Having problems with your Hoover Tempo Widepath Upright Vacuum - Blue ?

Cant raise for carpet height

\015 Vacuum picks up well but wheels won't adjust for carpet height. They are stuck at the lowest and it's difficult to push on the thicker carpet.\015

Answers :

Repair Help & Product Troubleshooting for Hoover Tempo Widepath Upright Vacuum - Blue

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Cant raise for carpet height

... Hoover Tempo Widepath Upright Vacuum - Blue

On my hover U6616-900 the self propell work fine on the med setting on med height carpet, but when I go to low height carpet and height set on med the self propell does not pull the vacuum and it is hard to push. Also if I raise the height to the highest setting the self propell works correctly and appears to clen. Any ideas? S/N 090400184555, think this vacuum is maybe 5 years old and my wife uses it lots. Should I think of maybe a complete overhaul or a replacement at this time?

This is a typical problem you are describing. I would recommend you change the belts, this will resolve the "hard to push" and most likely resove your issues. based on the s/n given you maching was made on sept 2004. ... Hoover U6616-900 WindTunnel Bagless Upright Vacuum

I just installed new carpeting and the vacuum makes deep tracks ( 4 of them, corresponding to the grates on the underside). They are so deep, I am concerned it will score or even cut the carpet. There is no height adjustment so I cannot raise it. Thank you

Hi there,The tracklines left by your Dyson are caused by the revolving brushbar grooming deep into the carpet pile to dislodge trodden in dirt, grit and animal hair. However, you may want to contact your carpet manufacturer to ... Dyson DC07 Bagless Upright Cyclonic Vacuum

I cannot push the dirt devil on my carpet ai need to raise the cleaning height

... Dirt Devil Vacuums

I have a Dirt Devil M088400 - Vision Turbo Vacuum. A spring fell from the bottom and the carpet height adjust isn't working. The rollers under the unit won't stay in place either. Can you tell me how to put the carpet height adjust back together?

The roller attaches to wheels. There is a spring that attaches from roller to hight adjustment selector which is a plastic peice with a little hook on bottom that spring attaches to. Both peices should have a hook that the spring ttaches to. ... Dirt Devil Vacuums

Height adjustment The height adjustment button on my upright is nonfunctional.  The Height is set closest to the floor and it makes it difficult to move on medium height carpet.

You'll have to turn the upright to its side to show the sole plate where the rolling brush is. Check where the front wheels are located and ensure there is no blockage obstructing the rotary dial. Sometimes the spring mechanisms can work themselves l ... Electrolux Oxygen 3 Upright Vacuum Cleaner - EL5035 Vacuum

Brush Roll belt stops turning durring vacuuming on WindTunnel self-propelled, v belt is a little loose with handle down. Tensioning roll is engaged OK, but fully at the end of its travel. Replaced belts flat and v, but still stops turning even on high carpet setting when vacuuming. Carpet setting and height adjustment appears to be working OK, roll is clean and turns easily when out. Also turns easily until it engages the carpet. Self propel function works just fine.

... Hoover U6485900 Bagged Upright Vacuum

Dirt devil vacuum cleaner--trouble vacuuming dirt and pet hair on carpeting --is the problem with the spinning brush which contacts the floor,  not contacting the carpeting??  I thought (when I bought this vacuum) that the aforementioned brush was adjustable to various heights of carpeting.  Sometimes, it seems like nothing is being vacuumed up --unless I have just put a new bag on the vacuum... Do I need or can I replace the spinning brush on the bottom of the vacuum so it kicks up and vacuums

Try replacing the belt. Rubber belts stretch out after about a year. ... Dirt Devil CE6100 Featherlite Upright Vacuum

Carpet Height Adjust Broken - Spring fell out

... Dirt Devil Vision Turbo W/Bonus Upright Vacuum Vacuum

Carpet height adjustment not changing the height of the brush.

... Eureka Smartvac 4870 Bagged Upright Vacuum

How to take apart the Hoover U6437-900 to change the belt and clean it. I have the belts and I have removed several screws. It looks like the knobs for the wheel carpet height and carpet to floor selection are the problems but I can not figure out how to remove the knobs. Besides, I am not certain if this is the problem. Do you have the instructions? Thanks

HERE IS THE MANUAL > http://hoover.com/file/500/ ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Hoover windtunnel Not sure of model number- but brush roller clamps down on carpet being vacuumed and stops spinning regardless of which of the 3 height selections is selected. Can make it work by leveraging the handle down (or back towards me) to keep the cleaning head a little off of the carpet-any suggestions or ideas?

Would suggest the drive belt is stretched and thus is slipping when contact is made with the carpet. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

I need to change a belt and cant remove the casing as carpet adjust is attached and cant see how the red knob is removed

... VAX Appliances Vax X3 Bagless Upright Vacuum

My bissell proheat carpet cleaner wont dump water or solution. It will however **** up water and solution if dumped on the carpet. Help I cant clean up doggie pee and it smells in this heat!

Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 8910 ProHeat Clear View Upright Vacuum

I have the Dyson DC14 and its like it's not brushing the carpet anymore, The brush is spinning, but its like it isn't self adjusting to the carpet height? It still has suction, but doesn't make the same sound it used to when you'd start vacuuming. Its like it never adjusts anymore???

Hi its Darran at Dyson.It sounds as though the internal hose underneath the machine has twisted slightly. With the machine switched off, lay it on its side and look at the base. You should be able to see a small corrigated hose. Simply t ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Why won't the brushes turn when on the carpet? They will turn if I lift it up off carpet. I have adjusted the height and everything and they won't turn.

Your belt is stretched and therefore won't spin when its against the resistance of the carpet. You just need to replace it. You can get this belt here: ... Bissell Upright Vacuum - The Pet Hair Eraser 1 ea Vacuum

How is the V-belt tension adjusted (Hoover Model U6439-900)or how do I know if the tension is correct? There seems to be a lot of "play" in the belt and I'm wondering if that is the reason the brush roll only turns as the wheels turn, regardless of the carpet height setting. And yes, the brush roll is set for carpet, not hard floor. Or is the cause of the problem something other than the V-belt? A new flat belt was installed when the machine was professionally serviced so I assume (?) that was a

The V-Belt is not adjustable. There are two ways the belt has no tension: (1) when the handle is upright, a mechanical lever takes the drive tension off the belt, and (2) the brush roll lever setting you described. The upper handle would have to be ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

I bought the 085845 yesterday, put it together and had trouble pushing it on my 8 x10 area carpet. The vacuum did not move easily and seemed to "pick up" the carpet. It seemed that the automatice height adjustment may not have been working. Any suggestions?

I called Dirt Devil and they said return it! ... Dirt Devil Featherlite Bagless Vacuum M085845Vacuum

How do you reattach the front rollers on hoover elite rewind so that the carpet height adjustment works

... Hoover Vacuums

Carpet height selector not working on Eureka The Boss SmartVac

... Eureka Smartvac 4870 Bagged Upright Vacuum

Carpet Height Adjusment

In addition to the tab that contacts the bottom of the slider, there are 2 protusions on the adjustable wheel plate that move through holes in the housing, but only when the handle is tilted to begin vacuuming. The wheel plate has a spring that ... Hoover U5753-900 WindTunnel Bagless Upright Vacuum

Carpet height selector doesn't work.

You have a bad belt. It may not be broke but it's so loose that it isn't turning the brush roller when a little resistance is applied to it. That belt is cheap and it's routine maintenance to change it about every 6 months. ... Vacuums

Cant get hand tool to work on bisell lift off carpet cleaner

... Bissell Lift-Off Pet Deep Cleaner

Cant get it to spry solution on to carpet hose pluged if so how d

It is because the pump belt is worn or stretched. Here is the replacement you need:Bissell Proheat Pump Belt ... Bissell PowerSteamer Deep Cleaner Plum Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0359 seconds