the instructions on the barrell to empty it. I put it back into the machine, but it wont turn back on. I tried different power outlets, but to no avail. any thoughts?
My son spilled mica all over my carpet. To clean it I used my bissel vaccuum. Now I have orange mica in the removable filter area as well as up inside the part that spins. I need to clean it out, but don't know how to remove it from the vaccuum
Load it into the trunk of your car, take it to a gas station and use the tire inflater hose to blow all the **** out of it.\015\012May have to get a tire stem in order to use it as a blower. ... Bissell 37604 Lift-Off Pet Bagless Upright / Canister Vacuum CleanerVacuum
Sweeper belt Hey , i own a fantom thunder sweeper and recently my belt keeps slipping off, i've disassembled it and put it back on a hundred times but it keeps doing it after a few minutes of cleaning , Am i missing a part to hold it on or somthing else wrong i've cleaned it and checked all the ports just cant figure it out and cant find any info online thanks for your time tina
Greetings from GoVacuum.com,Have you replaced the belt with a new one yet? You may want to try replacing the belt, as with flat belts like the Fantom Thunder, they do stretch out 4 -5 inches after time. We in fact recommended replacing ... Fantom Vacums XT450K Upright Vacuum
I bout this vacume in mid December 07 and about February-March it started not picking up the dust on the floor. So in early April I bout a new filter and it still wasn't picking up the way it had in the beginning. I've taken it a part several times and cleaned it out with it being plugged at the bottom hose with dust bunnies. Well I just took it back to Walmart where I purchased it and I failed to keep the reciet they could not do any thing about the sweeper. I went back to the sweepers and re
Pull the hose out of the holder, is there suction there. If not, then there is a clog in the hose. If there is suction, then check the dirt outlet by the brush roll. Also if the belt is slipping, it may appear to not have as much suction, belts wi ... Dirt Devil Vacuums
Bissell cleanview 11 bagless special edition model 3576-2 I took apart to clean the filters and don't remember howto put the bottom of the dirt container back. I thought I put the empty container back in place correctly but the dirt when vacuuming is flowing through another part of the vacuum.
... Bissell Vacuums
Kirby sentria My roller brush won't spin belt is not broken I cleaned the Roller brush and put it back it. It put it back but it looks like the sensor balls aren't touching the plastic part underneath. The green light Doesn't turn on either. It was just working and it stop picking up out of nowhere this
I have a Dyson Ball vacuum cleaner and slowly the spinning portion of the vacuum ceased to work. We checked for hair, etc. that might be caught but it is all clean. We also checked the filter within the ball portion of the vacuum. Any suggestions would be great!
Hi Antonia. I assume the spinning part is the brush roller. If so, you have a broken or stretched belt. I am not too familiar with the Dyson. I would be interested to know your progress so I can learn also. Thanks Chris ... Dyson Ball DC24 Bagless Upright Vacuum