Having problems with your Hoover U5753-900 WindTunnel Bagless Upright Vacuum ?

Cannot fit a belt to hoover whirlwind

\015 Cannot get the plate off to fit a new belt\015

Answers :

On the top of the base you will see three slots on each side of the top of the base the middle slot has a screw one on each side take those out and the cover will lift off.you will be at the roller and belt.lift up on the roller and put it on the side .you must clean the old rubber left on the motor shaft first before installing the new belt.otherwise the new belt won't last long.slip the belt over the motor shaft then put your roller brush through the new belt.you might have to pull forward on the roller to get it in place because of the new belt ,they are a little tight at the beginning.then alighn your roller ends and put the roller back in their slots.turn the roller by hand till the belt in in the middle of belt guide on the roller .now you can put the cover back on .then your in buisness.
Repair Help & Product Troubleshooting for Hoover U5753-900 WindTunnel Bagless Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Cannot fit a belt to hoover whirlwind


On the top of the base you will see three slots on each side of the top of the base the middle slot has a screw one on each side take those out and the cover will lift off.you will be at the roller and belt.lift up on the roller and put it on the sid ... Hoover U5753-900 WindTunnel Bagless Upright Vacuum

I have a Hoover Windtunnel U 6439-900. The agitator brush will not turn. I installed 2 new belts, # 38528034, and # 38528-035 There is so much slack in belt # 3852034 (brush drive) that it cannot grip the brush. There does not seem to be any adjustment to take up the slack. I've put in new belts twice now & cannot get brush to rotate or tighten the belt to the brush.


... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

Trying to fix new belt to Hoover Turbo Power vacuum cleaner. Don't see how the belt becomes taut. Fitting it around the roller, there is nowhere to fit the belt to, it just sits loose.


I looked at the user instructions guide online and saw where the 'other end' of the belt should be fitted. It was extremely hard to fit but eventually managed it. Thanks for this solution site. I wouldn't hesitate to use it again. ... Hoover U5396-900 Turbo Power Vacuum

I am a professional maid and one of my clients just had her Hoover Elite Vacuum belt break. I bought the belts ... but cannot find a manual online and do not know what the model number is. I am scheduled to be in her home in exactly one hour! HELP! HOW DO I CHANGE THE BELT -WHEN I CANNOT FIND A MANUAL? Many Thanks! Lynn


This is no problem! You will need a flat blade screwdriver and about 10 minutes! \015\012 \015\012*Always use genuine hoover parts for repairs, discount store belts can be as much as \015\0121" longer than OEM parts ... Hoover Elite U5061-900 Bagged Upright Vacuum

Just tried to fit a new belt to a vax quicklite 2 upright hoover and the belt snapped is there a right way to fit belt


... VAX Appliances Vax X3 Bagless Upright Vacuum

Can not find a proper fitting v-belt to fit my hoover wind tunnel cyclonic. i even ordered it from hoover.


The correct belt is # 38528034 ( package # 40201200 ) This belt may seem loose when it is installed, because there is an "idler bearing" that pushes down on it when the handle is released and dropped back. ... Hoover U5780-900 Windtunnel Cyclonic Bagless UprightVacuum

I have an old Hoover vacuum model # U5035-930. The belt broke and I tried replacing the belt myself. I couldn't stretch the belt to attach it to the motor pully. It was belt # 38525-027 M6. Which I got from the previous owner. I took it to a vacuum repair place and he replaced it with belt # 38528-027 J4. I cannot find this belt anywhere.


... Vacuums

Will hoover belt 31130 fit my hoover 3852840 - Hoover Vacuums


... Hoover Vacuums

I need to replace the belt on my hoover fusion plus upright vac. But I cannot find what belt it takes. the number on the belt is worn off


Hello : \015\012\015\0121:Unplug your Hoover vacuum. Turn the vacuum up-side-down and place the motor and vacuum portion on a counter top with the handle hanging down toward the floor. This makes it easy to work on the underside of ... Hoover Fusion Plus Cyclonic Upright Vacuum Vacuum

My fan belt on my hoover is broken,where is it located and how do i fit a new fan belt


I figured out on my hoover upright that many of those models don't access the belt by removing the plate under the vacume. the housing top actually prys off (with the help of a flathead screwdriver). step on the handle release button and lay the ha ... Hoover Vacuums

Where is the belt on a hoover agility?? My brushes stopped spinning and I think that the belt broke but I cannot find it


If you have the manual it should show the location of the screws or clips that hold the cover on for the belt. ... Hoover F6212-900 / F6215-900 SteamVac Agility Upright Vacuum

We had to take the bottom of the vacuum apart to remove dirt that had plugged the hose. We cannot put it back together so that the smaller round belt stays tight. I need a diagram of how this belt is supposed to fit.


