Having problems with your Hoover U5269910 Bagless Upright Vacuum ?

The vacuum cleaner does not pick up anything from carpet. It does not even pick up pieces of thread laying on carpet. On tile floors it blows dirt away instead of picking it up. I've tried all the settings on the brush and nothing works. It has done this since new

Answers :

Sounds like there is a clog..
\015\012Usually its in the hose - look closely.. Stretch the hose out straight and look in there good..
\015\012Or a clog could be in the vac close to where the hose conects to the vac on either end..
\015\012This is most case scenario with these types of vacs..
\015\012I hope this helps !!
\015\012Please rate me good ;o)
Repair Help & Product Troubleshooting for Hoover U5269910 Bagless Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

The vacuum cleaner does not pick up anything from carpet. It does not even pick up pieces of thread laying on carpet. On tile floors it blows dirt away instead of picking it up. I've tried all the settings on the brush and nothing works. It has done this since new

Sounds like there is a clog..\015\012\015\012Usually its in the hose - look closely.. Stretch the hose out straight and look in there good..\015\012\015\012Or a clog could be in the vac close to where the hose conects to the v ... Hoover U5269910 Bagless Upright Vacuum

My Kirby Heritage II vacuum is not picking up dirt up out of the carpet like usual, and I have to keep setting it lower to pick anything up. I finally get it to such a low setting that it starts sucking the carpet up and makes a whirring noise, and starts smelling. Every time this happens, we find the belt has been burned. We are wondering if the brush roll inside with the brushes that pick up dirt are worn out and too short?

... Kirby Heritage II Vacuum

For some reason, when I tried to put the floor vacuum attachment back on and vacuum the carpet, I realized that the belt was not engaging. the belt is in there and not broken, but it is not turning the beater brush. it is just hanging loose around the brush. When I turn the wheel to engage the brush, it picks the belt up, but when I attach the vacuum to the attachment, the brush is just not turning.

... Kirby Ultimate G Bagged Upright Vacuum

The hose works great, but the head of the vaccuum does not pick up anything !!! I checked every opening that may have been clogged, but nothing came up. When I hold my hand under the brush/roller, it seems to be putting out more air than intaking air. Particles "dance" on the carpet, but don't get "sucked up" into the vaccuum ? I have had the vaccuum only 1 year, so the brushes should not be a problem. I changed the bag, and checked the belt. The belt and brushes seem to be OK. ?

Hi there,Uprights are notorious for debris forming clogs when changing direction. The 90 degree turn where the base suction goes up. Have a closer look . You may need to pull the base plate off to access the blockage.Best reg ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Isn't picking up lint. Will pick up other things like flecks of paper but will not get any fuzz or fibrous material off any rug no matter what the setting. This is a recent problem. Have owned the vacuum for awhile and never seen this issue before. Is it an easy fix? I've cleaned the brush, cleaned out the filters, cleaned the dirt tank. Nothing changed.

Is the brush turning on the bottom of the machine ? If not It could be clogedup with stuff or the belt could be worn on it and it will turn but as soon as it contacts the floor it will stop turning. The belt is easy to replace by removing screw ... Bissell 3576 CleanView II Bagless Upright Vacuum

Comcast dc50 Hi my vertually new dc50 doesn't seem to be picking up. It's not making the louder sound that it makes when the brushes go round and nothing is picking up in the cylinder, it's just building up flick in the head and depositing it back on the carpet in clumps :-(. Please help .....

... Dyson Vacuums


It could be that you need to replace the belt. Here is the belt you need:Dyson DC07 Belts and Manual ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Chatter We have a Kirby Ultimate G. Since we purchased it it bounces across the floor and the level of the sweeper has nothing to do with it. To get it to stop, it has to be at the highest level. The place we bought it, has done nothing to help us. We tried a new beater brush, no help. If I have to use it at it's highest level to sweep my carpet, I might as well not waste my time. ANy suggestions?

