Having problems with your Hoover Tempo Widepath Upright Vacuum - Blue ?

Self propel feature broke on Hoover Tempo Widepath

\015 I was vacuuming and sucked up a tie which just wrapped itself around the brush; after I released it, the self propel feature was non existent and the vac itself didn't seem pick up as well at all. I recently changed the bag,so I know that's not the problem. Please help!\015

Answers :

Sounds like the tie has loosened the belt off. You may have to check under neath the sole plate by removing screws and having a look. If the belt is broken it will have to be replaced. If its not broken check that it hasn't moved within the gear assembly of the self propel mechanism. Fit everything back together and it should work after that. 
Repair Help & Product Troubleshooting for Hoover Tempo Widepath Upright Vacuum - Blue

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Self propel feature broke on Hoover Tempo Widepath


Sounds like the tie has loosened the belt off. You may have to check under neath the sole plate by removing screws and having a look. If the belt is broken it will have to be replaced. If its not broken check that it hasn't moved within the gear asse ... Hoover Tempo Widepath Upright Vacuum - Blue

I have 2 Hoover Wind Tunnel-self propelled bagged vacuums-U6433-900 model.The roller bar does not agitate, the self propelled feature does not work and, in general, the vacuum is not performing well. I have replaced the roller bar, the v belt and the wide belt. The filters have been replaced and it has a new bag. I have had both of these since 2004 and they were fairly expensive $200 each) but if the repairs are prohibitive, I might as well get new vacuums. Suggestions? I just spent $100 for bel


The Hoover WindTunnel self propelled is a machine that we see in our retail stores (Vacuums Unlimited) constantly. The benefit of having a supposed "self-propelled" machine wears of quickly after the numerous time you will need to take this machine ... Hoover Vacuums

Just replaced the belts on my Hoover Windtunnel II self-propelled vacuum. The brushes are now turning ok, but the self propelled feature is not working. Squeals when when you lock it in the upright position.


Check the plastic part, which the the self propelled cable is attached to. (release the handle, tilt it back. You should be able to see the cable attached by a screw to a black plastic arm.) It is either broken or the cable is lose. ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

Hoover Bagless Windtunnel - Self Propel feature not working


I have the same problem with ours. If you lift the vacuum by the handle it breaks the lever on the transmission. You can find a replacement cable and lever on line for about $16.00 it is somewhat involved to repair but can be done by someone with mec ... Hoover Vacuums

Is there any way to repair or replace the belt GUIDE on the inside of the belt compartment of a '97 Hoover Wind Tunnel (not self-propelled)? It became twisted when a belt broke and now the belt rubs against it and sounds really weird, and I'm sure new belts will continue to break.. This guide is a long piece of molded material (part of the compartent wall) to keep the belt from coming off the pulley. It also had a sort of metal clip on it. It was loose and I took it off because of the way the pa


Honestly you should take it to a vac.shop they can fix any vac. ... Windsor SR12 Sensor Bagged Upright Vacuum

Hoover vac 6432-900 reverse cable broke this model # is correct about 12 years old wind tunnel bagged self propelled


The quick and easy here is to just splice the cable and tape it. If you just cut the insulation back to get to the wire and get a couple 'barrel connector' at the hardware store. These are crimp style connectors and you need a small crimper to put th ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

I have a Dirt Devil Vision self-propelled vacuum cleaner. Recently, the self-propelled feature is stuck in the backward mode, so it only goes backwards! I can get it to go forward if I push really hard (i guess it is good for a workout!). I try to turn off the propel feature completely, but it will not turn off. please help!


Hi, the problem you are having is going to be with the switch that controls the forwards and backwards settings so with this stuck in backwards their is no way you can get this turned off, the other problem is your not going to be able to replace thi ... Dirt Devil Vision Turbo W/Bonus Upright Vacuum Vacuum

Hoover 6485-900 self propelled will not roll. Self propel switch seems flimsy and I can't tell if it's working. New vac used about five times. I can see a wire moving down near the rollers when I engage the self propel but the wheels don't turn. Thanks for any assistance you can provide.


