Having problems with your Hoover U5471-900 Bagged Vacuum ?
I need a replacement agitator brush and have been
\015 I need a replacement agitator brush for my Hoover U5471-900 Bagged vacuum and have been unable to find one.\015
Check out Vacpartswarehouse.com
Repair Help & Product Troubleshooting for Hoover U5471-900 Bagged Vacuum
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
I need to know how to replace a agitator brush for a Hoover Fusion model U5180 900. I was given the vacuum, but without the manuals, so I have no instruction on how to replace the brush. I have already purchased the new brush. Thank you for your help
Please use the following link.\015\012http://www.hoover.com/pdfs/manuals/U5180900.pdf ... Hoover Fusion Plus Cyclonic Upright Vacuum Vacuum
I need a replacement agitator brush and have been
Check out Vacpartswarehouse.com ... Hoover U5471-900 Bagged Vacuum
Agitator brush roll needs replacement
To change the beater bar you would need to open up from the bottom.To get the parts you would need to produce the model and serial numbers to your local hoover dealeror cheak on the internet for your closet dealer and order the part.There not to bad ... Hoover U8143-900 Upright Vacuum
Hoover Windtunnel U5750-900 Agitator brush is weak. It turns fine if I tilt the vacuum back, but it slows to almost 1/4 speed when it touches carpet, even on the highest carpet setting. I've replaced the agitator belt twice. The brush used to turn powerfully even on the lowest (Hard Floor) setting. Ideas? I should probably lube the agitator brush ball bearings, and re-check the belt, but, other than that, I'm stumped.
... Hoover U5750-900 WindTunnel Bagless Upright Vacuum
Need to replace motor brushes on Kenmore canister vacuum 116.25914503 - Getting lots of arcing at brush ends. Need tear-down steps to get at the brushes.
If you can see the arcing you are likely in the motor housing. The brushes are specific to the motor depending on RPM. Most brushes and motors in Sears units are supplied by AMTEK Lamb. The color on the plastic housing and stamped model # on motor w ... Vacuums
Hoover Upright U8185-900 agitator brush stopped working...took hood off...PCB display bridge fried...ordered new one & installed...that burned up in 15 seconds...ordered another PCB and new agitator motor...and since I was in there every **** thing else replaced also...took whole thing apart and cleanded even tho agitator brush was not jammed...put all back together...**** thing just sits there with red led lights displayed...this is ridiculous
... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum
Dyson DC07 brush roller is worn and won't make contact with the carpet anymore. I need to replace the brush roller but don't know how...HELP?
Buy the brush over the web etc..\015\012\015\012To take the brush out \015\0121 - Take the outer covering - uese a penny to turn the yellow srews\015\012\015\0122 - Slide the black brush out from the assembly - Try the n ... Dyson DC07 Allergy Blue/Turquoise Bagless Upright Cyclonic Vacuum
Kirby Vacuum Hi Bruce, In my opinion, yes the Kirby would be worth it, as long as you are not replacing the motor. The switch would be the most expensive part besides the motor that would need to be replaced. The switch costs USD 49.99, the cord is roughly $39.99, and the carbon brushes are $29.99. I can easily walk you through any of these repairs should you need help. Kirby's are great vacuum cleaners, that usually last 30+ years. Brand new these machines sell in the US for $1600 or more,
You can get better prices from Goodvac.com ... Kirby Generation 3 Bagged Upright Vacuum
Dyson DC07 I actually need to locate and replace the brush as it split on one end. Looks like I need to pull the belt off to do that. Might as well replace the belt while I'm at it.
Hi.\015\012\015\012Depending on wether your machine has A clutch fitted will decide how easy this job will be.\015\012\015\012The non clutched model is very simple turn the 3 plastic screws on sole plate to unlock position lif ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum
My bissell brush band has come off and wont stay on thus the brush will not turn, there is also a black arm type thing on a spring inside (on both sides) on the pump belt side it has broken - the side where the brush belt is, help im searching for parts and a way to fix it but im getting no joy, incidentley the brush belt thickness looks way to thick for the small thickness for the brush belt cog (?) to stay on........am i missing something? so i need to get the arm thing replaced plus find a
... Bissell ProHeat Deep Cleaner Upright Vacuum
Dirt devil vacuum cleaner--trouble vacuuming dirt and pet hair on carpeting --is the problem with the spinning brush which contacts the floor, not contacting the carpeting?? I thought (when I bought this vacuum) that the aforementioned brush was adjustable to various heights of carpeting. Sometimes, it seems like nothing is being vacuumed up --unless I have just put a new bag on the vacuum... Do I need or can I replace the spinning brush on the bottom of the vacuum so it kicks up and vacuums
Try replacing the belt. Rubber belts stretch out after about a year. ... Dirt Devil CE6100 Featherlite Upright Vacuum
Need replacement brushes steam buggy model no ek 8005
... Tristar SB Steam Buggy Vacuum
I need replacement carbon brushes for the motor. I haven't been able to find a source.
Try looking for a power tool repair shop, they usually have some brushes and can order more. I have put Hoover brushes in my Shop-Vac.\015\012 Look for some that are close to matching,( spring size,spring length, brush length). If the brushe ... Hoover Portapower C2094 Bagged Canister Vacuum
My Model is a U5465-900 - I need to replace the agitator housing.
I don't seem to be able to find a site with entire replacement parts list. Or a cross reference to the U5465-900 model. It has a 15" agitator. The housing has been "rubbed" through at one side of the agitator and is no longer capable of contain ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum
Bissell lift off vacuum about 4yrs old. Extremely noisy. OK until before Christmas but getting worse every time it's used. Washable filters washed, HEPA filter replaced. brush bar cleaned of every scrap, hose empty,everything that can be cleared has been. Noise high pitched, screeching and can only bear to use it for a few seconds at a time. Suction OK. Mine is so loud I can't use it very long-high pitch screech. Can this be fixed or does the whole vacuum need to be replaced? It still cleans gr
Sounds like a bad motor. Could be either foot motor or main motor either way cost will be more than half of the unit. ... Bissell Lift-Off(R) Revolution(R) Turbo Upright Vacuum
Schematics I went to replace the belt, and when I put it back on I noticed the silver pulley that the brush belt goes on has came unattached from the red piece by the motor belt. It is one peice. I can order a new pump, but I need the schematics so I can replace the pump. http://www.vacuums24x7.com/bistclpa.html How can I enlarge this so i can read it?
Well you can right click the picture and save it to your desktop, I did it, but it was alittle blurry. But if this doesn't work for you, post me your email addy and I can send you a better picture. But take the top off, there are 6 screws, 3 on ea ... Bissell 8910 ProHeat Clear View Upright Vacuum
Need to replace belt for brush. Brush isn't moving
Hi there SmartAlec from NelsonVacuums.com.au here. If you are in Australia i can help you get this part. Just go to our home page and use the contact us link. I actually just ordered some of these belts so will have them in a day or so. Regards Alec ... Bissell Powersteamer 1694 Upright Vacuum
I have a dyson dc14 how do i repair my vacum? i need to try to replace the brush bar motor or something so that i can get the brush bar to work again.i hope you can help me out
Brushbar not spinning:--\015\012Ensure brush control is set on carpets mode. Note: brushbar will only spin when\015\012the handle is reclined.\015\012To get user manual for your vacuum please click on the link mentioned below\015\012 ... Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum
I caught a shoe lace in my Dyson DC17; pulled it free, opened the brush/roller area and cleaned everything but the brush still won't work. Read somewhere that there is re-set button but the only one I found was to switch between the brush / sweep functions. Is there a fuse / connection / part that may need to be replaced?
I don't believe so. Keep trying the reset button. Sometimes the reset sticks. Hope this helps. ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
I have a dyson dc all floors and I need a new bottom brush, will I be able to replace it myself without breaking any plastic parts,if I order the brush online?
I would say to take it into a shop. Don't try it yourself Dysons arent any vacuum you can just go into target and buy for 50 bucks. there not made to just be taken apart. ... Dyson Vacuums
Hi,My agitator brush won't run on my hoover S3590, I changed the belt, that didn't work. I don't see a possible cause in my book except replacing the belt. I think there could be a short, the brush will come on sometimes when pulling back and slightly lifting. Any ideas would be great and can I fix it myself? Thank you for any help, Bobbie
Hi Bobbie\015\012Take apart the electro floor head if you can and inspect inside - it may well be that there's clogged dust preventing the brush from turning and also check both sides of the actual beater bar as thread and tangled hair can often lead ... Hoover S3590 Bagged Canister Vacuum
I need please a belt for the brushes the larger one but may be better to replace the smaller one as well. I can see how to replace the small one very easily but not sure how to get the new one onto the end of the big sprocket. Please can you help I have the vac disassembled ok just waiting to get the belt to reassemble it. thank you Colin White SEBO AUTOMATIX X1
As you know, there are two belts - the pulley device between the motor and the brush roller is the sensor that measures the drag on the brushes and operates the automatic height adjuster to maintain constant drag. To the left of that double pul ... Sebo Automatic X1 Bagged Upright Vacuum
Do i need to do anything special when replacing the brushes in a lamb ametek 117500 motor? It looks like I can just remove the old brushes and insert the new ones. Is it this simple? Will the motor work again? Thanks
Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=758676\015\012Generic problem for all Vacuums\015\012Do I need to do\015\012Posted by edkraynak on Jul ... Vacuums
Bearing on end of brush froze causing belt to break. I need to replace the brush and belt. Are there other belts in/on this model?
Hi there. there is a belt in the unit. the owners manual here will give a good guide on how to replace the unit.the ... Eureka 3041BZ Upright Vacuum
I have a Hoover SteamVac, Model F5906-900 and the brushes won't spin. It's like something is froze up inside. I have read where the Brush Turbine might need to be replaced. Can you tell me where I can find the schematics or an internal diagram of this model so that I can take it apart. Or maybe you might have another suggestion. Thank you Pauline Newman
\015\012Hello,\015\012\015\012This is most likely the reason the for the brushes stop spinning. I've written a very detailed repair guide on how to diagnosis this problem. This will walk you through step by step with pictures, an ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum