Having problems with your Hoover Telios Canister Vac Vacuum ?
To clean the motor I need to unscrew the hoover telios 1400
Repair Help & Product Troubleshooting for Hoover Telios Canister Vac Vacuum
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
To clean the motor I need to unscrew the hoover telios 1400
... Hoover Telios Canister Vac Vacuum
Vorwerk ET 340 - been great but now noticing strong burning smell after vacuuming some hair from the bathroom. Bag is nearly empty. Gave it a rest then unscrewed the cover housing the motor and all looks clean (dust is sucked up the pipe and doesn't appear to get near the motor). When I restarted it, burning smell still there. Are there any filters that might need changing? What could be causing the smell? Could the hair have gotten caught somewhere? Thanks.
Jessica,\015\012\015\012Try changing the dirt bag.\015\012Check if the motor gets hot after operation. You can come to check it by touching outside the motor housing. If it is hot or just warm.\015\012Is the smell of burning hair or something e ... Vacuums
I have a Hoover SteamVac Carpet Cleaner with Clean Surge. I lent it to my mother who used it without the brush attached underneath. Now it doesn?t **** up water and the brushes don?t turn. Any idea what would?ve broken? Is there a belt that would have burned out? The motor? Anthing I could fix myself, or would I need service for this?
If you go to this URL:\015\012\015\012http://www.vacpartswarehouse.com/Hoover-F7452-s/811.htm\015\012\015\012you will an exploded view of your Hoover. By going down the pictures you will be able to see the internal parts of the unit and ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum
Hoover Max Extract LS F6056900 Hand Tool not working / Cleaning Solution I need to know what I need to get in order to have the hand tool work on this model. Also, what cleaning solution is best for pet stains? Tried cleaning, pre-treating with Spot Shot and towel and/or scrub brush, then cleaning, still doesn't work. PLEASE HELP!!
My vax power 8, 2200 watts 300 air watts 4L capacity upright Hoover is brand new, I emptied out the dust/dirt collecter and cleaned the motor filter yesterday for the first time, i switched it on and all fine, the brush is spinning and the hose is sucking, put the Hoover to work it's fine for about 30 seconds then then suction stops and its dead it won't collect no more, so switched off taken apart again and the motor filter is blocked and full of dust, so I unblocked it, do the same process aga
I had the same problem. It looks like the seal on the lid on the bottom of the cylinder has fallen out when it was emptied. There is no longer a proper vacuum being created so you don't get the cyclone effect and the dirt doesn't collect where its su ... Vacuums
Hoover wiring the blue wire that is in the lead that runs from the hoover to the plug that goes in the wall has come loose at the hoover end and has come out of the actual hoover. i've unscrewed it but am unsure as to where the blue lead (bare copper) needs to be screwed... if you see what i mean?!!
Hello lukeplayer,\015\012Based on your description, ( first disconnect the plug from the wall recptacle).You will need to open up the Hoover Vacuum Body to gaion access to the internal wiring. In order to better assist you, please provide me wi ... Hoover Vacuums
Hoover Jet and Wash 1500w S6254 001. Used once with great difficulty as assembly and use instructions are hard to follow.Now will not work as carpet shampooer at all, although assembly is correct as far as I can see and both motor and pump appear to be working and I am using the recommended cleaning fluid.Hoover website is no use at all in solving the problem.No cleaning fluid is being drawn up from the tank in to the cleaning fluid hose.There is suction from the suction hose so the problem appe
I am having the same prob my uncle got me one i cant find the manual anywhere to set it up the prob i have is where does the handle to make the water go out connect tooo ??? on the main pipe that sucks it back up i have tried every which way but not ... Vacuums
I have a Hoover SteamVac SpinScrub with Clean Surge Carpet Cleaner. I loaned the cleaner to my son, who lives 3 hours away from me. My son returned the Steam Cleaner to me on Easter Sunday. My son failed to return the Owner's Manual. I need to clean my ottoman. I have never used the upholstery & stair cleaning tool. Would you be able to e-mail me the instructions for this chore? My e-mail address is: [email protected] My name is Kay. Thank you!
Hi,I would be glad to send that. But, you never Mention the Model Number and there are Various Models introduced by Hoover.Let me know the Manual and within Few Minutes, i would be able to send you one more email which would h ... Vacuums
I cleaned out my dyson ball as it smelt when i hoovered, cleaned filters, washed out canister and took the screws out of the front bar so i could clean near the brushes.. now its making a high pitched noise and when i switch it off it makes a noise like an engine shutting down! Have i disturbed the motor?
Hi its Darran at Dyson. The screws on the base of the cleaner head should not have to be removed to access the brush bar so it is possible that the brush bar has come out of alignment, hence the noise the machnie is making. Pl ... Dyson Ball DC24 Bagless Upright Vacuum
Need to get to the motor to clean it and cannot get the cover off
... Eureka 6984A Bagged Canister Vacuum
Need new motor for "WAP ST20" hoover
... Wap 28538 Wet/Dry Vacuum
My A 2045 Karcher vacuum's suction is really weak and the motor seems to be working VERY hard. The motor sounds like it used to when the vacuum fell over and went into overdrive! Now it's in overdrive all the time and the suction is minimal. Nothing is blocked and the filter is clean and dry. What do I need to do?
