Having problems with your Hoover U5264-930 TurboPower Bagged Upright Vacuum ?

Problem with wheels

\015 When I start up my vacuum it smells like rubber. \302\240I think the adjustment for the different carpet types is broken. the wheels appear to be sitting to low, making the brushes sit right onto the carpet. \302\240I can't tell if a piece is missing or how to re-attach adjustment piece. \302\240Help!\015

Answers :

If the belt is over a year old, it should be replaced. This is normal maintenance and is often overlooked. When the handle is in the upright position, it will appear the the height adjustment is not working. What's actually happening is that the height adjust is easily moved so you can make any adjustment you want. When the handle is pulled back, the front of the machine will lower to that setting and lock, so it will not adjust itself while you are vacuuming. If you wish to change the setting, you have to return the handle to the upright position, or you can lift the front of the machine with your hand, taking the weight of the machine off the wheels and this will allow you to slide the adjustment to another position. It is possible that the adjustment mechanism has come apart. It is comprised of three separate components. It would be very difficult to explain it here and should be addressed by someone familiar with this model.
Repair Help & Product Troubleshooting for Hoover U5264-930 TurboPower Bagged Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Ihave a Hoover Windtunnel self-propel model U6445-920. The belt from the drive motor to the big wheel will not run in the center of the wheel. The belt runs about 1/3 off the wheel. I have tried several new belts and still the same problem. What do I need to do to repair this problem.

The large wheel may be worn off center. If the belt stays on and is not thrown, you can run the vac. if there is wobble in the wheel causing a genuine belt to slide off replace the wheel mechanism. ... Vacuums

Both of the wheels are wobbly and loose on my Kenmore upright vacuum model 721.37060. I don't see where I can remove them to analyze and fix the problem, which seems to be that the wheels are loose on their axels. How do I get the wheels off and what do you think I'll find inside?

Most if not all vacuums have an access panel on the bottom.It may be held on by a couple of big plastic clips,the kind you squeeze together and it releases a door.Some have plastic screws.There may also be a couple of phillips screws along with it or ... Kenmore Vacuums

Front wheel problem

I would send it to protechrobotics. they will test all your components and let you know what needs to be done. if the repair is more than it's worth--they will help you out too.http://www.protechrobotics.com/ ... iRobot Roomba 4210 Bagless Robotic Vacuum

Will sew for 2-3 inches and then slows and stops. Hand wheel very stiff. End having to remove fabric and start over turning hand wheel until it loosens and then will sew for few inches and repeat the problem.

... Vacuums

Floor tool wheel will not revolve on dyson dc08 origin vacuum - seems to be jammed. How do I disassemble the unit to fix the problem with the wheel. Everything seems to be clicked in. I do not want to force anything - I might just break it. Any help will be appreciated. Thanks.

Hi,The wheels on the floor tool get junked up with hair pretty quickly, at least they did for our Dyson. The metal peg that holds them in has grooved teeth to prevent it coming out easily, but it will come out if you get a claw hammer an ... Vacuums

Hoover problem the wheels on the bottom of my upright have come off , i have put them back on but i do not know where the metal clip should go and also the height ajuster for the wheels does not work, any ideas thanks kevin oates

The metal clip is a leaf spring and there is a slot for it, You may have to pull the cover off, may have a broken piece for the adjuster. Would help to have model number. ... Vacuums

How to take apart the Hoover U6437-900 to change the belt and clean it. I have the belts and I have removed several screws. It looks like the knobs for the wheel carpet height and carpet to floor selection are the problems but I can not figure out how to remove the knobs. Besides, I am not certain if this is the problem. Do you have the instructions? Thanks

HERE IS THE MANUAL > http://hoover.com/file/500/ ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Took apart my cleaning brushes and all on my bissell spotbot i need diagram of how to fit the head part back to the machine. I had a problem with the auto not working i have fixed that problem just need to see so that i can get it back togoether. I assembled the whole wheel back but cannot caonnect it to the machine LOL

... Bissell 1200A SpotBot Pet Robotic Vacuum

I have a Hoover Wind Tunnel U6439-900, Series Q12,0A. I am not sure but I think, from reading other's problems, that it might be the idler arm. When I put the handle down the small wheel beneath t

... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Problem with wheels

If the belt is over a year old, it should be replaced. This is normal maintenance and is often overlooked. When the handle is in the upright position, it will appear the the height adjustment is not working. What's actually happening is that the heig ... Hoover U5264-930 TurboPower Bagged Upright Vacuum

How is the V-belt tension adjusted (Hoover Model U6439-900)or how do I know if the tension is correct? There seems to be a lot of "play" in the belt and I'm wondering if that is the reason the brush roll only turns as the wheels turn, regardless of the carpet height setting. And yes, the brush roll is set for carpet, not hard floor. Or is the cause of the problem something other than the V-belt? A new flat belt was installed when the machine was professionally serviced so I assume (?) that was a

