Having problems with your Hoover U5450-900 Windtunnel Supreme Bagged Upright Vacuum ?
The On Off Switch has stopped working - loose in the fitting - If you jiggle a bit some times starts!
No other way but to open to access the switch and first of all use a good switch cleaner to try if the contacts gets clean . check the continuity and repeat. Refitted it tight so that when you switch the lever moves to contact.If not there is no way but to replace the switch.
Repair Help & Product Troubleshooting for Hoover U5450-900 Windtunnel Supreme Bagged Upright Vacuum
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
The On Off Switch has stopped working - loose in the fitting - If you jiggle a bit some times starts!
No other way but to open to access the switch and first of all use a good switch cleaner to try if the contacts gets clean . check the continuity and repeat. Refitted it tight so that when you switch the lever moves to contact.If not there is no way ... Hoover U5450-900 Windtunnel Supreme Bagged Upright Vacuum
My Sebo automatic X1 has stopped working Every time I attempt to switch it on the only thing that happens is the bag and roller warning lights flash briefly. This suggests the power is ok but the Sebo doesn't start. Any suggestions?
Check for clogs, and also check the brush rollers' belt.Really, i think you should take it to a vacuum shop and have it inspected for problems ... Sebo Automatic X1 Bagged Upright Vacuum
Faithful Sebo X1 upright, about 12 years old, stopped working today. I replaced old with new dust bag, checked all dust paths were clear, checked main brush was clear/clean, and drive spindle rotated OK with fingers. When power switched on, the two red indicators briefly flash on then off, but nothing more happens, motor does not start - even with power reaching machine. Tried removing all consumables, refitting and turning on a few times to reset, no joy. Removed base cover, both belts were i
At 12 years, this vacuum has had a good long life. I suspect the motor is shot, but it could be due to faulty wiring and connections. A bad switch, break in the power cord, and worn brushes in the motor are other causes.\015\012I recommend ta ... Sebo Automatic X1 Bagged Upright Vacuum
My handle won't go back up after an extended vacuuming session during which I used the hand/broom/animal hair attachments several times, thus pulling the hose out/putting it back in, starting/ stopping, and suddenly no matter what I do short of forcing it (and even if I try forcing it a bit) I can't raise the handle to put it away.
Do you know what model number Dyson you have? Is it the ball style one? Just find a similar product here on this page and let me know what model number is closest: ... Dyson Vacuums
My scooba when switched on starts to spray water then spins round faster than normal then starts to go backwards quite quickly then stops then continues to reverse more then stops & with the nor
... iRobot 5800 Scooba Vacuum
Press the power button on - good got a green light (new battery) press the clean button - got a green light iRobot runs for a couple of seconds and stops, then starts, then stops. After two or three times I now have a red light on for the Status. All of the wheels seem to be clean. I used compressed air to clean the underside. But still have the start stop problem.
How many times does the red light blink before it pauses? ... iRobot Roomba Discovery SE Bagless Robotic Vacuum
My Dyson DC07 vacuum started to run slower after being on for a little while and then would run normally again. I have switched on today and it has just stopped. When I push the start button, on occasions it almost starts and then doesn't. I am wondering if there is a problem with the switch and if so how can it be fixed? Thankyou.
The motor running slower was the motor starting to burn out. The "almost start" is the brushes making intermittent contact with the armature in the motor. \015\012\015\012Your machine needs a new motor Pam. ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
Good evening, I have a Xio Z1010 electrolux vaacum cleaner and I hope you'll be able to give me some advice. The vacuum cannot be started. Last time it started for a few seconds and stopped suddenly. Something similar happened long time ago but that was due to overheating. Once cooled down in few hours it would start again. It is not the case now after 24 hours. Could you give me any idea what could be the reason? Your help would be much appreciated. Adorian
... Electrolux Vacuums
My dyson dc 16 hand held vacume stops & starts while in use, each time you pull the trigger it will start again but then stops after a short while untill i pull the trigger again.
