Having problems with your Hoover U5194-900 Mach5 Multi-Chamber Cyclonic Vacuum Cleaner Bagless Vacuum ?

Hoover mach 5 turns off after 10 minutes of use


Answers :

I have had problems with the belts on my Mach 5 overheating (smell of burning rubber) and also with the motor overheating and shutting down.
\015\012I learned the hard way that one of the issues might be that the roller/brush on the bottom of the unit has a metal bearing inside the roller/brush that can become clogged with hair (both human and pet hair) which effects performance of the unit.
\015\012Another item to check is if your dust filter is not plugged up which is located behind the removable dirt cup. This is the cup that you remove that collects the dust/dirt/hair from your floor. Take the removable dirt cup out by depressing the gold button and then look behind where the dirt cup sits for filter. This can be cleaned out by washing it with soap and water in the sink but make sure you let it dry overnight before placing it back in the machine. This probably causes some of the overheating when not enough clean air is passing through the machine.
\015\012It’s fairly easy to fix.
\015\012Lay the vacuum on the floor so that you can see the roller/brush. Then remove the phillip head screws that hold the protective plastic plate over the roller/brush. (There are about 6 screws that hold this plastic protective plate in place) Also, you will be removing the (1) screw that also holds the plastic plate over the belts. There are (2) belts that you can remove and when in doubt replace these (2) belts for around $9.00.
\015\012Once you have the protective plastic plate off that covers the roller/brush disconnect the belt is around the roller. Take the roller and cut off any hair that is wrapped around the roller. Next, grab the roller by each end and twist the ends caps and (1) of the ends will unscrew. Once you have unscrewed one of the ends remove any hair or dust that is trapped under this cap. (Be careful not to lose the small metal washer that sit on top of the bearing)You will notice under this cap is a metal bearing that can become clogged and jammed with hair. The hair should come out fairly easy and allow the brush to spin fairly easy once you have screwed the end caps back in place test that it spins freely. If it doesn’t spin freely replace the roller/brush with a new one for about $23.00.
\015\012When you put the belts back on the thick rubber one (Belt # 40201-271) has probably become stretched and should be replaced for about $3.00. The small diameter belt that goes over the roller/brush probably does not usually need to be replaced and does not usually fit very tight. I have heard that people will take the small roller/brush belt and turn it upside down to get a better fit.
\015\012I just did this on my Mach 5 and it runs like a new machine. I did end up replacing the roller/brush head.
\015\012Hopefully you will find this useful.
Check for blockages in the brush bar compartment and hoses and make sure filters are clean.
\015\012Its overheating, and cuts out to protect its self
Repair Help & Product Troubleshooting for Hoover U5194-900 Mach5 Multi-Chamber Cyclonic Vacuum Cleaner Bagless Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Hoover Mach 5 turns off after 5 minutes of using. Can you advise the problem?


5 minutes everytime? If so, raise brush all the way, and vacuum next to nothing. in fact, tilt vac up so the brush touches nothing. wait 5 minutes. If it doesn't shut off, your brush is set too high. if it does, the motor is over heating. make sure b ... Hoover U5194-900 Mach5 Multi-Chamber Cyclonic Vacuum Cleaner Bagless Vacuum

I forgot to replace the vacuum cleaning bag in my Hoover Wind Tunnel Supreme Mach 3.3! It overheated and turned off. I spent all afternoon cleaning the dirt out of the inside, filters, etc. It still overheats when used over 1 minute. Do I need to buy a new vacuum?


... Vacuums

Hoover mach 5 turns off after 10 minutes of use


I have had problems with the belts on my Mach 5 overheating (smell of burning rubber) and also with the motor overheating and shutting down. \015\012I learned the hard way that one of the issues might be that the roller/brush on t ... Hoover U5194-900 Mach5 Multi-Chamber Cyclonic Vacuum Cleaner Bagless Vacuum

I have the same problem as discussed above. My Hoover Pet Cyclonic upright stops working while using it. The bottom feels hot when this happens. When it first occurred, I emptied the canister and even tried a different plug. It did not turn back on for over an hour. When it did turn back on, it would die again after about 3-5 minutes of use. I don't know what else to try. I have washed the secondary filters, let them air dry and replaced them and this did not help the problem. My friend,


... Dirt Devil Hoover Uh70085 Pet Cyclonic? Upright Vacuum

My Hoover Windtunnel cuts off after using it for a few minutes. After an hour or so, I can turn it back on again. This keeps happening every time I use it. This is my third one. I have taken the other two back to Target for the same problem and they have exchanged them.


