Having problems with your Hoover Tempo Widepath Upright Vacuum - Blue ?

The roller turns strong and the belt is new,but the dirt accu-mulates and doesnt get sucked up! there no observable clogs and the filter side vent blows strong.......ive removed beater,belt and am assuming there may be a problem inside the motor housing as all else appears normal..i was an aviation mech in the military and the above is my assessment........

Answers :

Are you sure you have the belt on correctly?\015\012If it is not, the beater brush will push the dirt, etc, in front of itself and not back to the suction port.
Repair Help & Product Troubleshooting for Hoover Tempo Widepath Upright Vacuum - Blue

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

The roller turns strong and the belt is new,but the dirt accu-mulates and doesnt get sucked up! there no observable clogs and the filter side vent blows strong.......ive removed beater,belt and am assuming there may be a problem inside the motor housing as all else appears normal..i was an aviation mech in the military and the above is my assessment........

Are you sure you have the belt on correctly?\015\012If it is not, the beater brush will push the dirt, etc, in front of itself and not back to the suction port. ... Hoover Tempo Widepath Upright Vacuum - Blue

Vorwerk VK121 vacuum cleaner - smell of burning from housing enclosing motor. How do I get into the housing to inspect the motor? After tilting the bag sideways, there are two screws holding the housing visible, but there seems to be a thrid fixing inside the point where the handle shaft is attached - is the handle simply clipped in place? Thanks

Yes the handle is clipped in place and should come out when the button in front is pushed. Remove the screws you wrote about. After that the puzzle begins. At the bottom of the vacuum where the head is attached, remove the head by pressing the but ... Vacuums

My electrolux ambassador power wand quit working. I replaced the switch that shuts it off when the roller stops, but it wasn't the problem. The on/off switch is fine, the motor is fine. We have traced the problem to the wires inside the canister by opening the inside cover to the bag container. We see the power cords going into the canister but we're not able to get to anything. We can't find any screws to undo that would open it up in order to follow the wires deep into the canister. We've bypa

... Electrolux Vacuums

Hi I need help because I have a problem with my Electrolux Centralux Central Vac system in my house. When I plug the vac hose in the central vac socket at first I heard the motor running very gently with NO suction then after a minute or so it went completely dead and they is NO motor sound, suction, or anything happening what so ever. Can anyone tell me what this problem is???

Have you checked for a clog in the lines or in the hose? If there is no clog in the system anywhere, then your motor could be dying. ... Electrolux Centralux Vacuum

Miele S5000 (revolution 5000) vacuum cleaner - How do I open the casing? When the power button on the handle is pressed the green power-level lights on the handle light, but the motor sounds like it gives a little 'jump' but nothing more. The orange power light on the body also dims. I assume the motor or fan is jammed, but I can't open the body to find out. I've taken out to screws inside near either end of the handle, but to no apparent effect. I'm assuming the body is held together by plastic

... Vacuums

Motor problem When i plug my steam vac in the motor sparks and smokes. It smells as if the motor is burning out. I've tried different outlets through out the house and get the same outcome, what can i do to solve this?

Nothing you can do im affraid its the motor armature so unless it can be stripped down then you will need to replace the motor i would get a price for the motor to decide if it is worth doin sorry. ... Vacuums

Recently my central vac system started making a louder than usual and laboured sound when in uise, enough so that I took note and inspected the canister and motor while running. The motor was trowing off blue sparks and looked like it could 'POP' at any moment. I will not risk using it until I know what the problem is and how to repair it. My assumption is the motor needs to be replaced. The system came with the resale house I bought 3 yrs ago but I do not know the age of the system itself.

... Vacuums

Hoover EmPower 4600 keeps blowing circuit breaker. The number of outlets in the house that will allow me to run the vacuum is dropping quickly. It is a 4 year old house and all the circuit breakers are 20 amps. The vacuum only has a 12 amp motor. I am at a loss to solve this problem.

Take it to a friends house and plug it in if it does the same thing then the problem is in the vacuum cleaner.check your cord and see if there are anny cuts in it.you can open the breaker box then plug in the vacuum and watch the breaker box.you migh ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Hi I’ve got a Panasonic vacuum cleaner MC E468 1600W a few years old now but works well up to recent problem. Not picking up I checked the obvious things and found excessive air being sucked in around the hose housing at the back of the vacuum (as it enters the waste bag) On inspection it appears to me as if there should be some sort of gasket that may have perished and been sucked in, however I can’t identify any such part. Any thoughts on what the problem/solution may be will be appreciate

The hose on the back might be loose - check to see that the hose is not obstructing anything where it screws in at the back - or indeed the screws may be loose themselves; some of the MCE 468 models had an additional ring washer that sits between the ... Panasonic Vacuums

Windtunnel Hello: I was reading thru another readers problem of power to vacuum but won't turn on. Same problem for me. All hoses are free of clogs and I have the vacuum basically taken apart as far as I can. You state a THERMO by the motor may be open. What does this part look like? Thank you. Craig

The thermo is a small square piece with two wires coming out of it. Did you check the switch? The switch has a high failure rate. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Replacement parts... I've got a 3594 Bissell and the belt has come completely off. In the process of breaking, it bent the metal guide inside the motor housing and melted the plastic that holds the guide and keeps the belt inline with the roller. I've got it running again by using a screw I filed all the threads off of, but it only works for 10 minutes at a time before breaking another belt. This process is getting expensive, as it usually takes 30 minutes to completely vacuum the house. Is ther

Most likely it is the top cover that needs to be replaced, part #2031238 and is around $30. It would have that guide on it. ... Bissell 3594 CleanView PowerTrak Bagless Upright Vacuum

Again, I have a Bissel Model 3760-4. The same problem as everyone else. The beater bar will not turn. Took apart, nothing. Took to vacuum repair shop and they said it is not getting power to the motor to the beater bar. Seems like a fair number of folks are having this same issue. You would think Bissell would come up with a fix, if nothing else to save their reputation. Thanks Diane

... Bissell 37604 Lift-Off Pet Bagless Upright / Canister Vacuum CleanerVacuum

I have a similar problem as many do with this model, "clean Roomba's brushes".. We took it apart last night, cleaned out all of the dust we saw. we removed the cover, the housing for the brushes and everything else we could. Still has the same problem. What now?