Cutting out can be due to a few things , motor overheating due to dirty filter, Faulty mains cable or plug..sealed type also..Faulty Switch/trigger.May need to seek pro help to fix. ... Vacuums
Two weeks ago, my 4150 roomba stopped during running and sounds "ehh". every time i hit the clean button it sounds "ehh" and doe'snt work. at the first time it did it ,i have cleaned the sensors then it start moving forward and backward until it stopped . from now on it only sounds "ehh".
EHH sound:-------\015\012Cliff sensors are dirty or need repair.Try cleaning the sensors and check.If still the same problem then the sensors needs to be rechecked and its connections has to be replaced.\015\012You can try this opt ... iRobot 4150 Roomba Vacuum
My dyson won't stay on. I push the red power button and it begins to start but as soon as I stop pushing it, it stops. It will only work if I keep pushing down the start button the whole time I'm using it. HELP!!! I love my vacuum!
... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
My lux 7000 has a new bag but when i start to use it with the power unit or without the unit shut's it self off i can reset the lites or the motor if you will by clicking the on off switch 4or 5 times and i'm ready to go again untill you start to work and off it goes you can repeat the switch thing as long as u want, it just won't let u vacuum ,it turn's it self off .I blew it all out but found nothing in it. if u don't try to vacuum it will run as long as u want to listen to it. Can you
Have you replace the afterfilter? It may also cause this if rather dirty. It's located under the tool caddy/air diffuser on the back half of the machine.\015\012Try this: Disconnect hose, turn on vacuum. Does it continue running? If so, pl ... Electrolux Lux 7000 Bagged Canister Vacuum
My roomba backs away from docking station then starts to go then stops and spin left then stops and spins right after a few times stops and beeps many beeps. What is the problem
It sounds like the 9-beep error. You can fix it by buying a repair kit from www.eesolutions.ca. I fixed mine in about an hour and a half. ... iRobot Roomba 530 Robotic Vacuum
Problem starting Sometimes will not start at all. Sometimes will do a quick start and stop. Other times it starts and runs fine????
This can happen if you have an intermittent short in your cord. Try plugging it in and then wiggling the cord around where it goes into the body of the vacuum with the switch set to "on." (If you're not sure whether it's on or off, just click it back ... Dyson DC07 Bagless Upright Cyclonic Vacuum
Shark Euro-pro EP621 Bagless Upright Vacuum. Q regarding the brush not spinning / after troubleshooting and taking actions listed below, it now spinning for a few secs, but then stopping. Already removed hair, strings, etc. Checked that belt is aligned properly, checked that small wheel that turns belt is working (spins fine when belt removed. Oiled the turning parts a bit, that made it spin better, but still stops. It turns about 3-4 seconds then stops. If I switch it off and on again, I get ag
... Euro-Pro EP621 Bagless Upright Vacuum
Hoover on off switch won't turn off. I have to unplug the vacuum to stop it. I have dismantled the handle and now I can't get the inditation in the handle to fit over the little silver knob. I saw there was an on/off switch under the handle that is controlled by a piece of the handle. #1 question for the manufacturer is why don't they put the switch on the outside instead of having gimicks that turn it on and off... arghhhhhhhh
Don't know what model you have, but sounds like you will need to replace the switch. As far as your question, you will have to contact the manufacture for an answer. We only provide solutions to your problem and a model number would have helped. ... Vacuums
Vitamix 5000 stopped working. It stops working each time I use it; while blending I first smell a burning smell and then blender stops and will not start again. After sitting overnight it works again next morning and repeat same process. Any ideas how to repair?
