Having problems with your Hoover U5434-900 WindTunnel Plus Bagged Upright Vacuum ?

Changed belt. have burning smell - Hoover U5434-900 WindTunnel Plus Bagged Upright Vacuum


Answers :

Take it back apart, check it again. Check the plastic where the belt is running for burnt spots. Also check the brush roller sometimes the tension from a new belt can finish off what was left of the bearings and cause the plastic end caps and roller to melt. Pull out the roller and try to spin it while holding the end caps. If it doesn't spin or spins hard there's your smell. Most times when the rollers go bad they break the belt. Replace the roller if necessary Make sure the roller is in correctly and flush and that the bottom plate goes on easily.


Good Luck
The Vac Dr.
Repair Help & Product Troubleshooting for Hoover U5434-900 WindTunnel Plus Bagged Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Changed belt. have burning smell - Hoover U5434-900 WindTunnel Plus Bagged Upright Vacuum


Take it back apart, check it again. Check the plastic where the belt is running for burnt spots. Also check the brush roller sometimes the tension from a new belt can finish off what was left of the bearings and cause the plastic end caps and roller ... Hoover U5434-900 WindTunnel Plus Bagged Upright Vacuum

Hoover Windtunnel Bagged upright vacuum is smoking and belt is slitting and burning


You probably need to replace your brushroll seeing that your belt is burning means motor is turning. first check you brushroll and see if there is an obstruction keeping it from spinning if its not spinning freely replace ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

I have a Eureka 4800 series the Boss upright with a bag and Hepa filter. I love it! I was just vacuuming with the hose part and all was well and then suddenly the lower brush came on and a "burning" smell followed. Thought it was the belt so my husband was going to put on the new belt which I had on hand! When he turned it over, the "bar" that holds the belt looks as though it "shot through" the plastic side of the housing on the vacuum. There is melted plastic on the outside of the vacuum and o


I had the same problem. Take out the old belt if possible. Remove the 4 screws inside the filter and the 3 on the front of that housing. pull out the foam around the motor. carefully pull out the suction tube that is press fit against the motor. ... Eureka 4874 Bagged Upright Vacuum

I have the bissell power force bagged upright vacuum and the brush is not turning, I have replaced the belt but the brush will not move but the metal piece that is hooked to the motor that spins the belt and brush is turning but the brush won't, and the belt starts to burn


Sounds like your brush roll is seized. Remove the brush roll (see picture) and make both of the end caps spin freely. If not, replace it and you should be set. *An example of a brush roll* ... Bissell 3522 PowerForce Bagged Upright Vacuum

Replacing belts on U3109 hoover vacuum - Hoover Ultra U6430-900 WindTunnel Bagged Upright Vacuum


... Hoover Ultra U6430-900 WindTunnel Bagged Upright Vacuum

How do I replace a hoover windtunnel belt - Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum


Here is a link to the manual and to the belts you need.\015\012\015\012\011\011\011\011\011\011U6439-900 Manual \015\012\011\011\011\011\0 ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Belt won't stay on - Hoover Ultra U6430-900 WindTunnel Bagged Upright Vacuum


A belt will slip off because it is stretched, or the brush bearings are worn, or the motor drive shaft is misaligned. Hoover belts fit snug. After as little as week they begin to stretch. Even though they are not broken, they will spin lo ... Hoover Ultra U6430-900 WindTunnel Bagged Upright Vacuum

Belts keep burning up when i turn it on - Oreck XL2000 Bagged Upright Vacuum


The brushes probably have strings or excesive carpet fibers where where it meets the base of deck and the cover remove screws from bottom pop out brushes and remove string and reasimble ... Oreck XL2000 Bagged Upright Vacuum

Drive belt won't turn - Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum


Hi try w,d 4o spray on wheels each side ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Replace hoover belt 40201160 - Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum


You usually have to unscrew the bottom and take it off to get to the belt and then you have to stretch it back on usually a quick fix ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Brush does not turn because belt is loose - Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum


You need a new belt that isn't stretched. You can get a replacement here:Hoover Windtunnel Belts ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Replace belt on Hoover Model #U6430-900 - Hoover Ultra U6430-900 WindTunnel Bagged Upright Vacuum


