Having problems with your Hoover SteamVac f 6020 - 900 ?

Hose wand replacement

I am trying to find a replacement hose and wand

Answers :

Repair Help & Product Troubleshooting for Hoover SteamVac f 6020 - 900

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a Miele Vacuum cleaner MedicAir 5000 Plus. Recently the Dust Bag Indicator bar is full during normal cleaning and consequently the suction power is much less. I replaced the dust bag, engine pre-filter and Hepa filter but no change. When i remove the hose, the Indicator is normal, but when i attach the hose, wand, head, the indicator is full. I checked the hose, wand, head but can't see any blockage and when i blow with my mouth it seems fine. Can anybody help? thanks!


... Miele Vacuums

Pls Help! My Dyson DC05 (Yellow) needs a new wand. Am unsure whether it is the assembly wand or hand one found in spare parts. The wand I need to replace connects the two long hoses together, and NOT the wand which fits onto pickup head. M.thks if you can advise which one I need. Getty rather dusty in my pad!!


... Dyson DC05 Bagless Canister Cyclonic Vacuum

The hose does not stay connected to the wand although the collar appears to be locked in place for a while. Is there a replacement part for this? Also the holder where the wand goes in has split horizontally. This appears to be one piece with the body of the unit. Is it repairable? It still holds the wand but continues to get worse.


... Dyson DC07 Bagless Upright Cyclonic Vacuum

How do I replace cleaner supply tubing on tool, I have hose, tubing and wand.


... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

On a filter queen 360 vaccum the electrical connection from the hose to the wand was loose and over time the electrical arcing burned up the female conector piece. Is there any way I can replace this without having to buy a new hose! Where would I find this female conector piece.


I am having the same problem On a filter queen 360 vaccum the electrical connection from the hose to the wand was loose and over time the electrical arcing burned up the female conector piece. This sounds to me like a manufac ... Filter Queen Vacuums

Where can I purchase a replacement wire for the handle of my aerus centralux hose? It's the black wire that runs from the switch in the handle and attaches to the pins in the wands.


Any Aerus Electrolux store should have them in stock.\015\012You can find the one nearest you by following the directions on the below site:\015\012\015\012 ... Electrolux Centralux Vacuum

Where can I get replacement rubber "o" rings for my Alto Nilfisk Dynamic 4350 pressure washer? I can't seem to find any data relating to the size of the rings for the hoses and accessory wands etc


... Vacuums

DC25 telescoping handle does not seat tightly. When pulling the vac back it unseats about 2 inches. This prevents the hose from engaging securely in the base and suction is affected. Do I need to replace the clear wand release catch? I've only had the vac about a year and am surprised it would wear out so quickly.


... Dyson DC25 Vacuum

We replaced the short hose that connects the sucking part to the hole where the dirt goes underneath my Dyson DC07 but now the side of the hose that needs to attach to the machine falls off.


I know the hose you are talking about it is called the DC07 internal hose. Over time the ends can stretch and perish which will mean y ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Hello, I have a Hoover quadraflex Powermatic central vacuum system Model # s8099-031 that requires a new replacement 35 ft hose...I have contacted Hoover and they do not know where to buy a replacement hose for this model. I live in Canada. Any idea where I can get a replacement hose for this system? Thanks kindly, Tammy


Tammy, no info re your location, so I''l try this.Your Hoover hose is shot because it was made of rubber.There are new swivel handled, tangle proof lighter hoses made of vinyl which will last much longer and can be adapted to the old Hoover hea ... Vacuums

Fantom vpw46h,house pressure washer.the motor runs,it was setting for sometime started,using it,but never had any pressure besides the house hose pressure, with the motor running,then the pressure startes to work great,while using it the wand hose came out of the pressure washer,i put it back in,now the motor will only run when i try to adjust the wand head but will not produce any pressure and will shut the motor off,it seem like as soon as the wand hose came out of the presure washer and after


... Vacuums

I am replacing the hose on my kenmore canister 11622612200. i easily replaced the handle end of the hose, but cannot see how to replace the end that goes into the canister. can you tell me how to disassemble the canister end for the new hose? many thanks!