Http://www.geeksquad.fixya.com/ThreadView.aspx?prdid=11557&thid=576381\015\012Chatter\015\012Posted by CANRN on May 06, 2008\015\012We have a Kirby Ultimate G. Since we purcha ... Kirby Ultimate G Bagged Upright Vacuum

Brush is not spining when it touches the carpet. I tried setting multiple levels .. no use.if it not touching carpet then gr8 spinning like it is the king. I have used it ..may be 8 or 9 months.

Hi,\015\012\015\012time for a new belt,\015\012even though the belt is intact, its lost its elasticity and is slipping.\015\012good luck\015\012\015\012J ... Bissell Vacuums

I have a Miele S1721 Powerhouse upright vacuum. When the belt broke I took it into the shop (because when i tried to replace the belt, the tension was so tight I couldn't get it back together!!). When I got it home I DISCOVERED THAT THE HEIGHT ADJUSTMENT DIDN'T WORK anymore. It seems like it's set really hight, because it no longer contacts and brushes the carpet. So it's now useless. I went back to the shop and the tech denied that there was anything wrong. (I didn't have the vac with me). No

Hi\015\012The Miele uprights (S170 and upwards) with the Powerhouse title are ALL Panasonic uprights which have been at one time sold in the UK. Therefore the upright may use TWO drive belts which need to be looked at: Take off the sole plate a ... Vacuums

I have an Electrolux LITE upright carpet cleaner - about 15 years old. Suddenly last night when using it, from the normal motor (whooshing) sound, the motor suddenly went very slow and with a slight grinding sound. The brushes are now just turning round very slowly and areobviously not picking up anything. Has the motor gone or is this repairable, or should I just get a new cleaner? I have tried to open the machine from the bottom to see if anything is obviously wrong, but it looks complicated a

... Electrolux Vacuums

Now that I just fixed my Lux Legacy canister vacuum, I need help on my other Electrolux Regency Series upright! The vacuum works fine but the rotating brush does not work and the brush motor does not turn on. Tried cleaning the brush and hitting hte reset button to no avail. This upright has a triple setting switch and I checked the each of the wires seem to be attached. Tried rotating the brush by hand and it would not budge. Was going to "encourage" the brush to turn with a set of articula

There are a couple rectangular holes on the bottom of the power nozzle, beside the wheels. These have tabs in them that need released with a standard screwdriver. \015\012 ... Vacuums

Hoover Windtunnel U5750-900 Agitator brush is weak. It turns fine if I tilt the vacuum back, but it slows to almost 1/4 speed when it touches carpet, even on the highest carpet setting. I've replaced the agitator belt twice. The brush used to turn powerfully even on the lowest (Hard Floor) setting. Ideas? I should probably lube the agitator brush ball bearings, and re-check the belt, but, other than that, I'm stumped.

... Hoover U5750-900 WindTunnel Bagless Upright Vacuum

In Carpet setting, the vacuum brush does not spin

I put 3 turns of electrical tape around the area of the beater bar that meets the vacuum belt. This solved the problem short of replacing the beater bar. ... Eureka Smartvac 4870 Bagged Upright Vacuum

Brush bar on Dyson DC19 doesn't work properly on carpet setting

... Vacuums

How is the V-belt tension adjusted (Hoover Model U6439-900)or how do I know if the tension is correct? There seems to be a lot of "play" in the belt and I'm wondering if that is the reason the brush roll only turns as the wheels turn, regardless of the carpet height setting. And yes, the brush roll is set for carpet, not hard floor. Or is the cause of the problem something other than the V-belt? A new flat belt was installed when the machine was professionally serviced so I assume (?) that was a

The V-Belt is not adjustable. There are two ways the belt has no tension: (1) when the handle is upright, a mechanical lever takes the drive tension off the belt, and (2) the brush roll lever setting you described. The upper handle would have to be ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Dirt devil vacuum cleaner--trouble vacuuming dirt and pet hair on carpeting --is the problem with the spinning brush which contacts the floor,  not contacting the carpeting??  I thought (when I bought this vacuum) that the aforementioned brush was adjustable to various heights of carpeting.  Sometimes, it seems like nothing is being vacuumed up --unless I have just put a new bag on the vacuum... Do I need or can I replace the spinning brush on the bottom of the vacuum so it kicks up and vacuums

