Having problems with your Hoover U5180-900 Vacuum ?
Handle stuck handle won't go down. button stuck
Repair Help & Product Troubleshooting for Hoover U5180-900 Vacuum
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
Handle stuck handle won't go down. button stuck
... Hoover U5180-900 Vacuum
The extension wand is stuck. It will go up to a certain point and stop. The gray flexible hose that it is housed in is not damaged and there is nothing on the steel metal rod that slips into the hose that I can see. The gray button on the handle still depresses as well and everything is still "Clicking" as far as the button. thank you
I would try the dyson medic .com this is the place that specializes in the dyson vacuum. Good luck ... Dyson DC25 All Floors Bagless Upright Vacuum
The brush wont turn anymore. I just bought this and it can't handle a stuck cutian?
Check the red reset button you may have over loaded the power brush and it went off on saftey. Also if it is running but the brush is not turning there is a belt in side the unit that wears out and needs to be replaced. ... Bissell 6594 PowerForce Bagless Upright Vacuum
Kenmore 116.35922500 brush wont turn. Seems to come on if handle angle is held at just the right position but it is intermittent. Reset button is not popped up and doesn't seem to have any effect.
... Kenmore Vacuums
Handle wont go to upright position
The red pedal has slipped out of position. On both ends of the red pedal you'll see metal rods (the axel of the pedal). On one side you'll see the metal rod sits into a long groove, on the other side you'll see the metal rod sits into a round hole. T ... Dyson DC25 All Floors Bagless Upright Vacuum
Power Problem Whenver I push the power button on the handle the vacuum stays on for a few seconds then turns off. I have to push the button on the handle all the time to keep the vacuum working.
Hi There,\015\012\015\012Unfortunately this is being caused by static electricity building up in the electronic controls in the handle of the hose. I've seen this problem on numerious occasions, and in fact I have the twin brother of t ... Miele Blue Moon Bagged Canister Vacuum
Stuck sock i have a sock stuck in the handle right where it curves from the hose...i tried a wire hangar but it doesn't budge...does the handle detach from the hose?
Don't put a hanger in there.... Call your local Aerus Service Center and they can remove it for you . If they tear the hose its their responsibility to replace it. If you tear it you are looking at $119.99tx at least. ... Electrolux Lux 5500 Canister Vacuum
Miele S5000 (revolution 5000) vacuum cleaner - How do I open the casing? When the power button on the handle is pressed the green power-level lights on the handle light, but the motor sounds like it gives a little 'jump' but nothing more. The orange power light on the body also dims. I assume the motor or fan is jammed, but I can't open the body to find out. I've taken out to screws inside near either end of the handle, but to no apparent effect. I'm assuming the body is held together by plastic
I have an Easy-Flo central vac unit. The handle on the electric hose has a switch on the handle. With the switch on ''O'' in the center, it's off. On the left, is the ''I'' position. The vacuum runs but the power brush doesn't. On the right is the ''II'' position. The switch won't flip that way. It feels stuck. It feels as if there is something underneath of it that won't let it push that direction. I have the switch out of the handle, but I can't seem to get the actual black casing around the
Switches are not usually designed to be dissembled.I would strongly suggest that you dont take the switch apart. you are better off getting a new one. then if you feel like it you can take the old switch apart and if it dosnt work you still hav ... Vacuums
I have a Eureka Mega Boss Central Vac Model # CV1801P. The suction works when the handle button is pushed left (floor mode) but no suction happens when the button is pushed right. When the floor attachment is hooked up and the button is pushed right, the brush rotates, but there is no suction.
... Eureka Vacuums
Tried pressing in red button and switch next to on button to get roller working but not made any difference - still wont turn (any no suction)
Hi there,I'm sorry to hear you're having difficulty with your DC24. If you haven't been able to reset the brushbar using the reset switch on the cleaner head, I'd encourage you to get in touch with us directly so we can provide further assist ... Dyson Ball DC24 Bagless Upright Vacuum
Barrel Dyson DC08 Origin cord rewind button is stuck.
... Dyson Vacuums
Electrolux oxygen plus 2100w telescopic tube is stuck. I wanted to extend it but the handle will not release and is stuck. Can you offer any suggestions?