Open the canister and locate the hose intack. There is a plastic retainer which slides over the end of hose and is secured to the body of the canister with a few screws. Remove the screws and pull the retaining ring up to release the hos ... Vacuums

My bissell proheat upright steam cleaner is spraying out through the attachments just fine, but will not spray to the floor when using upright. we've taken it apart to find that there is no water at all going through one of the hoses, but it appears the hose is connected behind the on/off and heat switches, we can't seem to figure out how to get in there to replace that hose....any suggestions on how to access this?? just curious how you would get in to replace the hose, we know it is the hose..


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Hose Problem The hose broke just above the cuff on the inlet end of the hose.  I found that the hose doesn't thread into this cuff but appears to be heat bonded in some way. Can I get a replacement cuff or do I have to replace the hose?


Looks like you can just get the hose, part #38479-4, It should just screw into the adapter or it may be glued in. ... Eureka Sanitaire SC4570 Bagged Upright Vacuum

How to replace the vacuum cleaner hose


... Vacuums

The hose with wires still attached has disconnected from the wand inside. How do you reattach the hose to the dc22 telescopic wand?


... Dyson DC22 Motorhead Canister Vacuum Bagless Cyclonic Vacuum

Replaced internal pump. Color coded hoses for replacement. Marker has worn off hoses. Need proper routing of hoses from clean water tank, to heater to spray nozzles. An internal schematic of hose routing is preferred.


Hi\015\012\015\012Thanks for using FixYa. Please remove the top cover of your Bissell cleaner. Now place the Auto-Mix selector knob to the water only position. Turn the cover over. You will notice an angle on the ... Vacuums

Small fire at the hose and wand connection of beam serenity plus


... Beam Industries 2775 Serenity Plus Central System Vacuum

My mother purchased a replacement hose assembly for a Bissell ProHeat 2X and the part was shipped without any instructions... While I am pretty handy, my issue is with the supply tube, and I cant figure out how to accomplish the replacement, and as its not MY vacuum, Im hesitant to start taking things apart.I just need instructions to replace the entire hose assembly.


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

The power brush floor rug attachment on my Eureka 6997 A Oxygen Canister Vacuum goes on an off as I use it. I replaced the The power cord from the handle has 2 plug in connections: 1 at the handle / upper wand 1 at the lower wand top of the power brush attachment I replaced the entire wand assembly and it worked great for a year or so and now it's doing the same thing again. I was told to keep the power switch on the handle set to off when connecting the power brush attachment or it will bu


This is from the prongs not making a good connection causing an arch inside the plugg causing what looks like rust on the plugg. I would try snugging up the connection by squeezing the female section to get a better connection on the prongs when it i ... Vacuums

Hi there my dyson suffers from a lack of suction with of without the hose attached. we had our local repair man look at it and he replaced a hose in the head of the machine.i have replaced all the filters and ideas?


What about doing this:\015\012\015\012http://www.fixya.com/support/t2936439-dyson_suffers_from_lack_suction ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Suction Hose The suction hose has cracked so the suction feature no longer works. I would like to replace it, but cannot find that it is a replaceable part. Hopefully someone else has a solution.


Go to0 http://www.thehooverstore.com/h3000.html there also is a parts break down. You can email them at ... Hoover Floormate H3000 Upright Wet/Dry Vacuum

For a 9300 Bissell cleaner, how do you replace the flex hose? The outer part detaches easily, but the inner hose does not. How do you remove and replace it?


Here is the Instruction or User Manual for the 8920, 9200, 9300, 9400, series machinesHere is a ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

This is embarassing, but I have just looked at the Dyson DC07 manual and at my Dyson for about 20 minutes, and I can't for the life of me find the wand release button on my actual Dyson.....the manual pictures don't look like the parts on my Dyson....I don't have a hose with a wand release button....the hose just goes straight up inside the handle....Can someone help me? Thanks :)


Hi the wand release button is located directly above the the Cylinder release button. The wand release button looks like the picture below. In order to releease the wand you must firstly make sure the Electrical cable is not wrapped up for storage. S ... Dyson DC07 Bagless Upright Cyclonic Vacuum

On my DC17, the wand is not working right. The upright part works fine, but when I go to use the wand, the hose sucks in on itself. I get suction for a few seconds, then the hose collapses in on itself and no more suction.


... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0548 seconds