Yes this machine has a thermal protector in it to shut off the machine if it gets to hot, this is normal. if there is no clogs in the hoses or in the machine then you will need to wash the filter at the top of the machine. you will have to remove the ... Hoover U5780-900 Windtunnel Cyclonic Bagless UprightVacuum

My brand-new Hoover Windtunnel T-Series Pet Rewind Bagless vac simply shut off while I was using it and now I can't get it to turn back on. I've emptied the dirt collection bin and let the unit sit unplugged for 30 minutes to reset the Thermal Protector as per the manual. I've even tried a few different outlets just in case a fuse got tripped, but the vac still won't turn on. What happened? Do I need to return this vac to the store? I just bought it 5 hours ago.


... Hoover Vacuums

Hoover turbo cyclonic only 12 weeks old stopped working while cleaning. I was using the hand tool and after about 3 minutes it just stopped and will not turn back on.


Try changing the fuse in your plug ( uk ) if this fails to fix it , have it repaired under warranty \015\012 \015\012\015\012 \015\012 ... Vacuums

Mach 5 hoover turns off


Just got a solution off another website. There is a pre motor filter about the dust collection container. I opened mine and it was very dirty. I washed the filter and you are supposed to let it dry out for 24 hours. Hopefully this will work. Ano ... Vacuums

I have a Hoover Mach 2.7 Windtunnel that shut off during use and wouldn't turn back on. Was doing kitchen floor and running fine. Though a breaker tripped but didn't...what could it be?


Hello, \015\012\015\012It sounds like your thermal reset switch inside of your Hoover may have gone bad. When a vacuum cleaner doesn't turn on it, it's either caused by one of four things. \015\012\015\012Ele ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

My hoover mach 5 stopped during use and will now not turn on


If the machine overheats, a breaker trips. Most breakers reset themselves after they cool off. You may have a manual reset button to push on your model. The machine will overheat if the bag is too full, or if the exhaust port is clogged. The rese ... Hoover Commercial C1660-900 Bagless Upright Cyclonic Vacuum

Hoover tempo upright is clogged. I can only vac for a few minutes, then I have to unplug it and turn it over and clean out the under part under the roller. It is totally stuffed with dirt and dust and carpet fibers. I have a new bag in. It is like it is clogged up inbetween the bag and the roller. Also gets clogged when using the hose. It is maybe a year old. How can I take it apart and unclog it?


Disconnect the hose and head and wands. Drop a quarter thru the hose, the handle sometimes clogs. peer thru the wands and inspect the elbow on the head for blockage as well ... Vacuums

Hoover zoomi stops working after 15 minutes vacuuming, and takes at least 30 minutes to turn back on?


... Hoover Vacuums

Hoover mach 5 only used 3 times


If the filters are ok, and there is no clog in the hose or dirt inlet down by the brushroll, then the motor protector is probably bad. ... Hoover Commercial C1660-900 Bagless Upright Cyclonic Vacuum

CUTTING OFF Our Dco7 cuts off after a few minutes of use. If we wait a few minutes and power it back on it will turn on but turn off again by itself.


Ok What is probably causing the problem is an internal error inside the vacuum. What I recomend you to do is take it back where you bought it and tell them what ever is wrong with it.PLEASE RATE MY ANSWER AS SOON AS POSSIBLE! ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

I have a vax power 6 hoover, this was bought in January this year replacing the previous 2 I had bought in 2012. I get the same problem each time in that the hoover cuts out after using it for 5 minutes and I cannot use it again for another half an hour. WHAT IS THE PROBLEM WITH IT?


... Vacuums

Have a Centralux Aerus about 5 years old. Don't see a model number. There is suction but beater brush quit working. Was using for a few minutes, shut it off for a few minutes, turned it back on and suction only. Tried the reset button also. Tried the sidekick attachment and it works fine. There was no smell like something was hot. Belt is fine. Are there any fuses or anything else to try? This vacuum cleaner has not really been used that much, it is hard to believe the motor would need replaced


There probably is a loose wire in the handle near the switch or a wire off near the swivel elbow near the vac power head. With the right fastener tool to remove some screws you can fix it yourself ... Electrolux Centralux Vacuum

Hoover Mach 6 U5198-900 vacuum roller brush won't turn. I had opened the bottom to clean hair off the roller. the belts are not broken. When I closed it and turned it on, now the roller brush won't turn. I can push and turn it by hand, but not easily. Then I noticed the brush on/off switch is turned off, but when I step on it, it won't turn on. I was thinking I let something get out of place when I opened the bottom, but can't see what.


... Hoover Tempo Widepath Upright Vacuum - Blue

My Hoover Windtunnel Ultra U6425-900 began shutting off after a few minutes of vacuuming. The time interval became shorter and shorter. If I leave it sit a while, it will start again. This does not happen when I used the attachments - only with the floor brushes. The switch has recently been replaced and the whole vacuum serviced by a Hoover dealer about a year ago. I have been told by a local repair shop(not a Hoover dealer) that it is the motor, there is nothing to do other than replace t


... Hoover Vacuums

My vacuum just stopped working, so I don't know what the problem is. I used it in the kitchen to vacuum the hard wood floor. I turned it off, and a few minutes later, turned it back on to finish vaccuuming the kitchen floor. It just would not turn on. I had not unplugged it or did anything to it. I then tried to see if it would work in another plug, and no luck. I'm trying to figure out if it can be fixed or if I need to look for a new vacuum.


When I get most Vacuums that have dies on people most of them the wire has been worn and cut one or more wires on the plug cord. Sometimes the cut can be over looked. Please unplug and check the wire carefully.Also please post the make model a ... Kenmore 23913 Progressive PowerMate Bagged Canister Vacuum

I HAVE A BRAND NEW HOOVER MACH-3 CYCLONIC THAT CUTS OFF EVERY FEW MINUTES. IT IS DRIVING ME CRAZY! IT'S LIKE AFTER 5 MINUTES OF VACUUMING IT HAS TO SIT FOR A LEAST AN HOUR THEN YOU CAN VACUUM FOR ANOTHER 5 MINUTES. HELP!


If it were mine and it was brand new I would bring it back and exchange it. It sounds like the motor is over heating and shutting off automatically. Does not sound good. My advice return it. ... Vacuums

Kirby G5 I was using the hoover and just switched it off and turned it on again but would not turn on. I changed the fuse in the plug but still wouldnt turn on. what should I do?


See my troubleshooting guide and from there, you can view my do it yourself guides for fixing your Kirby. ... Kirby G5 Bagged Upright Vacuum

I have a Hoover Turbo EmPower 4600 and the roller will not turn when we turn on the vacuum. The vacuum is fairly new, and hasn't seen too much use, but now the roller won't turn, so it's not picking anything up. There also doesn't appear to be a belt or any way to take this apart. Can you help me? Thank you!


The beater belt is broken. There are 4 phillips head screws on the outside (2 on top of the base on either side of the upright, and 2 on the front edge on the underside of the base near front edge). and 4 phillips head screws on the inside (holding ... Hoover Vacuums

George i have just bought George from a friend and he has never used the wet side of things . When i turned the hoover on i cant seem to get the wet button to work. Do i have to have the hoover main button on first and then press the wet button?


The pump can seize up if the the system is not flushed with clean water after using carpet shampoo. You should run half a tank of clean water through Geroge before putting him away.The only solution is a new pump or pump motor. ... Numatic GVE370 Canister Wet/Dry Vacuum

My Windtunnel 2 keeps turning off after a few minutes or even seconds of use. We thought at first this was the thermal shutoff feature but this happens regardless of how long it has been turned off. The bag is empty and it doesn't appear there are any blockages. We purchased this a little over a year ago and are about ready to toss it.


Bought a BissellUnsubscribe us, we do not want to pay money for help support ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

I lost the manual for my hoover steam cleaner spot. and now i can't figure out how to use it. i've only used it once before and i can't remember how to get it working. the water will come out but it just floods the floor when i turn it on. what do i do?


Hi,Here is a link to your manual. Hope it helps.http://www.retrevo.com/support/Hoover-F5505-Vacuums-manual/id/8231dj681/t/2/ ... Hoover F5505 SteamVac Spot Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.2113 seconds