Having problems with your Hoover Turbopower Dual U5076 Vacuum ?

Hoover model U5076-930 I can't get in to replace the belt. I can see no screws


Answers :

Please look at this manual:
\015\012http://www.hoover.com/pdfs/manuals/U5046930.pdf
\015\012
\015\012Page #12 shows belt replacement.
Repair Help & Product Troubleshooting for Hoover Turbopower Dual U5076 Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Hoover model u5076-930 I can't get into the motor to replace the belt. I don't see are screws


I don't recognize this model # but most Hoover products have the screws usually silver at the bottom underside of the carpet head. They will also have two additional screwdriver slots mid way along the side of the head on some models. When repl ... Vacuums

Hoover model U5076-930 I can't get in to replace the belt. I can see no screws


Please look at this manual:\015\012http://www.hoover.com/pdfs/manuals/U5046930.pdf\015\012\015\012Page #12 shows belt replacement. ... Hoover Turbopower Dual U5076 Vacuum

Hoover Wind Tunnel U6458-900 Self Propel doesn't work - via other expert advice here for other models of Hoover - I'm thinking it is the actuator that needs to be replaced as I can see the cable does not connect to anything on the bottom. My problem is - I can't get the cover off. Been trying for a couple of hours. I removed every screw I can seem to find but something is hold it down. I also am wondering if/when I do eventually get the cover off, would I need to replace the cable when I replac


On some models there are hook/springs that hold the cover of the base snug. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

I am trying to replace the cable and actuator on a Hoover windtunnel self propelled vacuum. but I cant get the top or hood off the get to them, I have removed all the screws I can see, roller, belts..what am I missing?? thanks so much for any help


Hi there SmartAlec from NelsonVacuums.com.au here. You will need to remove the knobs for carpet/hard floor selection and the carpet height to remove the cover they act as k ... Vacuums

I have a model s3765 Hoover Windtunnel and it was no longer suctioning like it used to. I wanted to see if something was stuck in the rollers. I undid the screws at the base 3 of them and now I see there is a pic that do not undo these screws. I am having problems with getting them back in.


If you can post a pic of which 3 screws you are talking about and where you took them out of i can help u get it back together ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

I have a morphy richards upright hoover model 7333 and i cant get to the belt to see if it is either broken or just come off the runners, i have lost my instructions and cant get the things apart to have a look, does anyone know anything about these hoovers? many thanks, Carina.


... Hoover Vacuums

Manual issues Have reciently purchased a kirby from ebay (gotta love ebay) but has no manual. I believe the model is a heritage (cant see a II though) Do they all have roughly the same manuals??? I have all the attactments - spray painter, hair trimmer, turbo brush etc but really want to get the most from the machine. Where do I get manuals for machines that are 20yo???!!!


Many years ago I was a service engineer for these machines in England they were actually made by a company called Scott &Fetzer in the USA and Branded KIRBY or CIMEX.\015\012\015\012See if Scott &Fetzer are still around and ask th ... Kirby Heritage II Vacuum

The brush is not moving on the vaccume. I'm pretty sure that the belt is busted. I cannot see how to get the shroud off, so that I can get to the roller and belt. It all looks and feels like one piece, even when I start removing screws. It is a bag-less vac. The model number is - v1310rs. Thank you.


I know on my Eureka I had to remove a couple of screws on the bottom and then get a flat blade screwdriver and wedge it on each side of the base kinda next where the end of the roller would be and it snaps up and off. Really weird I thought but that' ... Euro-Pro Shark Professional Upright Vacuum with Bonus StickVac Red Bagless Vacuum

Dead motor I purchased a new motor for my Dyson Animal but I cannot figure out how to get the thing apart to replace it. There are weird star shaped screws but I can't even see how removing those would get me where i need to be. HELP!!!


Ace Hardware or Home Depot should have your star screws ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

I am trying to replace the belt on my bissell. The directions state "remove the screw that holds the red retainer in place, set red retainer arm and screw aside. I see the red retainer but can not get it out I also can not remove the black brush arm that holds the brush in place. I have tried and can not remove it.


Hi, Did you release the handle first before you flipped it over?Have you removed the screw and it still won't come out, or is it stuck even after the screw is out?Are you having trouble getting to it?Please r ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

I want to open a Hoover S3825 Elite Cyclonic Vacuum to see if I can repair or replace the cord reel assembly. Currently the reel slowly draws the cord back into the canister once it is pulled out. I found the mounting screws under the rear wheels once I removed the hub but I do not know how to remove the rear wheels, everything is plastic. The front screws are under the front caster wheels and I think I need to take a screwdriver and pry off the little cylinder wheel to get to them by rotating


... Vacuums

How do you disassemble Rainbow D4c to replace power cord? Took four screws loose but unable to see how to get housing loose...


