Having problems with your Hoover U5720-900 WindTunnel Upright Vacuum ?
Roller bar not working when lower handle
\015 Roller bar does not turn when in vacuuming mode. Once handle is put down to start vacuuming it stops rotating.\015
Repair Help & Product Troubleshooting for Hoover U5720-900 WindTunnel Upright Vacuum
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
Roller bar not working when lower handle
... Hoover U5720-900 WindTunnel Upright Vacuum
Placing the handle of my Dyson DC07 into its upright and locked position causes the beater bar to stop turning. It will not start turning until the handle is first lowered to the working position and the Carpet/Bare knob is moved to the Bare Floor position and then back to the Carpet position. Then the beater bar turns until the handle is placed into the upright position. What might be the problem?
Hi its Darran at Dyson.The brush control is designed to switch the brush bar off automatically when you stand the machine back into the upright position. It is designed this way to protect any delicate floor surfaces when you have the ma ... Dyson DC07 Bagless Upright Cyclonic Vacuum
Hoover U6637-960 the self propel is not not working. When lowering the handle it acts like it would like to work but the roller will not turn. appears to be something to do with the self propel part of the handle . took the screws aout but can not get it apart. Is there another belt of something in there?
This vac has 2 belts. If both self propel and roller not spinning then most likely it is the wide flat belt broken or off. 4 screws on the bottom should gain you access to the belt area. another issue for this model series is a worn pulley on the rol ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum
The model is U5720950, there is no suction at all when I lower the handle to vacuum. But when I use the parts, they work properly. I cleared the roller and put everything back in place. Did I misplace something? Can I fix it myself without taking it to service?
... Hoover U5720-900 WindTunnel Upright Vacuum
I have just purchased two (2) Electrolux Nimble vacuum cleaners. Not one, but both, straight out of the box, the beater bars will not run. It turns on, select carpet, and lower the handle, the red light to check beater bar/or filter lights up. You can reset the light by unplugging the unit, then plugging it back in, but with same results. Now the kicker, if you take out the handle, select carpet, lower the body by the carry handle, it will run and operate correctly, however, as soon as you r
I have a Dyson 15 "the ball". The beater bar will only rotate if the vacuum is engaged and the handle at a high angle. The bar stops when I drop the handle to a lower position. The condition is repeatable. Can you provide part and repair instructions?
If air is leaking in somewhere, you will not have any suction.\015\012\015\012\015\012Also there are some possibilities that has to be checked to confirm the fault.The problem is minor but the possibilities are too much for this pa ... Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum
I have 2 Hoover Wind Tunnel-self propelled bagged vacuums-U6433-900 model.The roller bar does not agitate, the self propelled feature does not work and, in general, the vacuum is not performing well. I have replaced the roller bar, the v belt and the wide belt. The filters have been replaced and it has a new bag. I have had both of these since 2004 and they were fairly expensive $200 each) but if the repairs are prohibitive, I might as well get new vacuums. Suggestions? I just spent $100 for bel
The Hoover WindTunnel self propelled is a machine that we see in our retail stores (Vacuums Unlimited) constantly. The benefit of having a supposed "self-propelled" machine wears of quickly after the numerous time you will need to take this machine ... Hoover Vacuums
Had my dyson root cyclone for about 4 years now, and in the last year it's had a few problems. About 4 months ago it started to make this awful grinding sound when the roller bar was engaged and I took it to a repair shop and they said it was the roller bar itself. The shop replaced the part and it worked fine for a couple of months and then it started to make the grinding noise again. I tried the clutch reset suggestion (turn it on its side and turn the carpet/bare floor switch slowly back and
Bdepends how much thay charged you for a roller brush because you can buy a good vac for about 100 pounds with a 12 month guarentee so its up to you ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
The power brush floor rug attachment on my Eureka 6997 A Oxygen Canister Vacuum goes on an off as I use it. I replaced the The power cord from the handle has 2 plug in connections: 1 at the handle / upper wand 1 at the lower wand top of the power brush attachment I replaced the entire wand assembly and it worked great for a year or so and now it's doing the same thing again. I was told to keep the power switch on the handle set to off when connecting the power brush attachment or it will bu
This is from the prongs not making a good connection causing an arch inside the plugg causing what looks like rust on the plugg. I would try snugging up the connection by squeezing the female section to get a better connection on the prongs when it i ... Vacuums
Hoover U5344-950 My Hoover vacuum is a nightmare! I have had nothing but problems with it since day 1. The powerhead stops working if you try to lower the handle to vacuum. I took it in to be serviced and was told it sat on the shelf for too long in the store and it warped the belt...so it was replaced. Got it home, it worked the first time I tried it, then went right back to no powerhead working and as a bonus it is giving off a nasty smell like it is going to blow up! It now gets really hot to
... Hoover U5344-900 WidePath Vacuum
Beater bar on Dyson upright won't turn when handle is lowered
I have finally fixed my sister's dyson dc 15 beater bar problem. It was just 2 tiny broken wires connect to circuit board lead to the beater bar. The wires broke where they go through the black rubber gommet. You need a torx ... Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum
My Dyson DC 28 won't lower. You're supposed to step on the front and lower the handle. It won't work. What's up?
Hi its Darran at Dyson.So that we can help, please call our Helpline on 1866MYDYSON. Kind regardsDarran Dyson Customer Service ... Dyson DC28 Animal Bagless Upright Vacuum
My dc-15 bush bar will not work - Dyson 909592-05 DC-15 Roller Brush Beater Bar
Head motor blown, will have to take it to your nearest good hoover repair centre should cost around 49 dyson will charge 73 ... Dyson 909592-05 DC-15 Roller Brush Beater Bar
My beater bar will not spin when the handle is lowered? But there's suction thru the hose when the handles upright
I had the same problem. I read, earlier today, that one of the "problem solvers" called Dyson. Dyson suggested, with the Dyson upright and plugged in, on a carpet, toggle the "bare floor" / "carpet" knob from bare floor to carpet 5 times, then lay ... Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum
On the bottom of the Fantom Fury where it states:"The United States and Canada utility patent....". Now go to the far right end of this statement (the end opposite the spring, well I have a crack in the plastic which, when toggled, moves the entire plastic underside of the vacuum to move. In other words, I think I need an entire bottom plastic plate. The cracked area also makes the foot lever (which lowers or locks the vacuum handle) not work as the crack makes it impossible to work. I know
Http://www.geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=545424\015\012Generic problem for all Vacuums\015\012On the bottom of the\015\012Posted by c ... Vacuums
I just used my Bissell Proheat, when I heard the vacuum sound get lower and lower then suddenly something "gave" and it got very loud and started emitting a burnt rubber smell. It still worked to put liquid into the carpet; seemed to have trouble getting it out. I checked the tank, filters, belt, and roller and all seemed OK - but when I started up again and looked down I saw sparks in the motor/belt area and shut it down immediately. Any thoughts?
The bearing that is located at the top of the vacuum motor has failed . Because of that the shaft of the motor's rotor is out of position and the pulley attached to it has started rubbing on the other pulleys, giving you that smell. the spark appear ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum
I have a Sanyo Performax 12 amp upright vaccuum. It has lost its suction completely. All hoses and airways are clear, new bag, exhaust works, roller bar works.... but no suction - what might the problem be? thanks, Shelley
... Sanyo Permax SC-A102 Bagged Upright Vacuum
My Eureka Maxima isn't working right. The belt is spinning fine until I lower the handle to start to vacuum and then the belt stops spinning. As soon as I put the handle back in the upright position the belt spins again.
Sounds like belt is worn try changing belt. ... Eureka 4700A Maxima Bagless Upright Vacuum
Roller bar won't work
... Dyson DC25 Bagless Upright Vacuum
The roller wont spin when I lower the handle
Hi its Darran at Dyson.It is possible that the item has caused some damage to the clutch. We would advise following the onilne checks at www.dyson.com and clikcing on the support section.If this doesnt resolve the issue, plea ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
Shark navigator power head will not turn on unless main handle is lowered to the floor
... Dyson Vacuums
How do I open this to check the head??? The roller bar is not working and the cyclone action is not going either
... Fantom Vacums Fantom Wildcat 2100 Upright Vacuum
My roller bar doesn't seem to be working, but I checked the belt and it appears to be fine, but a bit loose. Is this the problem? dial on front to determine heighth is also very loose and does not click anymore like it did a few months ago. Any help would be appreciated. thx.
If the brush roller stalls when it comes into contact withthe carpet, it might be that the tensioner spring has broken off. This is adesign flaw in the Eureka4870. The symptoms are: 1) brush spins until it contacts the carpet then itstalls, 2) the br ... Eureka Smartvac 4870 Bagged Upright Vacuum
Need beater bar / roller belt for GE Walmart Model 106585. Does the Eureka "U" belt work?
Yes, the GE Walmart Upright Vacuums take Eureka "U" Belt. ... GE 106585 Upright Vacuum
We just used our bissell pro heat 25A3/64D9 series and the top half of the handle is not secure. Infact it flies off in my hand as im cleaning the carpet and it almost hit me in the face!!! It just connects to the lower half but there is nothing to keep it secure. If it is not tight the trigger to squirt water doesnt work and I am stopping and starting. It looks like a major design flaw.
I have a replacement pump belt for my Bissell #25A3/64D9\015\012but cannot find the instructions as to how to put a new one on. My son replaced the last belt, and of course he doesn't remember what he did. Is there any way you could please dire ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum