Having problems with your Hoover U5491-900 Bagged Upright Vacuum ?

My hoover U5491-900 is not picking up any dirt . very little suction. i clean every surface of the vacumm. there is nothing stuck any where . and its still not working

Answers :

Repair Help & Product Troubleshooting for Hoover U5491-900 Bagged Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My hoover U5491-900 is not picking up any dirt . very little suction. i clean every surface of the vacumm. there is nothing stuck any where . and its still not working

... Hoover U5491-900 Bagged Upright Vacuum

Water and cleaner not coming out, The machine is only 6m old and was working fine, I have cleaned every where I can to see if there was a blockage but nothing is working. The heater is working, there is a suction but the water and soap will not realease when triger is pulled. it will not work on on the tool spay.

Check the complede length of the hose. You may find a crimp in the most inconvenient place. You say you cleaned everything ... can you blow through the hose where the cleaner comes out? (don't drink anything!) ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Hi all---I have a Dirt Devil 091020V. there was a problem with the wand where it was the only thing sucking even when it was stuck in the tube it would ****--but nothing from the vacuum end--the diverter was stuck closed I took it apart and found something stuck but in the meantime the torsion spring [I think} fell out and I don't know where it goes--so now only the vacuum works --not the overhead cleaner part.. is there a digram somewhere that can tell me where it goes--I think it might b

... Vacuums

Only every 10 or so stitches holds. Probably a tension problem, but I don't have a manual and I've tried every setting and nothing seems to work.

A sewing machine should catch and tie the threads at any thread tension. If it's not tying and you're sure it's threaded correctly then it's out of time.Timing a sewing machine is not difficult, but the point where you adjust the timing i ... Vacuums

My seb0 automatic x1 roller have stopped working . there is nothing stuck in it . the suction part is working perfectly. can you help please?

\015\012Almost certainly you've got a broken drive belt. This machine has two toothed belts and it makes sense to change both while you're at it. Incidentally, this is a job you shouldn't have to do very often - Sebo belts usually last at ... Sebo Automatic X1 Bagged Upright Vacuum

Kenmore Progressive Cannister Vacumm, Powermate Floor Unit quit working. I replaced the reset switch but still nothing. Light doesn't work either.

Is it working on other mode?.Or its not having any power at all?.\015\012\015\012Select a switch position o the handle.OFF MODE.\015\012\015\012FLOOR:-- turns on the canister motor only. \015\012CARPET :-- turns on both the canister and the Power ma ... Kenmore 25512/ 25513 Progressive Canister Vacuum

Last year my wife and I bought a new Dirt Devil Reaction All Surface vaccuum cleaner to replace the older Platinum Force. After using it a couple of times the new one gets clogged with dog hair easily and shuts down. I cleaned it out completely including the hepa filter but it will not handle the dog hair. The old one never had a problem and still works. We went back to using the old vaccuum cleaner because we can not find the receipt and had not registered the new one and are stuck with a new 1

Greetings jettin_us,\015\012\015\012Normally you can contact the store you purchased the unit at, and if you paid with anything other than cash, they may be able to retrieve your receipt for you. \015\012\015\012Once you get t ... Vacuums

My electrolux ZTI7671 turbo nozzle has stopped working, nothing is stuck but the turbine has become very stiff and isnt rotating with the force of the suction. what shall i do?

... Electrolux Vacuums

My kenmore vacuum model 116.36933502. It has no suction. I have cleaned out every spot,taken off the back and still nothing. The motor runs but doesnt seem to be at full power. The agitator brush works. When it broke i seemed to smell something and since it has no belt. Does this possibly have to motors?

... Kenmore Progressive Bagless Upright with Inteli-Clean SystemVacuum

Hooked everything up per directions. I plugged it in to the closest electrical outlet and nothing happened. The lights did not light up, the connected wall control and sensors leds do not light up. It appears the unit doesn't have power. The electrical outlet socket is fine as everything else I plug into it works fine. I have tried every other electrical outlet available. The unit won't power on from any outlet, and all of those outlets run other things, like power tools an refrigerators

Dear Davehibshman,Firstly; dismantle the plug and replace the fuse with the same rating as the one you have just taken out. Replace the plug cover, put the plug into the socket and try again. If this doesnt work, there may be a problem wi ... Vacuums

I have a littermaid elite automatic litter disposal system. It stopped cycling and both lights are flashing. Nothing is stuck, it just made several passes at some point overnight without successfully getting to the receptacle due to heavy litter. The box was clear and moving before we went to bed. This morning the lights were flashing. I unplugged, emptied, etc and it will not work. what now? It does not have the reset button at the receptacle button that the old models did. Is there one?

... Vacuums

My eureka enviro steamer model 370 water reserve cap is just plain stuck. I've had several people try to unscrew it but nothing has worked. Can you please help!

... Vacuums

The hose works great, but the head of the vaccuum does not pick up anything !!! I checked every opening that may have been clogged, but nothing came up. When I hold my hand under the brush/roller, it seems to be putting out more air than intaking air. Particles "dance" on the carpet, but don't get "sucked up" into the vaccuum ? I have had the vaccuum only 1 year, so the brushes should not be a problem. I changed the bag, and checked the belt. The belt and brushes seem to be OK. ?

Hi there,Uprights are notorious for debris forming clogs when changing direction. The 90 degree turn where the base suction goes up. Have a closer look . You may need to pull the base plate off to access the blockage.Best reg ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Loud noise I have a brand new Dyson and it is great on all my floors except one of my area rugs when it starts making this really loud vibrating noise. I am not sure why - nothing is stuck in the roller or vacuum and it doesn't make it on any of my other rugs. Also it is really hard to push whereas all the other floors it just glides. I don't want to return it but I also don't want to hear this sound every time I vacuum.

This is the clutch as it jams up in the brush. Usually happens with rugs that are not secured to the floor. ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

I have a mile tt2000 that works fine up to 1300W but if I crank it up higher the motor decreases and increases speed every couple of seconds. I have changed the bag and filters and done the usual cheCks for blockages but can find nothing amiss. Unusually when it is running and I block the intake it will run at full power but as soon as I clear it the motor "hunts" again. Any ideas.

... Miele Cat & Dog 326i Bagged Canister Vacuum

My electrolux ZTI7671 turbo nozzle has stopped working, nothing is stuck but the turbine has become very stiff and isnt rotating with the force of the suction. what shall i do?

... Electrolux Vacuums

Our kenmore progressive model #11634922 was working fine today. And then - it's not. Plugged in - nothing is working on it. We let it cool down (though it didn't seem hot). Still nothing - no light, no motor. Tried it in some other plugs that we know are functioning well - and still nothing. Any idea what might be wrong with it? It's six years old but doesn't get heavy use. Thanks so much ~ Susan Golden

Hi, it could be a number of things, cord may be bad as well as a problem with the motor. There also is a fuse that could have blown. If you go to sears.com, click on parts, put in your model number, when the page loads, click on the first link ... Kenmore Vacuums

I have a Kenmore DuraPower Dual Cyclone Action 12 Amp that just randomly stopped right in the middle of vacuuming. I assumed the plug had come out of the wall so I went to check and this wasn't the issue. I tried multiple outlets and that wasn't the issue. I made sure nothing was stuck and there is nothing stuck. Nothing happens when I press the red "ON" button. What could this be? Thanks!

... Kenmore Vacuums

Kenmore progressive model#116.21612001 worked fine then nothing!

... Kenmore 23313 Whispertone Bagged Canister Vacuum

I have a Juki serger mo-634de that I am borrowing from my sister in law. She doesn't have the manual, but just got it back from the shop in good working order. I have threaded the machine, and when I manually turn the dial, it appears to stitch properly, but when I press on the pedal, nothing happens. No sound from the motor, no movement with the needles, nothing. Help! (c: Power is working, because bulb turns on.

... Vacuums

I set up my ONYX SW2300XS which I recieved as a gift (so no reciept) for the first time today. At first it was working well, I inserted a dvd and it played well. I played with the zoom and the skip buttons on the remote a bit and left it playing while I went a did other things. I came back about halfway thru my movie and wanted to skip scenes but the remote did not work. So I tried the NEXT button on the machine. This did nothing, so I tried the STOP button and that did nothing, the dvd was

Mine does the same thing! The store told me it would play all formatted but it does not! Its junk!! ... Vacuums

Hi I have an electrolux vacumm cleaner, super J model. My problem is that the powerhead only works if the switch is in the off position. vacumm motor works in the on position, opposite of each other. Can anyone help? Model 1401

Looks like there's an interchanged wires in your vacuum. Both the motor and the powerhead must go together. Check it up. Leave themotor wiring connection intact. Just tinker and check the powerheadwiring connection . ... Electrolux UltraLux 2000 Bagged Canister Vacuum

Shampooer I have a rainbow e series and my shampooer is not working. The tubes do not seem to be clogged and it sounds like it is trying to work but we cant get the water to come out. We pull the trigger and nothing no soap, no water, nothing. Can anyone help?

Aqua mates have an o-ringed valve assembly that go bad regularly reccoment having it replaced by local vac shop ... Rainbow E series Canister Wet/Dry Vacuum

I have only had my shark steam mop for about a month and only used it twice. I tried to use it yesterday and it would not work. The green light came on and it worked for maybe ten seconds, then it completely shut off. I tried switching outlets and draining the water but nothing worked. It still doesn't work today either. What do you think is wrong? Does this product have a warranty?

Yes has warranty call Shark/europro. ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum

Water is not being discharged. I have filled the reservoir that holds the carpet cleaner fluid And I have filled the water container. I know how to use the cleaner, it has always worked, But now, no water is being discharged to the carpet. I turn it on, squeeze the trigger, but nothing comes out. The wheel that is suppose to spin (to indicate that water is being discharged) is not spinning. Everything else works. I.e. the suction works, and the hand held accessories work.

That means that the pump belt is worn and it needs to be replaced. You can get a replacement belt and view the manual here:Bissell Pump ... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0621 seconds