It has an internal thermal shutdown. Let it sit for a while and it will reset itself. You can expedite by putting the motor base in the freezer for a few minutes, or by blowing a hair dryer into the base of the motor. ... Vacuums
My machine (Hoover Wind Tunnel - bagless) is only 1 yr. old. The agitator brush doesn't turn all the time. I know it's not supposed to turn when in the upright position. However, it only seems to work when I have the setting on high. When I stop, but have not put the machine in the upright position, it stops again and then slowly starts moving. Could the V-belt be worn out already? In the owner's manual it states that this belt is not normally replaced. The exact same thing happened with my old
Sounds like you should do two things:\015\0121- Remove and clean the beater brush of all debris as best you can. At the end of the brush you will see a hard rubber piece, at both ends, that holds it in place in the body of the vacuum.\015\012Add som ... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum
My iRobot Roomba 560 starts spinning sporadically during the cleaning, and after over 3 minutes it complete stops and beeps 9 times. It is necessary to turn it on until it decides to work properly, and keep waiting for the next time the same failure will occur. I tried to reset it, and I have all the dust removed including from the bumper and sensors.
It's the bumper. Blow it out with compressed air and clean the cliff sensors. If you still get the 9-beep error, call support. ... iRobot Roomba 560 Robotic Vacuum
Panasonic NN-SD776S microwave Start button stopped working. I know, the first thought is a bad door switch because "everyone knows a microwave should not turn on if the door is open." I am experienced with electronics, but even the timer won't start at all. Funny thing is, I had this exact model do this exact thing just over 2 years ago - troubleshot all the hardware until I was lost, finally bought a new one from Costco (June 4/08). And now 2 years later this one craps out - a 2 year timer
Hello Aaron,Since your microwave is controlled by logic, and the start button / timer portion is not working, I would start troubleshooting the power supply.Get a look at the integrated circuits that are on the circuit board, ... Vacuums
I have a DC 21 Dysonstowaway. Lately it cuts out a LOT, when vacumning . I press the start switch on the head, goes for 5 sec. Stops, goes, stops etc. How frustrating !! What can I do ?
Sounds like a loose power connection someplace on the machine.\015\012Probably needs to be looked at by an experienced repairperson.\015\012 ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
Electrolux Centralux I have a Electrolux Centralux. When I plug the hose in at one of the wall outlets the motor will not start. If I go to the motor and slap the unit it will start.....then...it will not stop unless I unplug the power cord to the motor. If I plug the power cord back in, the unit will not restart until I slap the motor unit again. The unit has only been used 20 - 30 times. Any suggestions?? Thanks, Bruce
I dont know if you had your unit looked at yet but it sounds like the Power module is going. I repair the machines so I know some of the work. ... Electrolux Centralux Vacuum
I have cleaned & cleaned this thing! It runs for about 2 mins & stops, says "Clean Brushes"! and now it's very noticeable it's not picking up well... but is picking up a bit. I take the dust bin out, and the brushes spin.... and it has much more power.... and is very clear it is working! But it's useless without the dust bin! LOL It's only 9 months old.... called customer service, but it was the one time it worked just fine! Of course, I thought I'd stop here first before calling again! Than
Ok, this is a "Brush Height Adjustment" issue. It will probably work great on a hard surface but on carpet the brushes bog. If you've taken the unit apart already...Sorry....do it again. When you do, you'll see a String which allows the brushes to " ... iRobot Roomba 560 Robotic Vacuum
Hi. DC14 not running. Repeated pressing of the switch occasionally produces a split second whirr from the motor. I had been picking up plaster dust for some time but stopping regularly to clear out filters and 'the little tubes.' The switch is fine. I cannot see how to get at the motor. Thanks , Chris
Hi again. I finally figured out access to the motor. One of the brushes was burnt and broken. I have ordered a replacement set and cleaned up the comutator ( spelling ?). Thanks, Chris ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum
CLEANER SWITCHES ITSELF OFF AFTER A FEW MINUTES USE. IF LEFT FOR SOME TIME, IT WILL START AGAIN FINE, THEN AFTER A FEW MINUTES MORE USE , IT WILL SWITCH OFF AGAIN.
Check all filters, if they can be washed do so, if not clean or replace. next check for a clog in the machine and in the hoses. the machine as a thermal device that if it senses an overload or getting to hot, the machine will shut itself off for safe ... Vacuums