I have a electrolux 2000 and my tube has a small tab that you push before it would let me release it. I had trouble getting it off as well. What I did was push the tab, Plasing one foot on the vaccume head holding it down while pulling up and twistin ... Electrolux Vacuums
Power button wont stay on. have to hold the power button manually for it to stay on.
Most likely you have to replace ON/OFF switch. look at detail instructions how to do it on our website:http://www.goodvac.com/kb_results.asp?ID=18 ... Kirby Ultimate G Bagged Upright Vacuum
Ive got a miele revolution 5000 power plus and its just cut out the green power button on the handle is on but the orange button on the body does not come on it just flickers unless i open it up, any ideas?????
Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=640910\015\012Generic problem for all Vacuums\015\012I’ve got a Miele revolution\015\012Posted by ... Vacuums
Dyson 28 handle is stuck in the locked and upright position. Vac runs fine, just can't get the handle to release to run the vac
How do you remove the air duct (plastic sliding piece) that is making the vacuum stay in locked upright p[position? ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
Handle release does not work, seems to be stuck in the downward position and does not keep handle in operating mode
I had the same thing happen to mine and I disassembled the handle area. It was not broken and only needed to be put back in place and has worked since then although I'm very careful when I use the trigger now. Hope this helps. ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum
I have a DC14. About a wk ago it was making loud sound and bar stopped turning. i unclogged everything....now the suction works great. However, the bar still wont turn. The belt inside is still intact and isnt loose. Several solutions suggested resetting the "Red" button...i have searched the vacuum over and over. there is NO red or any other color reset button. The bar is set down perfectly in there, the cover plate is installed properly. What other problems could there be? Or do i just need to
... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum
My roomba wont work. Pushing the power button doesnt do anything. It charges seemingly normal, going to green in a few hours. ive tried the reset trick, holding the power button down with the battery removed. Now what? thanks
... iRobot Remanufactured Roomba Vacuum Cleaning Robot with Scheduler, Case/Color May Vary Robotic Vacuum
I have a Kenmore DuraPower Dual Cyclone Action 12 Amp that just randomly stopped right in the middle of vacuuming. I assumed the plug had come out of the wall so I went to check and this wasn't the issue. I tried multiple outlets and that wasn't the issue. I made sure nothing was stuck and there is nothing stuck. Nothing happens when I press the red "ON" button. What could this be? Thanks!
... Kenmore Vacuums
Handle relase stuck in upright position and I have the vacuum apart and I dont know what to do what am I looking for it is still stuck
Dirtdevil vacuums are so cheap. it's jammed. just go to a vacuum shop and get it repaired ... Dirt Devil Vision Turbo W/Bonus Upright Vacuum Vacuum
The hand-held wand wont slide back into the tube. It wont go down far enough to click in and become the handle again. It was working fine but all of the sudden won't fit back in.
Sounds like the tube has something inside of it that is obstructing the path. veriffy the the "female" end of the tube isnt obstructed, and also, make sure that nothing is bent ( which can happen easily). use a flashlight to shine down into the tubes ... Dyson Ball DC24 Bagless Upright Vacuum
Canister vacuum keeps turning off, can push buttons on wand handle to restart but shuts off again as soon as you start to move handle
Its sounds like the problem is either the power head wire which when your using it and twisting it left and right, turns it off.. Or it could be in the hose where the connect meets with the unit.Here's a number to call to further assist y ... Miele S548 Bagged Canister Vacuum
Simplicity vacuum My vacuum just cut off and now it wont start. I pressed there restart button but nothing happens I have 2 fairly old Industrial hitachi dry vacuum in my workshop both 110v and both wont start. Both i was told were manufactured in Italy and both have a manual and auto switch. It has a black top, takes an orange paper filter inside and its bin is dark blue. Sorry i've forgotton the model number. I've inspected the wiring but it's fine, could it be the motor and how do i gain acc
Just take it in to your vacuum store. ... Hoover U5753-900 WindTunnel Bagless Upright Vacuum
Dyson dc17 hose will not come out/ handle wont release from machine. i've pulled the metal rod up all the way and the handle still won't come away from the machine so i can't use the hose and attachments. anyone know what the problem might be?
Hi there, it is possible that you have a blockage in the wand/hose assembly which is making this difficult to remove. If you are able to remove it to check for this, please contact our Helpline on 1866MYDYSON so that one of our advisors c ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum