Having problems with your Hoover U5753-900 WindTunnel Bagless Upright Vacuum ?

Hoover windtunnel U5753-900 will not start

\015 Our Hoover Windtunnel U5753-900 will not start. The outlet is fine.\015

Answers :

The most likely problem is the on off switch. but it could also be related to the motor or a connection.But definitely electrical in nature. suggest to take it in for service.
Repair Help & Product Troubleshooting for Hoover U5753-900 WindTunnel Bagless Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Hoover windtunnel U5753-900 will not start


The most likely problem is the on off switch. but it could also be related to the motor or a connection.But definitely electrical in nature. suggest to take it in for service. ... Hoover U5753-900 WindTunnel Bagless Upright Vacuum

Hoover windtunnel will not start - Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum


... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

My Hoover Windtunnel Ultra U6425-900 began shutting off after a few minutes of vacuuming. The time interval became shorter and shorter. If I leave it sit a while, it will start again. This does not happen when I used the attachments - only with the floor brushes. The switch has recently been replaced and the whole vacuum serviced by a Hoover dealer about a year ago. I have been told by a local repair shop(not a Hoover dealer) that it is the motor, there is nothing to do other than replace t


... Hoover Vacuums

Hoover windtunnel will not start i used it for a while tell i switched electrical sockets now it wont stArt


... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

I have a Hoover Windtunnel 2 upright vvacum cleaner. During regular use my wife turned it on and it staarted cleaning, then all of a sudden it stopped and then started again then stopped for good. I unclugged the hose, cleane4de the brushes , blew the main filer and still cannot get it to start. The motor seemed hotter than usual. Can you help me? Lenny Rentz e-mail [email protected]


Actually, if you don't have continuity, then you have an open, not a short. ... Vacuums

Hoover cord will not retract - Hoover U5753-900 WindTunnel Bagless Upright Vacuum


... Hoover U5753-900 WindTunnel Bagless Upright Vacuum

Belt replacement for Hoover U5100-9RM - Hoover U5753-900 WindTunnel Bagless Upright Vacuum


... Hoover U5753-900 WindTunnel Bagless Upright Vacuum

My Hoover windtunnel uh70210 Won't Start


... Vacuums

Hoover windtunnel trys to start but then stops


... Hoover Ultra U6430-900 WindTunnel Bagged Upright Vacuum

Our brush won,t spin can you help? - Hoover U5753-900 WindTunnel Bagless Upright Vacuum


Most likely your brush needs to be removed and cleaned. Clean all debris that might be in the bristles of the brush. You will see a holder for the brush on each end that holds it into the frame of the vacuum. The two holders should turn f ... Hoover U5753-900 WindTunnel Bagless Upright Vacuum

I have the Hoover Windtunnel Bagless U5753 (purpleish one)


You have a broken belt. This is a very common problem. The belt is designed to break if something becomes caught in the brush roll. This is intended to protect the motor from becoming jammed and burning out. The belt is very easy to replace and your ... Hoover U5753-900 WindTunnel Bagless Upright Vacuum

Brush won't turn, belts intact - Hoover U5753-900 WindTunnel Bagless Upright Vacuum


Even though the belt is intact it can still be stretched and not turn the brush. You can get replacement belts here:www.vacbelts.com ... Hoover U5753-900 WindTunnel Bagless Upright Vacuum

Hoover windtunnel u5753-900 roller brush won't move on carpet


Suggest you replace the belt. ... Hoover U5753-900 WindTunnel Bagless Upright Vacuum

Vaccume overheats and shuts down - Hoover U5753-900 WindTunnel Bagless Upright Vacuum


Check your filters. Not changing or cleaning your filters suffocates your motor, so that could be the problem.I suggest checking your local yellow pages for a local vacuum shop and have them fully inspect your vacuum for any clogs. ... Hoover U5753-900 WindTunnel Bagless Upright Vacuum

Hoover U5780-900 Windtunnel a month 1/2 old just started stopping when it is running and wont turn back on for a few hours why?


The motor has a thermal protection sensor on it. So your motor may be going bad, it is pulling to many amps for some reason, could be a clog somewhere or a bad bearing in the motor. ... Hoover U5780-900 Windtunnel Cyclonic Bagless UprightVacuum

Vac runs for about 15 mins. then stops - Hoover U5753-900 WindTunnel Bagless Upright Vacuum


The unit is not getting the proper airflow and the motor is overheating to shut down. \012\012You should check/clean out the filter in the dirt chamber there. If the filter is more than 1 year old, you should replace the filter. ... Hoover U5753-900 WindTunnel Bagless Upright Vacuum

It's not sucking up dirt - Hoover U5753-900 WindTunnel Bagless Upright Vacuum


A couple things to check: Is there suction at the end of the hose if you unplug it from the housing. If you have vacuum to the hose, but not to the brushroll, then you may have a clog in the duct.\015\012\015\012Another check is if the ... Hoover U5753-900 WindTunnel Bagless Upright Vacuum

How to install the torsion spring - Hoover U5753-900 WindTunnel Bagless Upright Vacuum


... Hoover U5753-900 WindTunnel Bagless Upright Vacuum

Hose is clogged - Hoover U5753-900 WindTunnel Bagless Upright Vacuum


Hi,Here is a tip that I wrote about my Bissel but I bet you have the same problemand the hose is clogged...Bissell Bagless Upright Vacuum not work ... Hoover U5753-900 WindTunnel Bagless Upright Vacuum

I can't change belt - Hoover U5753-900 WindTunnel Bagless Upright Vacuum


Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=832643\015\012Generic problem for all Vacuums\015\012I can't change belt\015\012Posted by jaw53t on Jul ... Hoover U5753-900 WindTunnel Bagless Upright Vacuum

Brush on underside not working, please help. - Hoover U5753-900 WindTunnel Bagless Upright Vacuum


Turn the unit over and remove the four screws that retain the bottom plate over the agitator. Remove the bottom plate and see if the belt of off or broken. The belt part number is printed on the data label for the cleaner. ... Hoover U5753-900 WindTunnel Bagless Upright Vacuum

I've had the Hoover Windtunnel for a couple years now. Its starting to smell when you vacuum. Why and how do I fix it???


I was experiencing the same problem right after changing the belt for the first time, as my Hoover is just a few months old. I am assuming what you are smelling is burnt rubber, like your belt, right? Well, if you have changed you ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

I have a Hoover WindTunnel, Self-propelled model, and it was working great until I ran over a portion of the cord, then it started making a bad noise and I noticed the roller is not moving consistently...I suspect I may have stetched the V-Belt...do you think so?


The V belt usually wears down first. Remove the roller and belt to visually check for wear and belt material in the roller pulley. I would change the flat belt as well. Also, replace the cord if any wires are exposed ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

How to clean hepa filter - Hoover U5753-900 WindTunnel Bagless Upright Vacuum


Run the HEPA filter under warm running water and allow to dry completely - preferably where it can get air from both sides of filter, do not dry in direct sunlight this can damage the filter, it is best in a warm room, can be dried in a dishdrainer i ... Hoover U5753-900 WindTunnel Bagless Upright Vacuum

I have a Hoover WindTunnel Bagless Vacuum Cleaner, Model #U5753-900, Serial number 110600215585, which I purchased from Loew's on 3/31/07. With it, came a Hoove Slider for hard floor surfaces, Model #S2105, Serial number 050500084989. The Slider strted making a noise--I thought something had been caught in the roller, but discovered, it had not; so I and my husband proceeded to take the Slider apart. I believe one of the belts had come off; but when we took the screws off the bottom to check


... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0422 seconds