Most vacuum manufacturers avoid putting their shop manual in the public domain. There are various reasons for this, some good ones.\015\012But I did find this. Maybe it'll help.\015\012 ... Hoover U6441-940 WindTunnel Bagged Upright Vacuum

I am trying to change the belt on a hoover legacy dirt finder. I cannot figure out how to get to the inside pully where the belt hooks


Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=733898\015\012Generic problem for all Vacuums\015\012I am trying to change\015\012Posted by fuzzyplus1 ... Vacuums

Need to replace 2 belts on the Panasonic MC-UG302 upright hoover and I dont know how to do it. Is it possible to get a brief discription/diagram of fitting belts from somewhere. Tks


... Panasonic Vacuums

Model UH70120 Hoover Wind Tunnel T Series Rewind Model UH70120 purchased at Target - bagless How can I put on the new Belt? I have taken it apart but cannot figure out how to change the belt. How?


... Hoover UH70120 WindTunnel TSeries Rewind Bagless Upright Vacuum Cleaner

Hoover model u5146900 the belt drive is bare metal wears out the belt quickly is there a part that fits over the pin?


The belt drive shaft does not actually wear out the belt unless it has a burr on it, however frequent use does.It should be kept clean and polished with no residual dirt ir burnd rubber. On a department store brand vac you should expect to chan ... Hoover U5144900 / U5146900 / U5147900 Tempo Bagged Upright Vacuum

Change Belt on Hoover Whirlwind 2000W


... Hoover Vacuums

I HAVE A HOOVER VACCUM CLEANER MODEL U8172-900. i HAVE TAKEN IT APART AND CANNOT TAKE THE TOP COVER OFF TO CHANGE THE BELT. CAN YOU HELP ME?


This must be a Savvy, Take off the plate covering the brush roll, then take out 2 screws from the bottom, turn it over, remove the Hoover emblem, there is another ***** there. Then the top cover will come off. ... Vacuums

What belt fits the 1700 turbopower hoover model


... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Hoover self propelled bagged windtunnel upright model #U6435-900...how do you remove the green plastic shell cover to get to the part that secures the v belt...we need to secure the bolt and cannot get the area. Brushes and transmission wheel not rotating? thanks


Greetings from GoVacuum,\015\012\015\012Here's a great video repair tutorial that we've put together to try and help you with the repair on your Hoover WindTunnel. I hope that this helps you with your repair. If you found this solution ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

How do I fit new belt ? - Hoover Vacuums


Take bottom cover off vacuum, ... Hoover Vacuums

Kirby hoover can you tell me hop i get roller of head to fit new belt. many thanks


Turn the latch to release the nozzle as. Take off the bottom plate, remove the brush roll, check it while you have it out, put a new belt over the brush roll and reinstall back into the nozzle, belt should be in the center, put the bottom plate back ... Kirby Ultimate G Bagged Upright Vacuum

I have an older hoover vacuum and cannot figure out how to put the belt on?


Http://www.geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=542813\015\012Generic problem for all Vacuums\015\012I have an older Hoover\015\012Posted by rrunne ... Vacuums

Brushes on hoover deluxe steam vac cvarpet cleaner are not rotating. Took out the brush assy and drive spins slowly but with little torque. Cannot seem to open the bottom to see if belt or direct drive..something wrong with drive mechanism for 5 brsuhes


(1) Assure the brush shut off lever on the hood is not set to the off position. \015\012(2) Is there still a square pin standing up from the one drive brush? It should be 1/4 square, and about two inches tall. That pin is the drive from the ... Hoover F5866-900 SteamVac Deluxe Wet/Dry Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.2982 seconds