Having problems with your Hoover Tempo Widepath Upright Vacuum - Blue ?

The level to adjust the pile height has become detached. How do I remove the blue cover to reattach it?


Answers :

Repair Help & Product Troubleshooting for Hoover Tempo Widepath Upright Vacuum - Blue

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

The level to adjust the pile height has become detached. How do I remove the blue cover to reattach it?


... Hoover Tempo Widepath Upright Vacuum - Blue

U6446-900 the drive cable came off and I need to remove the top cover so I can reattach the cable but I can figure out how to remove the cover


From the underside:\015\0121. remove 4 screws holding agitator cover in place\015\0122. remove 2 screws (black screws) holding hose retainer in place, pull hose out through top\015\0123. remove three screws, 2 long, 1 short holding top cover: short ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

Trying to attatch the wires from the light kit to the fan but the blue and white wires from the fan have white caps on them covering the wire. Do these need to be removed in order to attach the wires with the wire nuts? If so, how are these white plastic caps removed?


They're called "wire nuts". Turn them counterclockwise to remove, lay the wires you need to join side by side with the ends of the bared sections even and screw the nut on. lp ... Vacuums

How do you dismantle a Panasonic MC-3920 vacuum cleaner? I have removed the 4 screws at the top but still doesn't come apart and one got ideas. How do you remove the blue top cover ?


... Panasonic MC-3900 Bagged Canister Vacuum

How do you reattach the front rollers on hoover elite rewind so that the carpet height adjustment works


... Hoover Vacuums

Removing the cover from U6445-900


Take off the bottom plate, then there 2 screws on each side(from the bottom)Take the cover for the hose, There is a catch on each side from the bottom edge, use a flat blade and push in, the top will release. The actuator arm just has that e-clip h ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Dirt devil breeze with automatic height adjustment has become hard to push on carpet. How do I fix that?


... Dirt Devil M082550 Breeze Bagless Canister Vacuum

I have a Sears Upright vacuum cleaner, model 116.35922500. The vacuum wasn't picking up. I discovered a clog in the nozzle hose. I attempted to remove the cover of the brush unit to clear the clog. I was unable to remove the cover completely, but was able to clear the clog. My problem now is that I cannot replace the cover correctly. Is there a way to remove this cover? Thanks, Elizabeth


When you tried to remove the cover did you have to put a little force on it to get to the clog ... Vacuums

Agitator belt failed in my Hoover F5853-900 Steam Vacuum Cleaner. But can not remove bottom Cover .. have removed top cover and two screws from the bottom Cover. The smaller Cover is glued to the large Bottom Cover. Need help.


Hello,Unscrew the plate. check if there is any screws at the bottom, if none, exact little pressure to pull out the bottom cover. At this \015\012point you should be able to see the broken drive belt along with the two\015\012 drive bars ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

Flair S2220 Removed the four screws holding bottom cover but still unable to remove cover. Is there something else holding cover? The cover on the srew end will seperate but something appears to be holding cover on beater bar end.


Pop out the two little rollers underneath, at the front. you will find two little screws holding it on. Unfortunately, I found after I broke it off! ... Hoover S2220 Flair Bagless Upright Vacuum

Replacing the height adjustment on bissell cleanview model 3576


... Bissell 3576 CleanView II Bagless Upright Vacuum

Height adjustment The height adjustment button on my upright is nonfunctional.  The Height is set closest to the floor and it makes it difficult to move on medium height carpet.


You'll have to turn the upright to its side to show the sole plate where the rolling brush is. Check where the front wheels are located and ensure there is no blockage obstructing the rotary dial. Sometimes the spring mechanisms can work themselves l ... Electrolux Oxygen 3 Upright Vacuum Cleaner - EL5035 Vacuum

I havea Bissell ProHeat Model 7901. My problem is that the brush doesn't rotate. I have removed the access cover and both belts and found that the central cylinder for both belts is frozen and will not turn easily. Both belts are fine, except they are now burnt from this cylinder not being able to rotate. What I need is how do I remove the top cover to get at this cylinder to remove it and free it up?


... Bissell 8910 ProHeat Clear View Upright Vacuum

Kenmore Model 116 Cannister Vacuum.Trying to get into motor area. Think belt is worn out. I have removed the front two screws under the hinged cover, but can not remove cover over motor.. Still attached at rear. No evidence of any more screws to remove.


Under the cordwinder actuator button, are your other two screws. To remove this cover, take a flat tipped screwdriver and , very carefully, find the "tabs" (there are two) both on the front section under the button. Then, Carefully, press them in a ... Vacuums

Have an old power-mate 116. The height adjustment


Push in on each side of the light cover on top and it will pop off. Then you can remove the (2) access screws. With the screws out the top cover will separate from the base. ... Vacuums

Dyson DC07 will hardly push over new low pile thick carpet. Too much suction. Any adjustments


... Dyson DC07 Bagless Upright Cyclonic Vacuum

I am trying to disassemble a electrolux 2100. I have looked at instructions given by Chemist 1961 and others. On the side, I have removed the rubber covers over the plastic rails but I can't remove the plastic rails that hold the rubber covers on. If I am right, these rails should just slide right out and the outer casing should come part.....or am I doing something wrong. I have pulled and pulled the rails and they don't budge. The rear end won't pop off. Help!


There's a tab at the back of the rail that needs to be released. Turn the vacuum on it's side, slip the tip of a standard screwdrive into the space between the rail and the back of the vacuum, and tap lightly with a hammer. Tap toward the front of ... Electrolux Lux 5500 Canister Vacuum

Height adjust how to repair the height adjust


... iRobot Roomba 415 Bagless Vacuum

My DC 17 is plugged. I can see through the small hole in the top blue "flower shaped" that the holes at the top of the canister are plugged with hair & dirt. I cannot see anyway to get to these small round holes. Is there a way to remove the top blue "flower shaped" piece? I have removed the inner cone from the clear canister but still cannot get up underneath.


Please kindly follow the steps below to clean your vaccum cleaner,1.) Remove the clear plastic handle. You\015\012will have to take out two screws and then unclip from the from the\015\012front. It's stiff, I gently used a flat head screw drive ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Replacing spring in wheel height adjustment


I just solved the problem. Go to this website: http://www.completevac.com/kirby_schemo_5.htmlIt will show you where the spring goes (left side inside the ratchet - when you remove the ratchet you will see that it is hollow. That's where the s ... Kirby G6 Bagged Upright Vacuum

Bosch canister vac BSG81313. Took cover off to remove lots of hair, dirt etc from running without bag in place. Everything went back together OK, but cord reel spring went zip when cover was removed. How do I rewind the spring so there is tension when the cord is pulled out ? Wound cord back onto reel, but reel just clicks ever revolution etc...no tension when cord is pulled out of vac. Bob


The spring inside the hub of the cord wheel has escaped from the locking tab. You must completely dismantle the vacuum to access the cord wheel - take it out, reattach the spring and reassemble the unit. All you need is a phillips screwdriver, a pai ... Vacuums

I have a DC07 and the brush wasn't rotating and I had no suction at the brush but perfect suction through the hose. I noticed a large build up of dog hair around the brush so I took off the cover plate and removed all the hair, cleaned inside the floor/brush housing and cleaned out the hose. I also cleaned the filter and removed the other air access cover and made sure that they were clear. I put everything back and the brush still doesn't turn and there is still no suction through the bottom


Hi and welcome to FixYa. I am Kelly. \015\012\015\012Here is a link that can assist you in your quest for the missing suction: \015\012\015\012 ... Dyson DC07 Bagless Upright Cyclonic Vacuum

I have a Dirt Devil M088400 - Vision Turbo Vacuum. A spring fell from the bottom and the carpet height adjust isn't working. The rollers under the unit won't stay in place either. Can you tell me how to put the carpet height adjust back together?


The roller attaches to wheels. There is a spring that attaches from roller to hight adjustment selector which is a plastic peice with a little hook on bottom that spring attaches to. Both peices should have a hook that the spring ttaches to. ... Dirt Devil Vacuums

How do I remove a motor from a Dyson DC04? The bottom plastic cover can be removed by unsrewing the tork screws but the cover beneath the filter won't come off


I can't say exactly how to do this, but when you can't find the screws to take something apart, they are usually hidden by something else. You did good looking under the bottom cover, but what you're looking for is elsewhere. If there is a seam or ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0468 seconds