Having problems with your Hoover U5753-900 WindTunnel Bagless Upright Vacuum ?

My Hoover Wind Tunnel has a burning smell when running. I replaced the belt, but this didn't help.


Answers :

Its clogged my vax does that burning smell when it gets clogged up thats for the five minutes before it overheats and stops
Repair Help & Product Troubleshooting for Hoover U5753-900 WindTunnel Bagless Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My Hoover Wind Tunnel has a burning smell when running. I replaced the belt, but this didn't help.


Its clogged my vax does that burning smell when it gets clogged up thats for the five minutes before it overheats and stops ... Hoover U5753-900 WindTunnel Bagless Upright Vacuum

When using my hoover wind tunnel the last few times it has emitted a burnt rubber smell so my husband checked the belt and is wasn't broken or off but now when I use the vacuum the beater bar doesn't seem to be going around as well as it should be can you help


I take it the belt was put back on !! i would say hubbi forgot the tension arm a little black striker that can go in two ways but put in back wards it will not tension the arm ... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

I have 2 Hoover Wind Tunnel-self propelled bagged vacuums-U6433-900 model.The roller bar does not agitate, the self propelled feature does not work and, in general, the vacuum is not performing well. I have replaced the roller bar, the v belt and the wide belt. The filters have been replaced and it has a new bag. I have had both of these since 2004 and they were fairly expensive $200 each) but if the repairs are prohibitive, I might as well get new vacuums. Suggestions? I just spent $100 for bel


The Hoover WindTunnel self propelled is a machine that we see in our retail stores (Vacuums Unlimited) constantly. The benefit of having a supposed "self-propelled" machine wears of quickly after the numerous time you will need to take this machine ... Hoover Vacuums

Is there any way to repair or replace the belt GUIDE on the inside of the belt compartment of a '97 Hoover Wind Tunnel (not self-propelled)? It became twisted when a belt broke and now the belt rubs against it and sounds really weird, and I'm sure new belts will continue to break.. This guide is a long piece of molded material (part of the compartent wall) to keep the belt from coming off the pulley. It also had a sort of metal clip on it. It was loose and I took it off because of the way the pa


Honestly you should take it to a vac.shop they can fix any vac. ... Windsor SR12 Sensor Bagged Upright Vacuum

Hoover Wind Tunnel 7500 Brush not Turning. I have replaced the Brush and the belt. The problem does not seem to be either to me. I believe might be a missing part. The place were the belt hooks on is a metal pole which never seems to grip the belt well. In fact it seems loose most of the time and slips on the brush, causing the belt to eventually burn up. Could there be a missing plastic or rubber piece meant to hold the belt taught  on the metal pole?


Check the Idler Pulley part Number 43241004 (Item 13 in the IPB)http://64.49.205.183/v/u6451900.pdf ... Vacuums

I have a hoover wind tunnel model# u6476-900 and I'm having trouble replacing the belt. The extra belt that came with it was belt # 38528-035 and it's smaller then the old one and I'm having a hard time putting it on. Is this the right size belt?


Yes it is the right belt. the easiest way to get that belt on is to put it on the motor shaft first, stretch and start at the top of the self propelled pulley and rotate til the belt tracks on. you will need to keep pressure on the belt while you rot ... Hoover U6476-900 WindTunnel Vacuum

Replacement belt # for hoover wind tunnel model u5750-900. original belt # 38528-035, please


Your belt number is correct ending in 035. I have had luck with belt number ending in 033 also. ... Hoover U5750-900 WindTunnel Bagless Upright Vacuum

Hi,My agitator brush won't run on my hoover S3590, I changed the belt, that didn't work. I don't see a possible cause in my book except replacing the belt. I think there could be a short, the brush will come on sometimes when pulling back and slightly lifting. Any ideas would be great and can I fix it myself? Thank you for any help, Bobbie


Hi Bobbie\015\012Take apart the electro floor head if you can and inspect inside - it may well be that there's clogged dust preventing the brush from turning and also check both sides of the actual beater bar as thread and tangled hair can often lead ... Hoover S3590 Bagged Canister Vacuum

I have a Hoover Wind Tunnel Self-propelled vacuum. I changed the belts because the brush was not turning. After replacing the belts the brush is still not turning what can be wrong?


There are two belts on the wind tunnel this video will show you how to repair ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

I heard that a class action lawsuit against Oreck Vacuum is being started because of all the problems customers are having with their vacuums. Does anyone know about this? My Oreck is only a couple of years old and keeps burning up belts. I took it in after only one week of usage when I started to notice white smoke coming out of it and the smell of burning rubber. I feel like I got the old run-around, when the service tech told me he couldn't find anything wrong (but replaced the burned up belt


You are correct about the fact that legal action has been taken. Go to this link to read more\015\012\015\012 ... Oreck XL2200 Bagged Upright Vacuum

My machine (Hoover Wind Tunnel - bagless) is only 1 yr. old. The agitator brush doesn't turn all the time. I know it's not supposed to turn when in the upright position. However, it only seems to work when I have the setting on high. When I stop, but have not put the machine in the upright position, it stops again and then slowly starts moving. Could the V-belt be worn out already? In the owner's manual it states that this belt is not normally replaced. The exact same thing happened with my old


Sounds like you should do two things:\015\0121- Remove and clean the beater brush of all debris as best you can. At the end of the brush you will see a hard rubber piece, at both ends, that holds it in place in the body of the vacuum.\015\012Add som ... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

No suction My Hoover Wind Tunnel vacuum runs but there is no suction. The last two or three times I used it, it shut itself off after having a burning smell. When I unplug it for the suggested 30 minutes, the motor will run again but no suction. What is wrong?? Should I just buy a nve one? This one is 8 years old.


Sounds like your motor bearings are going bad. This is generally indicated by the motor overheating, and the heat transferring out through the motor pulley, which is where the belt attaches. So, your machine is overheating, melting the belt, and then ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

HI, my motorized brush barely turns.It makes a hot rubber smell. I took apart and noticed the spindle the belt turns on discolored from heat. Cleaned it, but still no turning of the brush.The vac is a hoover wind tunnel. As it moved accidentally touched the belt/ spindle and burned my hand a little. Very hot in area. Bright spark from motor noted. Was careful not to touch that part!


That means that the belt is stretched and it is slipping on the motor shaft, that is why it is hot and smells like burning rubber. You need to replace the belt. Here is the correct belt you need: ... Hoover S3765-040 WindTunnel Bagless Canister Vacuum

Brush not working on self-propelled wind tunnel U6471-900.I have replaced belt but can't get off top cover.


... Vacuums

How to replace belt in Hoover U5402-900 Wind Tunnel Vacuum


... Hoover U5402-900 WindTunnel Vacuum

HOW DO I REPLACE THE DRIVE BELT ON A HOOVER WIND TUNNEL SELF PROPELLED


Take the brush belt and slip it over the pull into the groove. Then take the flat belt and hook onto the motor shaft and then pull belt over pull and push it around the entire pulley. It can be difficult but after the first time it is easy. You ha ... Hoover Company Wind Tunnel U53019 Upright Vacuum

6579-2 bissel power force. Belt was broken. Purchased new one. replaced. making loud noise and smells like burning. HELP


... Bissell 6594 PowerForce Bagless Upright Vacuum

My hoover elite rewind is making a louder noise and I can smell something burning when I use it. I have replaced the belt but this did not help.


The smell is either the motor or the belt, if motor hope it is under warranty, if belt make sure brush roll spins freely and replace belt, if brush roll not spin freely replace it first ... Hoover U5507900 Elite Rewind Bagless Upright Vacuum

Kenmore 116.23513301 Motor runs, but the brush will not rotate. Every time I hit the overload reset button, it will rotate for about a second then stop. I replaced the belt and cleaned around the brush, but the brush still will not rotate. Any help you can give me would be greatly appreciated.


If the motor on the power brush is running the belt is bad, if the motor on the power brush only runs when you push the overload, the overload is bad. ... Kenmore 22812 Bagged Canister Vacuum

I have a Hoover Wind Tunnel U6437-900. The brush will not turn. I have replaced both of the belts with no success. Any suggestions?


Hello,\015\012\015\012If you've already changed the belts and the machine still won't run, it can really be only a few things. \015\012\015\012The first thing you should check to make sure that the roller brush is good. Yo ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Wind tunnel two with bag, started with burning smell then shut off with red light on. Belt is fine but cannot get it to start again.


Sounds like your motor.Try replacing the brushes in the motor.If that does not work then the windings in the motor have burnt out. ... Vacuums

My wind tunnel keeps breaking its belt. The big one. The little one is properly attached. This is a recent problem so it has nothing to do with the rug height settings. I just broke two in the course of 15 minutes. The bag is NOT full, the brush/beater has been cleaned and properly attached Help.


Well will the brushes turn freely as they run in bearings if its got wool of cotton raped around the side of the brushs that will make them tight to turn and will brake every belt you put on it, in a flash,,,\015\012the other thing that causes ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

How to replace belt on Hoover U6626-900 Wind Tunnel bagless.


Hello,Click this to go to a site that will show you (complete with illustrations) how to change belt.http://www.info-vacuum-clea ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

How to replace belt on Hoover Wind tunnel vacuum


Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=831441\015\012Generic problem for all Vacuums\015\012How to replace belt on\015\012Posted by dinosir on ... Vacuums

Makes a loud noise like a grinding noise then smokes comes out and it smells like burning rubber? When I take the (rod) brush off with the belt then run the vacuum there is no more noise? Please help me thank you


Your belt is worn and stretched and so it is slipping on the motor drive shaft. That is why it is noisy and smells like burning rubber. You simply need to replace the belt. You can get replacement belts here: ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0913 seconds