... Vacuums

Hoover Tempo Widepath - propellor not working


If you are refering to the roller underneath, the belt nees to be replaced. Simply remove 4 bottom screws and then the roller, Place new belt on roller and thenon motor shaft, pull belt with the roller to install in position and install bottom plate. ... Hoover Tempo Widepath Upright Vacuum - Blue

Hoover WindTunnel Self Propelled Handle Release Lever broken


... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Hoover Upright Bagless WindTunnel does not self propel (U6625-900). Belts are new, Brush turns strongly. Wheels propel forward very weakly and do not reverse when the handle is pulled backward. Is there a mechanical link from the self propel switch to the "transmission" ? Are there any gears that could be worn or not engaging properly?


... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

Hoover self propelled upright


You can adjust the cable, it is from the front, on the right side, it has a torz screw that you loosen, then you can slide the cable back and forth, just move it alittle back then tighten it down and try it. Here is a site that you can see a bigger ... Hoover U6616-900 WindTunnel Bagless Upright Vacuum

HOW DO I REPLACE THE DRIVE BELT ON A HOOVER WIND TUNNEL SELF PROPELLED


Take the brush belt and slip it over the pull into the groove. Then take the flat belt and hook onto the motor shaft and then pull belt over pull and push it around the entire pulley. It can be difficult but after the first time it is easy. You ha ... Hoover Company Wind Tunnel U53019 Upright Vacuum

Replace power cord for hoover tempo sweeper - Hoover Tempo Widepath Upright Vacuum - Blue


... Hoover Tempo Widepath Upright Vacuum - Blue

Hoover upright self-propelled drive vacuum cleaner u6331-93 will not self-propel


Here is a video how to fix ... Vacuums

Hoover U6637-960 the self propel is not not working. When lowering the handle it acts like it would like to work but the roller will not turn. appears to be something to do with the self propel part of the handle . took the screws aout but can not get it apart. Is there another belt of something in there?


This vac has 2 belts. If both self propel and roller not spinning then most likely it is the wide flat belt broken or off. 4 screws on the bottom should gain you access to the belt area. another issue for this model series is a worn pulley on the rol ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

Self-propelled Hoover windtunnel (with bags) will not self-propel. Belts are all in order, but I am quite sure it has to do with the cable. How would I fix this and how does the end of the cable with a nut, connect?


This might help - go to following website and look for "troubleshooting" \015\012http://www.fixya.com/support/p40544-hoo ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Hoover self-propelled self-propel not working. belts ok.


No suction on Windtunnel 6630-900. All belts work, brush turns, it just won't pick up anything. ... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

Self propell doesn't work. Motor spins and belt burns, brushes do not turn. model Hoover self propelled u6425-900


May be a stripped sprocket/cog or snapped shaft. check and replace as needed. ... Hoover Vacuums

Hoover self-propelled wind tunnel doesn't self propel going backwards.


Your self propel cable sounds like you need to have an adjustment. reccomend a service shop repair. ... Hoover Vacuums

I have a Hoover power max self propelled vacuum. The belt that goes to the self propelled part keeps slipping off. I've had the belt replaced, but the problem persists. What can be wrong? I've taken it to a Sew N Vac repair, but all he did was replace the belt again. And it still has the same problem.


I can guess of one problembelt gets removed when motor is running right?am assuming that belt is fit tightly and fits correctly when motor is in restif so then ur motor is not running at a proper speed which can be a pos ... Vacuums

Hoover tempo plus attached tools manuel - Hoover Tempo Widepath Upright Vacuum - Blue


... Hoover Tempo Widepath Upright Vacuum - Blue

Upright hoover U6617-960 will not self propell


... Hoover U6616-900 WindTunnel Bagless Upright Vacuum

Self propelled feature does not work. I replaced


There is a cable from the handle down to the transmission on this machine that breaks all the time or the cable is mounted to a plastic piece that is broken. That will need to be replaced. ... Hoover U6476-910 WindTunnel Upright Vacuum Cleaner Bagged Vacuum

V-belt flapping on Hoover Self-Propelled WindTunnel Bagged Vacuum


... Hoover U6441-940 WindTunnel Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0491 seconds