... Karcher K DS 5500 Vacuum
The motorized wand attachment keeps shutting down after 10 to 15 seconds after pushing the red reset button. I've thoroughly cleaned dirt/debris from around motor. Do I need a new reset switch? Thanks, Tom
Either the reset is bad or the motor is drawing too many amps and tripping the reset. Do you have an amp meter? Check the amps being pulled by the wand attatchment against the load recommended by the manufature, this is usually located on a plate som ... Rainbow E series Canister Wet/Dry Vacuum
Took my Hoover Steam Vac apart to clean it and now it won't **** up the water but was working fine before I got the bright idea to clean it. Took four screws out but did not touch the motor. It puts out water and the brushes rotate but no suction? Thank you for your help, Cathy
The suction is created by the motor and is pulled to the motor through the flexible hose. The hose could have pulled off at one end or it could have torn in a spot where there is more pull on the hose like when you lay the handle down to empty dirty ... Hoover F7431-900 SteamVac Vacuum
Shark infinity vacuum nv31c motor overheats. everything is clean and free of clogs. it will work for 3-4 minutes, then shut off. does the motor need replacing?
Mine takes longer to shut down, but I just started having this same problem. I wish I knew what's causing it so I could fix it. I think maybe we had a power surge at some point when I was using it last week. :( ... Euro-Pro NV30 Infinity Bagless Upright Cyclonic Vacuum
No motor when switched on two red lights flash,cleaned hoover, put back together motor started,then cut out after a few seconds
I would double check your wiring, Make sure all wiring is tight. No cracks, no pinched wires. If needed, bypass the switch and see if it will stay running. If so, switch would be bad. If it's the same, then you have a wiring problem or a worn motor a ... Sebo Automatic X1 Bagged Upright Vacuum
I forgot to replace the vacuum cleaning bag in my Hoover Wind Tunnel Supreme Mach 3.3! It overheated and turned off. I spent all afternoon cleaning the dirt out of the inside, filters, etc. It still overheats when used over 1 minute. Do I need to buy a new vacuum?
Hoover fh50020, cleaning solution leaking. loose white hose near the motor, can't find where it connects. think it must have something to do with the cleaning fluid not spraying out properly.
... Hoover F5906-900 Upright Steam Vacuum
My older Dyson DC14 (the purple one) early model with a clutch on the beater bar belt needs a clutch replacement. The bar has been cleaned and there are no worn or damaged parts so I conclude that the clutch at the motor end of the belt needs to be replaced. I can find the part online but no instructions on how to disassemble the vacuum to get to and replace it. Dysons only advice is to give me the address and phone of the nearest service center. Can you help me?
Have a look at www.dysonmedic.com which has some very useful info on dismantling and repairing Dysons.\015\012\015\012Although this site doesnt actually cover the DC1 ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum
I have a Hoover steam vac Model #F5865-900. I am unable to have the cleaning mode change from tools to floor when lowering the handle release. I hear a click, but the indicator stays on tool. I need to know how to get to the assembly that controls the cleaning mode.
... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum
I have a NUTONE central vac, when I turn on the power, It sounds like its grinding glass and doesnt suction. Could it be that broken glass got caught in the motor and all I need to do is clean it, or is this the sound of a failed motor?
More likely it's something in the fan. However, I suggest taking it to a vacuum repair shop to make sure. Something could have got into the fan system and is making a racket, but the motor itself won't crunch up glass. ... Electrolux Central Vacuum
I have a vax cylinder model V-094. Working fine then started to play up. Switch it on and the motor seems to struggle to power up. Kind of wurrs up and down. Was thinking it could be the brushes have worn. Tokk to bits and cleaned her up, took a look at motot and brushes, cleaned them too, back together and still them same problem. Help please, hoover is not old but has done some work really don't want to through away something that can be fixed.
Hi.\015\012\015\012after all you have done I would be pretty confident its the motor thats faulty they are expensive to buy so machine is going to be scrap,\015\012\015\012Sorry.\015\012\015\012 ... Vacuums
HI, my motorized brush barely turns.It makes a hot rubber smell. I took apart and noticed the spindle the belt turns on discolored from heat. Cleaned it, but still no turning of the brush.The vac is a hoover wind tunnel. As it moved accidentally touched the belt/ spindle and burned my hand a little. Very hot in area. Bright spark from motor noted. Was careful not to touch that part!
That means that the belt is stretched and it is slipping on the motor shaft, that is why it is hot and smells like burning rubber. You need to replace the belt. Here is the correct belt you need: ... Hoover S3765-040 WindTunnel Bagless Canister Vacuum
Needs new motor have the part but cannot get into the part of the hoover where the motor goes
Have a look at www.dysonmedic.com. ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
Hoover F5809 Hello, I seen a few of your post and was hoping you could help me. I just became a member today. My sister gave me her old Hoover Steam Vac-Model F5809. This thing is so dirty and clogged because my sister has pets. So far I've gotten it all taken apart to clean it. I'm not a newbie and taking apart and fixing things. I have fixed things like microwaves, washers, dryers, dishwashers (still learning about TV's-very hard, hehe). Anyway, I got what I believe to be the motor cover off.
That cover is the called the fan cover and is usually pressed on. Tapping on the edge with a flat blade, you may be able to get it off and hope you don't bend it up, you will to put it back on tight enough so it will stay in place. Another thing to ... Vacuums