Having problems with your Hoover U5753-900 WindTunnel Bagless Upright Vacuum ?

My hoover wind tunnel self propelled vacuum wont stand up be itself. The locking thing is not working. Thank You. [email protected]

Answers :

If you look at the foot pedal, see if it is locked in the base, and pivots freely. I have seen some of these that break the base, or break the spring hinge on the back side of the release pedal.
Repair Help & Product Troubleshooting for Hoover U5753-900 WindTunnel Bagless Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My hoover wind tunnel self propelled vacuum wont stand up be itself. The locking thing is not working. Thank You. [email protected]

If you look at the foot pedal, see if it is locked in the base, and pivots freely. I have seen some of these that break the base, or break the spring hinge on the back side of the release pedal. ... Hoover U5753-900 WindTunnel Bagless Upright Vacuum

My Electrolux Pronto is not charging. When I put the Vacuum stick on the charging stand, the purple light goes on for about 5 seconds and then it will be off. I tried to clean both the terminal (Vacuum stick and the charging stand) but the same thing happens. What can I do to make it work?

Call electrolux there was a battery recall ... Electrolux EL1000A2 Pronto Bagless Stick Cyclonic Vacuum

Hi we have a model 31075 which i did not find in the list im hoping it's similar to the 31079 The problem is that the agitator has stopped working and i can not open it to find the problem is there a manual available or a site i can go to. Can you suggest what i can do to open it to look around I am very handy with most things but this thing has got me frustrated at this point. thanks for your help. Regards Chuck

... Kenmore 31079 Upright Vacuum

The bottom bar that encases the brush is flush to the floor when using the vacuum. This causes the suction to "stick" the vacuum to the floor (lamenate) and also as there is no ground clearance debris is just pushed around. We have to nearly stand the thing upright to get the ground clearance to be enough for things to start being sucked up. I have taken apart, re-assembled etc and nothing is working.

I'm having the same problem.  The bottom plate is not level with the floor unless the vacuum is nearly in the upright position.  Its like there should be a spring pushing the bottom plate towards the floor.  Anyone know how to fix this ... Dyson DC07 Bagless Upright Cyclonic Vacuum

My walkie talkies won't turn on. We've only used them a few times, and not recently. I charged the batteries, but it doesn't seem to want to switch on. I've pushed that grey side button. Is it possible that it's locked off? And, same problem is with both of them. Seems a basic question, I know. They should be working though. Thanks, Bruce

... Vacuums

I have a Kenmore canister vacuum cleaner model 116.23912 that I purchased in 2004. At times the machine works fine, while at other times it will not turn on. I've done a couple of things to try to diagnose the problem (can fill you in if you like) but have not been successful. I'd very much like your input. Thank you, Dave Binder

... Vacuums

I have a Bissell 3760-2 and while vacuuming it just shut off. The vacuum was plugged in and was on. Thought it might have quit because of the filters, so I cleaned them out and still does not work. Please help I'm totally clueless about this thing. Thanks Tony

... Bissell Vacuums

Good morning, I have a Krups Variomix 3000 Premium, don't have a user manual, and haven't used it yet as I can't get the blender to lock into place. The user manual downloads that are on-line say the link has been removed. Please can you help me get the blender to work? Thank you, Marian

This is listed under vacuum cleaners as the repair catagory, is that what it is? ... Vacuums

Hi, pressing the big red foot button on the dc25 lowers the cleaner to the working position,but it wont stand up again. would appreciate some help. thanks. TC

Sounds like the ball cradle is worn out, the springs are too stretched to pull the handle release pedal back into place. you can do one of two things, replace the cradle assy, or just lift the red pedal up when you raise the handle ... Dyson DC25 All Floors Bagless Upright Vacuum

My machine (Hoover Wind Tunnel - bagless) is only 1 yr. old. The agitator brush doesn't turn all the time. I know it's not supposed to turn when in the upright position. However, it only seems to work when I have the setting on high. When I stop, but have not put the machine in the upright position, it stops again and then slowly starts moving. Could the V-belt be worn out already? In the owner's manual it states that this belt is not normally replaced. The exact same thing happened with my old

Sounds like you should do two things:\015\0121- Remove and clean the beater brush of all debris as best you can. At the end of the brush you will see a hard rubber piece, at both ends, that holds it in place in the body of the vacuum.\015\012Add som ... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

Hello, I have a Riccar 8000. The belt works, the bar spins, and it will **** things up. However, it will not pick up threads and dog hair or anything from the carpeting. Mu husband took the bottom off and there were a couple of small parts on the plate. We have no idea where they belong. Could not see them in the photos in the manual. Could it possibly need a new roller? Any help would be most welcome. Thank you! Mary Simon

... Riccar Vacuums

I have a GE model #SCA1000HBB02. Recently the control buttons quit working. I thought maybe someone locked the controls but thats not the case. The display lights up shows the time but thats all. I unplugged it and then powered it back up the display comes up to set the time but the buttons will not allow. Any help would be appreciated. Thanks, Gary

Sorry but this is the vacuum area, your problem maybe the main board or a fuse. please go to the microwave forum. ... Vacuums

Sharp R-1480. Microwave would not start - jarred door, and it heated and worked. Replaced bottom of the 3 inter-lock door switches. Turns back on - all seems normal. No heat (it does overall sound louder). Thanks, Mark [email protected]

Hi Mark,It sounds like you have a magnetron problem now or at very least a rectifier that is shorted. The elevated sound level comes from one of those two components. But since you had a door switch problem I would lean toward ... Vacuums

Vacuum will not stand, I does not lock into place anymore and it will not **** up dirt, it worked fine yesterday, but this morning I started having these problems

... Vacuums

I purchased a brand new P113 Ryobi charger about 2 years ago. It has never worked. If I put a P104 battery in for a charge, it looks like it works correctly. I push the battery tester on the battery itself, and it says full charge, but when I go to use the bateery, it dies right away. I have tried three new P104 batteries. The batteries charge on my charger at work with no problem. The funny thing is, I don't need a battery in the charger and the charger does the same thing, It runs the test

If you have your receipt, check with Ryobi to see if it is still under warranty. It comes with either a 2 or 3 year warranty, depending on when it was purchased. If it is still covered, get it replaced/repaired. If it is not, buy the P117 charger. $3 ... Ryobi P113 18 Volt One Charger 140501001

Hoover wind tunnel 2 bagless vacuum not working

Place handle in low position and turn cleaner over so bottom side is up.\015\012Remove the 4 screws in bottom plate and lift off.\015\012Look on the left side of the agitator brush. You should see the belt there. Remove agi ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

I bought an old Juki Baby Lock 418 at a garage sale. It will sew for 3 or 4 inches and then seems to be off timing and locks up. I have no instruction manual. Is there a manual available for this old machine? I would prefer a downloadable manual because I already have money invested in the machine which doesn't seem to work. It was suppose to have been gone over at a repair shop before I purchased it and was told that it worked. .

... Vacuums

I just bought a Samsonite "Freeminder Flex" backpack with handle. My issue is with the lock... The combination for this lock was set to open at 0-0-0. It opened and locked perfectly at first. But after following the instruction to set up the new combination code, it doesnt lock anymore....please help and thanks! Linda

... Vacuums

We have a dyson vaccume and what ever makes it stand isnt working. I dont think we did anything wrong. But I cant make it stand.

The steel rod has come out of the groove that makes it go up/bown this video will show you. ... Dyson Vacuums


Send me your email address and I'll send you a copy of the manual\015\012\015\012wilhouse\015\012\015\[email protected] ... Euro-Pro Shark SC-505 Handheld Steam Vacuum

I can not get the food chute lid to lock on top cover. It will lock but not when the top is locked in place. thanks

Hello!what is the brand and model number?please post back! ... Vacuums

I bought a minifridge from a local target store about 2 years ago. The minifridge just all of sudden stopped working. is there any thing i can do to get this replaced or worked on so it can work again.

Hi,\015\012\015\012Those mini fridges have a thermoelectric cooling unit... when they go bad they are not repairable... unfortunately they are made intending for them to be thrown out when they fail... but so is alot of stuff these days.. ... Vacuums

Need part for stand of Hamilton Beach Scovill Model 44 Mixer. Part is locking rocker tab that hold mixer in place on stand or press to remove mixer head from stand. Don't need spring or pivot pin, just rocker tab. Don't have part number.

... Vacuums

Hoover floormate Hi, I'm not sure what the model number is on my Hoover Floormate, but I can't get the cleaning liquid to dispense. The vacuum(dry pickup works fine). The handle squeezes without a problem. It used to work without a problem and then I didn't use it for awhile. When I came back to it, it wasn't working. Thanks, Alissa

The tank sits on what is called the reservior asm. it is actuated by the control rod inside the handle. With the tank off, watch and see if you can see that rod hitting the reservior asm when you squeeze the trigger. If it is moving up and down on ... Hoover Floormate H3000 Upright Wet/Dry Vacuum

I bought my rainbow se vacum 4 years ago and I was using it and suddendly stoped working, I try to on no power I on and off not working at all. what shall i do is there posibility to work again.pls.help and tell me what is the best to do. thank you.

Hi, there is no reset button on a Rainbow vacuum. \015\012\015\012 All SE series vacuums have a built in thermal and load fuse on the motor, and if it blew, it has to be replaced, or wired directly, with out it on there.\015\012Moto ... Rainbow 75th Anniversary Canister Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0584 seconds