Mine did the same thing and no mater how much I cleaned the brush or pulled fibers of the ends it did not stop until I:Removed the little yellow tabs on the ends of both brushes and used a tooth pic to remove the built up inside the bearing ass ... iRobot Roomba 530 Robotic Vacuum

Hi., If anyone could help it would be greatly appreciated, I have a Flair 3055 ventalation system in my house and over the last five years two fan motors have gone bad. it has been mickey moused together by a local repair man, and as of last week, it has died again. At 4-5 hundred a pop I would like to fix it myself, can anyone suggest a good replacement motor that will fit and work. My honey has breading problems and at this time of year, every penny is allocated, so time is of the essence. t

Hello George, Sorry about your predicament. Various fans are available for your unit but since you say the unit has been mickey moused together adjustments must have been made to the fan seating and system therefore if you order any particular fan th ... Vacuums

How to open the motor housing.

Pls i want put music in my phone but its not possible i need ur help ... VAX Appliances 2000 Canister Vacuum

Roomba 530 clicks steadily as it moves, and has a limp, so something is catching inside it - inspection suggests not the brushes, not the wheels, so maybe the electric motor? Any ideas as to problem or where I can repair? Thanks. Bill

Symptoms suggest the clicking is coming from the wheel switch, and it must be disassembled and cleaned. ... iRobot Roomba 530 Robotic Vacuum

Dyson Animal motor is running, beater bar is turning but very little if any suction. No suction from hose either. The inside canister is filling and moving, so there is some dirt being sucked in there. I have thoroughly cleaned all filters but not sure what is causing the problem. Any ideas?

Obstruction in the hose?\015\012Your vac has developed a hairball possibly.... when a piece of flexible media ie.... cardboard, plastic etc... gets lodged in the hose, and begins collecting hair & dust to the point it no longer has enough d ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

I bought a house that has a 1970s GE microwave oven that's built-in above a traditional oven. (Unfortunately, I can't locate a model number for the microwave.) I'd appreciate having information about the "food temp control," which is on the front of the oven. There is a wire probe that goes from the inside of the microwave to the food. I assume that relates to the "food temp control." I'd appreciate having any information about how to use the "food temp control." Also, I 'd like to know wh

I serious doubt that probe would work any longer for they go out in ten tears or less ... Vacuums

I have power going to the fan above the motor section and into the sensor control for the remote but not at the other end of the sensor which is located inside the light kit housing

The unit that holds the bulb may be burned out or a loose connection. ... Vacuums

One day I was vacuuming and it sounded like something went up inside somewhere and the motor, I assume,..... is frozen ..all it does is hum when I turn it on! I have changed the belt, filter and checked and cleaned all hoses... what could this be? THANK YOU, Gail

It's likely something got into the fan, is stuck there, is preventing the fan from turning, and so prevents the motor running. There's a good possibility the motor burned out because of this. If there's a strong smell of burning metal, this is prob ... Hoover Elite Rewind Bagless Upright VacuumVacuum

Belt drive Not only do I need a PN for the drive belt on the Panasonic MC-V7395 Vacuum Cleaner, I've noticed that there are problems with the belt breaking. Can someone also explain the proper way to install the belt over and around the motor spindles and any other information that may help. Thank you.

Http://www.partstore.com/Model/Matsushita/Panasonic/MCV7395.aspx?SearchTerm=True ... Panasonic MC-V7395 Vacuum

FAN PROBLEM??? good morning! my vacuum smells like burnt rubber (fan perhaps) but I can't find how to get into main part of the vacuum. it's just very rounded with no latches or screws to get inside where the motor, belts and fans would be located. can you help me? thank you

There isn't any belts, and the fan wouldn't be rubber, so not sure what you are smelling. Maybe this picture will help you.\015\012\015\012 ... Bissell 6700 Butler Revolution Bagged Canister Vacuum

Hi guys, I have a bissell 9400 2x proheat with a fault. When you turn on the machine it trips the RCD in my house and makes a poping noise, i am a little technical so i had a look inside. The pcb under the handle was damaged with burn marks i unpluged this and tried again and the machine powered up, don't think the rollers moved though. What do i need to change roller motor,pcb?? Help please!! Regards Russ

I've seen the same problem in one of these we had in for repair. The pcb in the handle is involved with controlling the roller motor. The problem is with the motor. In my view, this machine is a triumph of design over practicality... The motor is loc ... Vacuums

When put on fused all my electrics in house. Now does not work . fuse is ok. wondering what else may have caused this. vax is only 8 months old but lost receipt.

Sounds like motor has blown - fuse in house blew quickly, before the one in the plug had time! ... Hitachi Vacuums

Kirby Heritage II Replacing the Motor in the housing HELP!

... Kirby Heritage II Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 1.7875 seconds