Having problems with your Hoover U5720-900 WindTunnel Upright Vacuum ?

Need to replace cord on hoover u5720

\015 Have replacement cord but, can't figure out how to get vacuum apart to replace\015

Answers :

Un do all screws on back of vac replace cord screw back together
Repair Help & Product Troubleshooting for Hoover U5720-900 WindTunnel Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Need to replace cord on hoover u5720

Un do all screws on back of vac replace cord screw back together ... Hoover U5720-900 WindTunnel Upright Vacuum

I need to replace electrical cord on hoover windtunnel UH70120. How do i get the cord reel off? Can i open the cord reel to replace the cord?

... Hoover Company Wind Tunnel U53019 Upright Vacuum

I also have a Hoover upright and I need to replace the electrical cord. I have dimantled the back, where the tools are stored, and the hose. I still cannot find the screws or whatever, to get to the area behind the cord, so I can replace it. I think I will have to take off the bottom too. Has anyone out there tried to do this? It seems crazy. This machine works great so I hope I can also put it back together. Thanks for the help.

Since I do not know your specific model I can only supply you with general instructions. Be aware that most of the time you only need to gain access to the on/off switch to replace the power cord. Also Make sure that you are replacing the existing co ... Vacuums

Need to replace power cord on Hoover windtunnel need wiring help

Without seeing this it would be difficult to describe. I would take it to a vac shop and let him show you. there are no real schematics for the wiring of these units. I usually would cut off the cable with a few inches of insulation to know where to ... Hoover U5399-900 WindTunnel Lite Upright Vacuum

Need to replace power cord on Hoover vacuum.

Remove the dirt container and look for screws. ... Hoover U5753-900 WindTunnel Bagless Upright Vacuum

I need to replace the cord on the beater brush attachement for s3614 hoover powermax.. can't find parts. I was able to pull apart the brusher, but I cannot release the wire to resplice and reconne

... Hoover S3614 Vacuum

I want to open a Hoover S3825 Elite Cyclonic Vacuum to see if I can repair or replace the cord reel assembly. Currently the reel slowly draws the cord back into the canister once it is pulled out. I found the mounting screws under the rear wheels once I removed the hub but I do not know how to remove the rear wheels, everything is plastic. The front screws are under the front caster wheels and I think I need to take a screwdriver and pry off the little cylinder wheel to get to them by rotating

... Vacuums

I have a Hoover Wind-tunnel Vaccum (Model U5433-900) that needs a new power cord. I am looking for step by step directions for replacing the power cord

... Hoover Vacuums

I need to replace the cord on an older Hoover upright, model S660, about 1986 vintage. The cord broke where it enters handle. Handle comes apart easily. Just not sure how to pop the switch out without breaking it. Was looking for a manual online to see parts diagram and/or instruction on disassembly and cant seem to find one for that old of vacuum.

Check ebay. those vacuums are worth fixing. I loved them. they would **** the carpet off of the floor! those cords aren't hard to replace.just remember the way you got the old one out. ... Vacuums

Hoover vacuum power cord replacement u5720 900

... Hoover U5720-900 WindTunnel Upright Vacuum

Hoover Wind Tunnel U6458-900 Self Propel doesn't work - via other expert advice here for other models of Hoover - I'm thinking it is the actuator that needs to be replaced as I can see the cable does not connect to anything on the bottom. My problem is - I can't get the cover off. Been trying for a couple of hours. I removed every screw I can seem to find but something is hold it down. I also am wondering if/when I do eventually get the cover off, would I need to replace the cable when I replac

On some models there are hook/springs that hold the cover of the base snug. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Cord replacement I need to replace a damaged cord (the reel works). How do I get the top off so I can remove the back end? Once I get it off, will I be able to change the cord, or do I need to buy the whole reel assembly? (and thanks for the help - I love this site!)

You will probably have to replace the whole reel cord. Depending on your model, on each side, there is a bar in the middle that will slide off, then the 2 halfs will come apart. They will only slide in one direction. If an older model, there are s ... Electrolux Lux 5500 Canister Vacuum

Hoover u6451 900 how to replace power cord?

... Vacuums

I need to replace the plug in cord on my rowenta iron. I would replace but I paid $130 for iron and my cats have chewed on the cord so I thought it "might" be a simple replacement.

This is the second cat-chewed-a-wire question tonight.\015\012\015\012The only thing to do is to replace the entire cord. You could cut out the chewed section and splice it with **** connectors and electrical tape, but you have a nice iro ... Vacuums

How do I replace a 35 foot cord on my hoover tempo vacuum without adding a risk to burning my house down?

Here is a video that will help you ... Hoover Tempo Widepath Upright Vacuum - Blue

How to replace the cord on a bagged hoover windtunnel

... Hoover Vacuums

Replace a melted Duralit toaster cord that melted from it touching my toaster oven. Need to replace the whole cord. Thanks, Shelley

Cut the bad part off the ac cord then use "****" conector to crimp on a new cord. make sure and note the stripe on the cord and that indicates the neutral wire. the stripe is on the outside of the cord on one of the sides. the stripe is molded on ... Vacuums

Kirby Vacuum Hi Bruce, In my opinion, yes the Kirby would be worth it, as long as you are not replacing the motor. The switch would be the most expensive part besides the motor that would need to be replaced. The switch costs USD 49.99, the cord is roughly $39.99, and the carbon brushes are $29.99. I can easily walk you through any of these repairs should you need help. Kirby's are great vacuum cleaners, that usually last 30+ years. Brand new these machines sell in the US for $1600 or more,

You can get better prices from Goodvac.com ... Kirby Generation 3 Bagged Upright Vacuum

Replace cord on Hoover Hurricane Model HU416

... Hoover U6616-900 WindTunnel Bagless Upright Vacuum

How to replace power cord on Hoover WindTunnel upright vacuum

The aforementioned solutions probably never even attempted this fix on this model. The handle does NOT need to come off. but the 5 screws on the front housing DO: 2 above the light and 3 below it. Then to get the colored housing off you need to acc ... Hoover U6616-900 WindTunnel Bagless Upright Vacuum

I have a very old electrolux canister vacuum that needs the cord winder mecanism with cord replaced. Where can I locate this part?

... Electrolux Vacuums

Need to replace power cord and can't find how to open canister to replace

I had the same problem and could not find the other screws. You need to pry off the power cord retraction button, you will find two more screws under there. It's pretty easy after that!!!! ... Kenmore 22612 Bagged Canister Vacuum

How to remove the bag housing from the handle in order to replace the power cord on a Hoover vacuum U5209-930

... Hoover Vacuums

How to replace Hoover PowerMAX power nozzle cord?

... Hoover Powermax S3601 Bagged Canister Vacuum

I need to replace the cord wrap part that flips up to retain the cord and down to release the cord and can find the part to order one.

You can locate your nearest dealer through the Hoover web site and then call them to order you one. once they have it in you could take the vac to them for the cord hook to install for you. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1123 seconds