The V-Belt is not adjustable. There are two ways the belt has no tension: (1) when the handle is upright, a mechanical lever takes the drive tension off the belt, and (2) the brush roll lever setting you described. The upper handle would have to be ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

I have the Eureka 4870 "The Boss" Smart Vac. The beater bar began to turn constantly and can't be shut by moving the Brush Roll Contol to Bare Floor position or the machine to the upright postion. It has also eaten two new belts. A local tech says he has seen this problem whereby the free-wheel assembly that makes contact with the belt to engage the beater bar is misalgned and cannot disengage. It is usually the chassis which would mean replacement of enough parts that would not be worthwhile

... Eureka Smartvac 4870 Bagged Upright Vacuum

The wheel is not turning, and the motor seems to have a problem because it is smoking. Smoke coming out of the bottom where it would normally touch the ground when sucking. Model: Nissan 82g7-1.

... Bissell 82G71 Upright Vacuum

Roomba 530 clicks steadily as it moves, and has a limp, so something is catching inside it - inspection suggests not the brushes, not the wheels, so maybe the electric motor? Any ideas as to problem or where I can repair? Thanks. Bill

Symptoms suggest the clicking is coming from the wheel switch, and it must be disassembled and cleaned. ... iRobot Roomba 530 Robotic Vacuum

The brushes on my Bissell 9200 have stop rotating. The microswitch near the wheel seems to be OK. How can I troubleshoot the problem?

If the belt is still OK and you can turn the brush by hand (make sure the power is off when you try) then there is only the drive motor and the power switch left in the circuit. Bissell's are very simple machines and you can easily remove the topc ov ... Bissell 9200 Upright Vacuum

Press the power button on - good got a green light (new battery) press the clean button - got a green light iRobot runs for a couple of seconds and stops, then starts, then stops. After two or three times I now have a red light on for the Status. All of the wheels seem to be clean. I used compressed air to clean the underside. But still have the start stop problem.

How many times does the red light blink before it pauses? ... iRobot Roomba Discovery SE Bagless Robotic Vacuum

My DC-25 will not return to the upright position. I emailed Dyson support and the response was: "The DC25 stabilizer wheels will not lock into position if the “spokes” on the red pedal are not seated correctly." I agree with that assessment, but cannot figure out how to get the spokes on the red pedal to seat correctly. The manual is useless for this problem since that part of the vacuum cleaner came already assembled, so the manual does not address it. Help.

It sounds like the undercarriage unit has failed. It is a common problem on ball models. The DC25 is a recent model so would still be under Dyson's 5 year guarantee. Get them out to it. ... Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum

Bought today a used rca rp3721a clock radio without the manual. need user manual to adjust all the settings, for example TIME, ALARM TIME, ALARM ON AND OFF, radio or "beeper" alarm on, entire unit on and off without unplugging it from shore power,and anything I haven't thought of up to here. The unit is RCA Model RP3721A clock radio, and appears to be functional. Our problem seems to be "the nut behind the wheel". e-mail: [email protected]

Hello,I advice you check the links below to search for the\015\012manual of your device, the link contain almost virtually all the manuals of all \015\012device.manualsonline.comORmanualnguide.com ... Vacuums

Squeaky wheel I don't want to take apart more than I have to. The front cover has been removed and I tried using WD40 on the squeaky areas but the problem has not been resolved.

... Dyson Slim DC18 All Floors HEPA Bagless Upright Vacuum - Iron/Titanium/Yellow

Detergent does not dispense on the foward stroke with trigger pulled, clean water does come out on the backstroke. Is this a relatively easy fix? I see some sort of rocker switch attached to one wheel, is this the problem?

I believe the rocker switch your refering too is the switch to shut the brushes off when in the upright position. As far as the solution problem.\015\012Determine if the valve cap is clogged if detergent won't dispense from the Hoover cl ... Hoover F7425-900 SteamVac V2 Widepath Upright Vacuum

Roomba stutters on one wheel causing it to quit

Try setting the Roomba on the floor, powering it up, pressing down hard on the front, just above the front wheel, and hitting "clean" or "spot." My Roomba had the same problem, and this seems to do the trick for it. I think it has something to do wit ... iRobot 4150 Roomba Vacuum

Castor wheel on Roomba falls off

... iRobot Roomba 560 Robotic Vacuum

My bissell7901 is spraying water out by the wheels

Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

Hello the problem i have with my roomba is? it

The best course of action is to do as it says and remove the base plate and the wheels and clean them. Don't neglect the caster in the front when you clean the two drive wheels. ... iRobot Roomba 560 Robotic Vacuum

IRobot is only moving 1 inch back and fort, wheels are clean

You will need to replace the cliff sensors. One one two IR LEDs are damaged. ... iRobot Roomba 560 Robotic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0289 seconds