Try replacing the belt. Rubber belts stretch out after about a year. ... Dirt Devil CE6100 Featherlite Upright Vacuum

Stopped running My mother's Oreck vacuum sound as if there was something bogging the rotating brush down. I pulled the bottom cover off and found nothing wrapped around or restricting the brush. I tried to finish vacuuming with the problem then I turned it off to move a chair and turned it back on it would do nothing. Any suggestions as to what could be causing the vacuum to sound as if the rotating brush is being restricted from turning. There was not odor of burning as if the motor was in a bi

Orecks have a plastic fan inside and everything you pick up hits it, sometimes things can get stuck in there or break the fan locking up the motor. With the machine off, poke around where the dirt goes into the motor, behind the roller and see if you ... Oreck XL Ultra Bagged Upright Vacuum

Brush Roll belt stops turning durring vacuuming on WindTunnel self-propelled, v belt is a little loose with handle down. Tensioning roll is engaged OK, but fully at the end of its travel. Replaced belts flat and v, but still stops turning even on high carpet setting when vacuuming. Carpet setting and height adjustment appears to be working OK, roll is clean and turns easily when out. Also turns easily until it engages the carpet. Self propel function works just fine.

... Hoover U6485900 Bagged Upright Vacuum

Carpet setting not working, no brush turn, no light, etc.

If the motor is running, its the belt, if not there is a break in your wire likely in the stub going from the wand to the head ... Kenmore 25614 / 25615 Progressive Bagged Canister Vacuum

Ive got a dc07 dyson just changed the belt on it as i had to since then it isnt picking anything up at all nothings clogged up had it to bits and put it all back together again properly. The hose is working when i take it off its got plenty suction but when i run it along the floor it picks absolutely nothing up any ideas that i havent thought off. Thanks

Sounds like the hose underneath has become detached. Have a look and if its not that come back to me. Also can yo9u check your U Bend is still on as these can come off. ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Does the epic 3500 have a belt? It seems that when running on the carpet setting, it is very noisy and is not picking up the way it should. When we run it on the floor setting, it sounds better, but the rolloer doesn't go around to fluff the carpet. What is wrong?

Yes, it does. It definitely sounds like a broken belt. And the noise would probably be due to the belt still being in the machine and hitting the motor shaft.\015\012Due to some difficulty in reassembling the powerhead and getting the belt to ... Electrolux Epic 3500 Vacuum

I set up my ONYX SW2300XS which I recieved as a gift (so no reciept) for the first time today. At first it was working well, I inserted a dvd and it played well. I played with the zoom and the skip buttons on the remote a bit and left it playing while I went a did other things. I came back about halfway thru my movie and wanted to skip scenes but the remote did not work. So I tried the NEXT button on the machine. This did nothing, so I tried the STOP button and that did nothing, the dvd was

Mine does the same thing! The store told me it would play all formatted but it does not! Its junk!! ... Vacuums

I recently purchased this vacuum after reading consumer reports article on it and from recommendations from family. However, since I've had this vacuum it's been nothing but problems! I have a frieze carpet and I have the vacuum set on the highest setting. Each time I use it, the vacuum clogs with carpet fibers before I even finish a room! Any suggestions?

Is that a shag carpet? the power head is raised up all the way can you lower the suction on it is the carpet old the vacuum may not be able to handle the carpet,go to a vacuum store and see if you can try somthing else out some stores well let you re ... Hoover Tempo Widepath Upright Vacuum - Blue

Carpet setting: the brush drive does not work with the carpet setting. Is there a way to remove the bottom to determine if something is caught in the system?

To determine if you have a clog, first remove the attachment hose like you were going to put an attachment on. With the vacuum in the upright position, turn the vacuum on and place your hand over the hose. Do you feel a strong suction? If not remove ... Kenmore Progressive Bagless Upright with Inteli-Clean SystemVacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1005 seconds