Having problems with your Hoover U5753-900 WindTunnel Bagless Upright Vacuum ?

Windtunnel bagless will turn on but kills a few seconds later


Answers :

Motor is heating up could be shot . Does it throw the breaker?
Repair Help & Product Troubleshooting for Hoover U5753-900 WindTunnel Bagless Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Windtunnel bagless will turn on but kills a few seconds later


Motor is heating up could be shot . Does it throw the breaker? ... Hoover U5753-900 WindTunnel Bagless Upright Vacuum

No suction I have a similar problem - volta vortex bagless vacuum will not ****. Worked for 1 job then quit sucking, I have had the heads replaced, then the barrel - 2 months later same problem. I push the power lever to max - 10 seconds later it turns itself down and doesn't work properly. I am over it, now looking for refund


Hi there SmartAlec from NelsonVacuums.com.au here. The problem is going to be the filter. THis kind of vacuum basically replaces the bag with a simple filter and the vacuum ... Vacuums

I have Hoover Widepath Bagless 12 Amp Windtunnel vacuum. Yesterday I was vacuuming and smelled smoke and it shut itself off. Today I cleaned out the filters (they weren't bad) made sure nothing was obstructing the hoses or the spinning brush part. It turned on for 1 second, smells like smoke somewhere from the bottom and now won't turn back on so I don't know if anything is spinning or not. What can I do to fix this myself?


Hi There,\015\012\015\012When a vacuum cleaner smokes, it is usually only one of two possible problems.\015\012\015\012It could either be that your motor burned up, or that your belts burned. The belts on this particular mod ... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

Infinity Vaccum by Shark, model number NV31COS, will not start. The vacuum was running just fine until it grabbed the edge of a curtain. Turned it off to release the suction. Turned it back on and was working fine. About a minute later the vacuum was making an odd noise. Every 2 seconds or so it would "heave" (lack of a better word) then go away, then come back and so on. Turned the vacuum off and checked for blockage, none that could be seen or felt, and now the vacuum won't turn. Any suggestio


Carpet brush won't turn when vac on ... Euro-Pro NV31 Infinity Vacuum

Shark Euro-pro EP621 Bagless Upright Vacuum. Q regarding the brush not spinning / after troubleshooting and taking actions listed below, it now spinning for a few secs, but then stopping. Already removed hair, strings, etc. Checked that belt is aligned properly, checked that small wheel that turns belt is working (spins fine when belt removed. Oiled the turning parts a bit, that made it spin better, but still stops. It turns about 3-4 seconds then stops. If I switch it off and on again, I get ag


... Euro-Pro EP621 Bagless Upright Vacuum

Turned Hoover on and worked as normal for 10 mins then for a split second went off and then on again a coupe of seconds later went off completely. Tries different socket and changed the fuse. Still not working.


Internal short most likely to a feed wire to the motor ... Vacuums

My Windtunnel 2 keeps turning off after a few minutes or even seconds of use. We thought at first this was the thermal shutoff feature but this happens regardless of how long it has been turned off. The bag is empty and it doesn't appear there are any blockages. We purchased this a little over a year ago and are about ready to toss it.


Bought a BissellUnsubscribe us, we do not want to pay money for help support ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

My brand-new Hoover Windtunnel T-Series Pet Rewind Bagless vac simply shut off while I was using it and now I can't get it to turn back on. I've emptied the dirt collection bin and let the unit sit unplugged for 30 minutes to reset the Thermal Protector as per the manual. I've even tried a few different outlets just in case a fuse got tripped, but the vac still won't turn on. What happened? Do I need to return this vac to the store? I just bought it 5 hours ago.


... Hoover Vacuums

HOOVER SAVVY This is less than a year old (yep, no receipt) and all of a sudden last night the vacuum turns off after a moment of running. Also the red and green lights do not work at all. I've thoroughly cleaned the bagless unit, and it still won't work. It powers on for a split second then turns itself off. Help please.


I had the same problem. Took it in and the repair shop they said it was the switch. It was an $18 switch and $30 labor. Switch was a red on/off button with 2 wire leads and caps to screw on for connection. If you can wire a ceiling fan then this ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

I have a hoover windtunnel platinum. I have changed the bag ( hepa Q bag) but the bag light wont reset. so the vaccum wont turn on. I have unpluged it and let it set for a while with the new bag in and repluged it in. I have checked the brushes and it is all clean but it will not reset. This only the second bag so it is a new machine I should not be having problems. Is there some sore of reset button I can hit.


... Hoover Company Wind Tunnel U53019 Upright Vacuum

Hoover windtunnel bagless canister not turning on at all. we mistakenly dropped it after the first time it happened and it started working again. after using it the next time, it has stopped working once again. help!