... Hoover Ultra U6430-900 WindTunnel Bagged Upright Vacuum

How to put on the flat belt on hoover mach 5 - Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum


Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=681386\015\012Generic problem for all Vacuums\015\012How to put on the\015\012Posted by jamescook76 on ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

V-belt flapping on Hoover Self-Propelled WindTunnel Bagged Vacuum


... Hoover U6441-940 WindTunnel Bagged Upright Vacuum

The original belt on my upright Kenmore Progressive broke and I replaced it with the spare that was in the vacuum. The vacuum and spare belt are about 10 years old. Then the spare broke after one vacuuming session and there was a burning smell coming from the vacuum. I ordered new belts and replaced it with the new belt. It seems to be working fine with no smell. I checked the belt after I vacuumed the family room and although it was in tact, the belt was very hot. Is that normal? Should t


The belt heats up due to the friction, as well as being in contact with the shaft of a hot motor. It is normal. ... Kenmore Progressive 35922 Bagged Upright Vacuum

Kenmore Elegance Upright Bagged Vacuum Belt Broken and Smelling


It sounds like the brushroll has caused your belt problem and will be the cause of your burning smell as well. What commonly occurs is that carpet fiber,hair,string, thread,etc got wound around the brushroll and some will get caught in the end caps w ... Kenmore 34612 Bagged Upright Vacuum

Replace motor hoover windtunnel - Hoover U6476-910 WindTunnel Upright Vacuum Cleaner Bagged Vacuum


... Hoover U6476-910 WindTunnel Upright Vacuum Cleaner Bagged Vacuum

Hoover windtunnel red light stays on - Hoover U6476-910 WindTunnel Upright Vacuum Cleaner Bagged Vacuum


... Hoover U6476-910 WindTunnel Upright Vacuum Cleaner Bagged Vacuum

Windtunnel vacuum brush won't turn - Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum


... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

My old bissell 3510 upright vacuum seems to have no suction into the bag...I replaced a broken belt several days ago, and now the vacuum picks up debris, but seems to just collect it behind a wheel..The bag does not "puff out" like it used to...How can I fix this??


... Bissell 3510 PowerPartner Upright Vacuum

I have a Eureka Boss Power Plus and the beater bar is rolling, the belt is turning, but after vacuuming up around the litter box (not a lot of litter), when I turn the vacuum off, the litter, or even household dirt, falls out. When I hold the vacuum back to turn it off so that it doesn't fall on the floor, it's sitting in the cubby where the wheels are. The bag is empty, the hose is not plugged, the hose is securely fitted on both ends of the unit. This vacuum was purchased in July and is being


Even though the brush is spinning, you probably need to replace the belt because it is s ... Eureka Vacuums

Can you help with this Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum ... hard to move on carpet


... Vacuums

Bissell Powerf DJ68-00161C Upright Bag Vacuum will not power on. I did rinse out the bag compartment but it should be dry now. I use the Style 7 bag & belt. This is the first time it will not power on.


Hmm, you really should not ever rinse out your vacuum unless you have a model that specifically states it is called for. If you must, then use only a slightly damp sponge or cloth. There are so many ways water can have ruined your motor. Let the whol ... Bissell 3522 PowerForce Bagged Upright Vacuum

Hello, I have a problem with my Eureka Powerline bagged upright vacuum. It has a 12 amp motor and is model #4352, Type D. It was probably bought new in 1998. My problem is, while vacuuming today the motor seemed to slow down all of the sudden and then began smelling like burning rubber. I shut the vacuum off to check for blockages but could not find anything blocked. When I then turned it on again it runs but seems to only be running at 1/2 the motor speed and still has the rubber buring smell.


It sounds like a rubber sealing in the motor has come loose and is being constantly rubbed against the walls of the motor with would cause the smell and loss of motor speed caused by the fricton of rubber against the rod so if you can get to the moto ... Vacuums

Vacuum dead I have oreck XLx2 bagged upright - the belt ,plug and cord have been replaced - has been working great - now went to plug it in and it does not work - the light goes on in the on/off switch so power is working but vacuum is dead - any suggestions


If the cord coming from the bottom up to the handle is loose, and is a plug, push it in. If that doesn't help. then could be a problem with the motor. One other thing to check is inside the handle, maybe a wire came loose. ... Oreck XL2200 Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1104 seconds