Gently pull on the rubber gasket that seals the water tank to the canister. Although there are more screws under there - they aren't necessary to remove only to replace your cord. It is the gasket that is holding the motor flange and the plastic hou ... Rainbow 75th Anniversary Canister Vacuum

My electrolux ambassador power wand quit working. I replaced the switch that shuts it off when the roller stops, but it wasn't the problem. The on/off switch is fine, the motor is fine. We have traced the problem to the wires inside the canister by opening the inside cover to the bag container. We see the power cords going into the canister but we're not able to get to anything. We can't find any screws to undo that would open it up in order to follow the wires deep into the canister. We've bypa


... Electrolux Vacuums

Wertheim 1600 Supersystem 1600 Vacuum Cleaner - can't get the last little screw in the middle of underside out so that I can open canister to see if cord needs replacing.


... Vacuums

Rick E1, it looks like the Motor Pulley, Elna #440152-20 needs to be replaced on my 722010 model (flat on one side from standing around. It looks like some kind of a set screw which keeps it attached but are you familiar with how to get this item off the little shaft it is on. Also, any idea where I could find a reasonably priced Motor Pulley.


... Vacuums

I need to replace the cord on an older Hoover upright, model S660, about 1986 vintage. The cord broke where it enters handle. Handle comes apart easily. Just not sure how to pop the switch out without breaking it. Was looking for a manual online to see parts diagram and/or instruction on disassembly and cant seem to find one for that old of vacuum.


Check ebay. those vacuums are worth fixing. I loved them. they would **** the carpet off of the floor! those cords aren't hard to replace.just remember the way you got the old one out. ... Vacuums

I have a Dirt Devil Featherlite Model 085430. It making a horrible noise and I want to open it up to see if anything is broken or lodged in the motor housing. I've removed all the screws I can find and still can't get the thing apart.


Hi,\015\012\015\012The user manuals in this site may be helpful.\015\012\015\012Best wishes. ... Vacuums

Change belts I have all the screws out and I still can't see how to replace the belts. Any ideas how to get the cover off? Thank you


The hooverstore page is down...schematic is here:http://www.vacsrus.com/CartGenie/pg_U8146900.asp ... Hoover U8143-900 Upright Vacuum

How do I clean out the suction side of a Hoover steam-vac Model#f6020-900. I took all the screws out and still cant get it apart.I vacuum before using it, but it still seems to find more hair.


These don't come apart. Hoover makes a thin long tool that will allow you to stick up into this suction side to clean it or use a long piece of galvanized metal strip to slide up into it and clear away the hair. ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

I was changing a light bulb with one of those metal extension rods that unscrew and screw back in the replacement bulbs. It evidently didn't seat correctly and pulled off the bulb and created a quick "poof" type electrical short. I have switched out that bad bulb with a new one and can't get either the fan or lights to work. There doesn't appear to be a reset switch. I also swirched out the wall switch to see if that would make a difference and it does not. Any thoughts or ideas would be appreci


If you have not already done so, I would check at the fuse or circuit breaker panel to see if you have blown a fuse or tripped a breaker. ... Vacuums

I need to open up this Hoover Uprite Runabout deluxe to replace the belt. I dont see any screws to remove to access. Model # U5064-940


You will find them on the bottom of the machine on the brush roll cover. This is the belt you need:Hoover Runabout Deluxe U5064-940 Belt ... Vacuums

Model#F5858-910 hoover steam vac,silver ,spin and scrub. It doesnt seem to spray cleaner it seems to stream it now. what could be wrong? I cant get to end of where it sprays to see if something is blocking it . otherwise it works great. I have it about 8 yrs. always worked good until recently


... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

My Fantom Thunder upright has a blockage that sounds like it is directly above the dirt bin in the "head". I cannot access it from inside the bin chamber by going up the nozzle with a claw parts retriever. (This is the older model where the cyclone nozzle doesn't come off.) The wand, hose, rear inspection port, and front brush intake are all clear. How do I get the top of the vac off above the dirt bin? I don't see any screws or slots.


... LG Vacuums

Model number U5763900 Serial Number 090400013588 Handle broke off just above the four screws that attach it ti the boby of the vac. Hoover does not list parts for models that are more than two years old. The vac operates perfectly but without a handle my wife cannot use it, where can I find a part replacement. easy to remove four screws and replace. dont want to drive 100 or more miles to find a authorized repair shop. Oh yes, this is a Hoover Preferred Wind Tnnel Bagless


Get over it and buy a new one!!! ... Vacuums

Where can I get a replacement glass lid for Rival crock pot model #3100/2? The one listed below is out of stock, but, even if it were, it will not fit my model. Any suggestions? "Buy-it-now-store.com" lists: CURRENTLY OUT OF STOCK, NO ETA. # Rival Crock Pot Lid Replacement Glass for 3.5 Quart Rival Slow Cookers - $5.99 Rival Crock Pot Slow Cooker Replacement Round Glass Lid Cover # Works with Rival Crock Pot Models: 3100, 3101, 3102, 3103, 3130, 3133, 3120, 3250 # Approximate total


... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0804 seconds