... Hoover S3755 WindTunnel Bagless Canister Vacuum

Roller brush does not turn - Hoover U6630-900 WindTunnel Bagless Upright Vacuum


The drive belt is worn. you can get the replacement belt here:http://vacbelts.com/hoover-windtunnel-38528-035-belt.htm ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

Brush doesn't move when turned on - Hoover U5780-900 Windtunnel Cyclonic Bagless UprightVacuum


Replace both belts part # 38523-034 the V belt and 38528-035 the flat belt. Inspect the brushroll groove for wear. the top of the V belt should almost ride flush with the brushroll when you press your handle release and bring your head back. There is ... Hoover U5780-900 Windtunnel Cyclonic Bagless UprightVacuum

Have a hoover windtunnel platinum. I have changed the bag ( hepa Q bag) but the bag light wont reset. so the vaccum wont turn on. I have unpluged it and let it set for a while with the new bag in and repluged it in. I have checked the brushes and it is all clean but it will not reset. This only the second bag so it is a new machine I should not be having problems. Is there some sore of reset button I can hit.


... Hoover Ultra U6430-900 WindTunnel Bagged Upright Vacuum

Wind tunnel t series vacuum won't turn on - Hoover WindTunnel TSeries Bagless Upright Vacuum Cleaner UH70107


I had the same problem and used a tool to clean out the suction tube on my Windtunnel Series T. It was full of junk packed in tight. After cleaning it out there's no more turning off or overheating. It actually works better than when I first got it ( ... Hoover WindTunnel TSeries Bagless Upright Vacuum Cleaner UH70107

Vacuum turns on for approximately 300 seconds, then trips reset switch. ABout 2 minutes later the switch can be reset and the process starts all over again


... Broan-NuTone VX550 Bagged Central System Vacuum

Hoover Upright Bagless WindTunnel does not self propel (U6625-900). Belts are new, Brush turns strongly. Wheels propel forward very weakly and do not reverse when the handle is pulled backward. Is there a mechanical link from the self propel switch to the "transmission" ? Are there any gears that could be worn or not engaging properly?


... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

Suction will not turn on - Hoover S3755 WindTunnel Bagless Canister Vacuum


Might be the switch is faulty or the vacuum motor is not being activated or the motor by itself is defective.\012You might have eto take a look through the wiring to confirm if the volatge flows from the switch to the motor. ... Hoover S3755 WindTunnel Bagless Canister Vacuum

Hoover windtunnel bagless - won't turn off


BRUSH WON'T TURN ONE ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

Brush won't turn, belts intact - Hoover U5753-900 WindTunnel Bagless Upright Vacuum


Even though the belt is intact it can still be stretched and not turn the brush. You can get replacement belts here:www.vacbelts.com ... Hoover U5753-900 WindTunnel Bagless Upright Vacuum

My eureka vacuum won't suction and starts to smoke when I try to use it. It sounds like it is suctioning when I first turn it on, but after about 20 seconds it begins to smell like burning and does not suction at all. I have tried cleaning and unclogging the filter and everything. It's bagless so I don't need a new bag.


The problem is that your belt is stretched and worn. This causes that burning smell and it also causes the vacuum to not pick up well. You need to replace the belt. Here is the belt you need and the manual with instructions: ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum

Hoover UH70600 Windtunnel Max Multi-Cyclonic Bagless Upright Vacuum Brush won't turn after cleaning out debris, belt is fine.


... Hoover UH70600 Windtunnel Max Multi-Cyclonic Bagless Upright Vacuum, 7 Floor Settings, 15 Inch Cleaning Path, 28 Foot Cord Rewind, On Board Tools

My hoover elite belt comes off within 5 seconds of turning it on


Those machines sit in the box in transit across the world and waiting for purchase. In time the rubber stretches out from just sitting there. In the old days they packed the belt separate from the vacuum and you had to put in on yourself. Today's buy ... Hoover Elite Rewind Bagless Upright VacuumVacuum

The breaker on the vacuum trips after about 3 seconds on. The canister was extremely full and started to smell like burnt wood, we fully cleaned out the unit. Now when the vacuum is turned on, the motor sounds weak, and then turns off in a matter of seconds,and we have to reset the breaker on the vacuum to get it to start again for another few seconds.


This sounds indicative of a worn set of carbon brushes on a dieing motor for a central vac. the armature is ,likely damaged causing teh breaker to blow. Please post back with more details as to make and model. Do not atempt to run the vac ... Vacuums

I have a Bissell proheat 9200 T. The brushes engage when the handle is lowered. However they only turn for about 20 seconds then stop. If you turn the power off then on they run about 20 seconds again. It is driving me crazy!


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9200 Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0702 seconds